← Commit history

Publish 0.1.1

Ray ·6d20fffd9a · ·parent c63482c
5 files changed +163−158
README.md+67−67
@@ -8,38 +8,38 @@ PCA8561BHN from NXP Semicon, in a HVQFN-32-EP(5x5). Pinout and pin descriptions  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | COM3 | output | LCD backplane output that must be directly connected to the LCD; it is used in 1:4 multiplex mode and may be left open-circuit if fewer than four backplanes are required. |-| 2 | VLCD | power_in | LCD supply voltage (1.8 V to 5.5 V); it must never be asserted before VDD and must not be connected while VDD is switched off. |-| 3 | VDD | power_in | Supply voltage (1.8 V to 5.5 V); a decoupling capacitor of at least 100 nF is recommended for the supplies. |+| 1 | COM3 | output | LCD backplane output COM3, used in 1:4 multiplex mode and must be directly connected to the LCD; left open-circuit if unused. |+| 2 | VLCD | power_in | LCD supply voltage, specified at 1.8 V to 5.5 V and must never be asserted before VDD. |+| 3 | VDD | power_in | Supply voltage, specified at 1.8 V to 5.5 V. | | 4 | VSS | power_in | Ground supply; the die paddle (exposed pad) is connected to VSS and should be electrically isolated. |-| 5 | RST | input | Reset input, active LOW; when the internal POR is disabled (PORE tied to VSS) the chip must be reset by driving RST to logic 0 for at least 10 µs. |-| 6 | SDIO | bidirectional | SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL. |+| 5 | RST | input | Reset input, active LOW; holding it low for at least 10 µs resets the device when the internal POR is disabled. |+| 6 | SDIO | bidirectional | SPI-bus serial data input/output (PCA8561B); input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL. | | 7 | CLK | bidirectional | Internal oscillator output or external oscillator input; must be left open if unused. |-| 8 | SCL | input | SPI-bus serial clock input; the input may be higher than VDD. |-| 9 | CE | input | Chip enable input, active LOW; the chip enable must not be wired permanently LOW. |-| 10 | PORE | input | Power-On Reset enable: connect to VDD to enable the POR, or connect to VSS (or leave open) to disable it. |-| 11 | n.c. | unconnected | Not connected. |-| 12 | SEG0 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 13 | SEG1 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 14 | SEG2 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 15 | SEG3 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 16 | SEG4 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 17 | SEG5 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 18 | SEG6 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 19 | SEG7 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 20 | SEG8 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 21 | SEG9 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 22 | SEG10 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 23 | SEG11 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 24 | SEG12 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 25 | SEG13 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 26 | SEG14 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 27 | SEG15 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 28 | SEG16 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 29 | SEG17 | output | LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit. |-| 30 | COM0 | output | LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit. |-| 31 | COM1 | output | LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit. |-| 32 | COM2 | output | LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit. |+| 8 | SCL | input | Serial clock input for the SPI-bus; input may be higher than VDD, and the maximum SPI clock is 5 MHz. |+| 9 | CE | input | SPI-bus chip enable input, active LOW; must not be wired permanently LOW. |+| 10 | PORE | input | Power-On Reset enable: connect to VDD to enable the internal POR, or to VSS (or leave open) to disable it. |+| 11 | n.c. | unconnected | Not connected in the PCA8561BHN (SPI-bus version). |+| 12 | SEG0 | output | LCD segment output SEG0, must be directly connected to the LCD; left open-circuit if unused. |+| 13 | SEG1 | output | LCD segment output SEG1, must be directly connected to the LCD; left open-circuit if unused. |+| 14 | SEG2 | output | LCD segment output SEG2, must be directly connected to the LCD; left open-circuit if unused. |+| 15 | SEG3 | output | LCD segment output SEG3, must be directly connected to the LCD; left open-circuit if unused. |+| 16 | SEG4 | output | LCD segment output SEG4, must be directly connected to the LCD; left open-circuit if unused. |+| 17 | SEG5 | output | LCD segment output SEG5, must be directly connected to the LCD; left open-circuit if unused. |+| 18 | SEG6 | output | LCD segment output SEG6, must be directly connected to the LCD; left open-circuit if unused. |+| 19 | SEG7 | output | LCD segment output SEG7, must be directly connected to the LCD; left open-circuit if