← Commit history
README.mdadded+67@@ -0,0 +1,67 @@+# PI7C9X760CZDEX++**Diodes Incorporated** · UART · QFN-24-EP(4x4)++PI7C9X760CZDEX from Diodes Incorporated, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | RESET | input | Active-LOW reset input. A LOW pulse longer than 40 ns resets internal registers, forces all outputs to their reset state, and enables mode strapping. UART TX is idle and RX is ignored while asserted. |+| 2 | XTAL1 | input | Crystal input or external clock input. Connect a crystal between XTAL1 and XTAL2 (up to 24 MHz), or drive with an external clock up to 64 MHz. |+| 3 | XTAL2 | output | Crystal oscillator output. Used together with XTAL1 to form the internal oscillator circuit; leave floating when driving XTAL1 from an external clock. |+| 4 | VDD | power_in | Positive supply. Wide operating range 1.8 V / 2.5 V / 3.3 V. Decouple locally to VSS. |+| 5 | I2C/SPI | input | Host interface select strap. HIGH selects the I2C-bus slave interface; LOW selects SPI mode 0 slave. Sampled at reset. |+| 6 | CS/A0 | input | In SPI mode: Schmitt-trigger active-LOW SPI chip-select (CS). In I2C mode: device address select bit A0 (combined with A1 selects the base slave address per Table 9). |+| 7 | SI/A1 | input | In SPI mode: SPI serial data input (MOSI). In I2C mode: device address select bit A1 (combined with A0 selects the base slave address per Table 9). |+| 8 | SO | tri_state | SPI serial data output (MISO), tri-stateable. In I2C-bus configuration this pin's function is undefined and must be left as no-connect (N.C.). |+| 9 | SCL/SCLK | input | I2C-bus clock (SCL) input, or SPI serial clock (SCLK) input. Function selected by the I2C/SPI strap on pin 5. |+| 10 | SDA | bidirectional | I2C-bus data line, open-drain (bidirectional) when I2C is selected. In SPI configuration this pin is undefined and must be tied to VSS. |+| 11 | IRQ | output | Interrupt output, open-drain, active-LOW. Requires an external pull-up (~1 kΩ at 3.3 V, 1.5 kΩ at 2.5 V) to VDD. Fires on GPIO input change, RX errors, RX data available, TX buffer space, or modem status changes when enabled in the IER. |+| 12 | GPIO0 | bidirectional | Programmable general-purpose I/O pin. Direction and level controlled by the GPIO register. |+| 13 | GPIO1 | bidirectional | Programmable general-purpose I/O pin. |+| 14 | GPIO2 | bidirectional | Programmable general-purpose I/O pin. |+| 15 | GPIO3 | bidirectional | Programmable general-purpose I/O pin. |+| 16 | VSS | power_in | Ground return. |+| 17 | GPIO4/DSR | bidirectional | Programmable I/O pin, or modem DSR (Data Set Ready) input when configured for modem control. |+| 18 | GPIO5/DTR | bidirectional | Programmable I/O pin, or modem DTR (Data Terminal Ready) output when configured for modem control. |+| 19 | GPIO6/CD | bidirectional | Programmable I/O pin, or modem CD (Carrier Detect) input when configured for modem control. |+| 20 | GPIO7/RI | bidirectional | Programmable I/O pin, or modem RI (Ring Indicator) input when configured for modem control. |+| 21 | RTS | output | UART request-to-send output, active-LOW. Reflects MCR[1] or, if auto-RTS is enabled in EFR[6], is automatically driven based on RX-FIFO fill. Also used as RS-485 driver direction control. |+| 22 | CTS | input | UART clear-to-send input, active-LOW. Readable via MSR[4]; also gates transmission when auto-CTS is enabled via EFR[7]. |+| 23 | TX | output | UART transmitter output. In local loopback mode the pin is disabled and TX data is internally routed to RX. |+| 24 | RX | input | UART receiver input. In local loopback mode the pin is disabled and the internal TX is looped back to RX. |+| EP | VSS | power_in | Exposed thermal/center pad on the underside of the QFN-24. Metallic; must be soldered to the PCB ground plane. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Diodes Incorporated |+| Package | QFN-24-EP(4x4) |+| Category | Interface |+| Pins | 25 |++## Ordering variants++Same part, different packaging or reel option.++- `PI7C9X760CZDEX`+- `PI7C9X760CZDEXL`++## CAD (KiCad official)++- Symbol: `PI7C9X760CZDEX`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Diodes Incorporated datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8560088737129926656) (52 pp, sha256 `f897ef4d5061537b`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/pi7c9x760czdex-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "pi7c9x760czdex",+ "version": "0.1.0",+ "type": "component",+ "description": "Diodes Incorporated UART, QFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "pi7c9x760czdex"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "pi7c9x760czdex.kicad_sym",+ "pi7c9x760czdex.kicad_mod",+ "pi7c9x760czdex.glb",+ "pi7c9x760czdex.step",+ "pi7c9x760czdex.lbr",+ "docs/hero.png",+ "docs/pi7c9x760czdex-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}