unused. |+| 20 | SEG8 | output | LCD segment output SEG8, must be directly connected to the LCD; left open-circuit if unused. |+| 21 | SEG9 | output | LCD segment output SEG9, must be directly connected to the LCD; left open-circuit if unused. |+| 22 | SEG10 | output | LCD segment output SEG10, must be directly connected to the LCD; left open-circuit if unused. |+| 23 | SEG11 | output | LCD segment output SEG11, must be directly connected to the LCD; left open-circuit if unused. |+| 24 | SEG12 | output | LCD segment output SEG12, must be directly connected to the LCD; left open-circuit if unused. |+| 25 | SEG13 | output | LCD segment output SEG13, must be directly connected to the LCD; left open-circuit if unused. |+| 26 | SEG14 | output | LCD segment output SEG14, must be directly connected to the LCD; left open-circuit if unused. |+| 27 | SEG15 | output | LCD segment output SEG15, must be directly connected to the LCD; left open-circuit if unused. |+| 28 | SEG16 | output | LCD segment output SEG16, must be directly connected to the LCD; left open-circuit if unused. |+| 29 | SEG17 | output | LCD segment output SEG17, must be directly connected to the LCD; left open-circuit if unused. |+| 30 | COM0 | output | LCD backplane output COM0, must be directly connected to the LCD; left open-circuit if unused. |+| 31 | COM1 | output | LCD backplane output COM1, must be directly connected to the LCD; left open-circuit if unused. |+| 32 | COM2 | output | LCD backplane output COM2, must be directly connected to the LCD; left open-circuit if unused. | | 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |  ## Key specifications@@ -59,49 +59,49 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries |---|---|---|---|---|---|---|---| | VDD supply voltage | VDD | 1.8 |  | 5.5 | V |  | 30 | | LCD supply voltage | VLCD | 1.8 |  | 5.5 | V |  | 30 |-| IDD supply current | IDD |  | 1.8 | 3 | μA | ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C | 30 |+| supply current | IDD |  | 1.8 | 3 | μA | ffr = 64 Hz; no bus activity; VDD = 5.5 V; Tamb = 105 °C | 30 | | LCD supply current | IDD(LCD) |  | 3.7 | 4.7 | μA | ffr = 64 Hz; no bus activity; VLCD = 5.5 V; Tamb = 105 °C; BOOST = 0; no display load | 30 |-| Leakage current, any input pin except RST, after ESD event | IL | -500 |  | 500 | nA | after ESD event | 30 |-| LOW-level output current on pin CLK | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin CLK | 30 |-| LOW-level output current on pin SDIO | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V; on pin SDIO | 30 |-| HIGH-level output current on pins SDIO, CLK | IOH | 2 |  |  | mA | output source current; on pins SDIO, CLK; VOH = 4.6 V; VDD = 5 V | 30 |-| Output voltage variation | ΔVo | -100 |  | 100 | mV | VLCD = 5 V | 30 |-| Output resistance | Ro |  | 1.5 | 3 | kΩ | VLCD = 5 V | 31 |-| Frame frequency FF[2:0] = 001 | ffr | 42 | 64 | 86 | Hz | FF[2:0] = 001 | 33 |-| External clock frequency | fclk(ext) |  |  | 4096 | Hz |  | 33 |-| HIGH-level clock time | tclk(H) | 60 |  |  | μs | external clock | 33 |-| LOW-level clock time | tclk(L) | 60 |  |  | μs | external clock | 33 |-| Reset pulse width on pin RST | tw(rst) | 10 |  |  | μs |  | 33 |-| SCL clock frequency (SPI) | fSCL |  |  | 5 | MHz |  | 35 |-| LOW period of the SCL clock (SPI) | tLOW | 150 |  |  | ns |  | 35 |-| HIGH period of the SCL clock (SPI) | tHIGH | 80 |  |  | ns |  | 35 |-| Rise time of SCL (SPI) | tr |  |  | 100 | ns |  | 35 |-| Fall time of SCL (SPI) | tf |  |  | 100 | ns |  | 35 |+| LOW-level output current on pin CLK | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V | 30 |+| LOW-level output current on pin SDIO | IOL | 2 |  |  | mA | output sink current; VOL = 0.4 V; VDD = 5 V | 30 |+| HIGH-level output current on pins SDIO, CLK | IOH | 2 |  |  | mA | output source current; VOH = 4.6 V; VDD = 5 V | 30 |+| leakage current after ESD event | IL | -500 |  | 500 | nA | after ESD event | 30 |+| output voltage variation | ΔVo | -100 |  | 100 | mV | VLCD = 5 V | 30 |+| output resistance | Ro |  | 1.5 | 3 | kΩ | VLCD = 5 V; outputs measured one at a time | 31 |+| frame frequency FF[2:0] = 001 | ffr | 42 | 64 | 86 | Hz | FF[2:0] = 001 | 33 |+| external clock frequency | fclk(ext) |  |  | 4096 | Hz |  | 33 |+| HIGH-level clock time external clock | tclk(H) | 60 |  |  | μs | external clock | 33 |+| LOW-level clock time external clock | tclk(L) | 60 |  |  | μs | external clock | 33 |+| reset pulse width on pin RST | tw(rst) | 10 |  |  | μs |  | 33 |+| SCL clock frequency | fSCL |  |  | 5 | MHz |  | 35 |+| LOW period of the SCL clock | tLOW | 150 |  |  | ns |  | 35 |+| HIGH period of the SCL clock | tHIGH | 80 |  |  | ns |  | 35 |+| rise time | tr |  |  | 100 | ns |  | 35 |+| fall time | tf |  |  | 100 | ns |  | 35 | | CE_N set-up time | tsu(CE_N) | 30 |  |  | ns |  | 36 | | CE_N hold time | th(CE_N) | 10 |  |  | ns |  | 36 | | CE_N recovery time | trec(CE_N) | 70 |  |  | ns |  | 36 |-| SDIO set-up time write data | tsu | 5 |  |  | ns |  | 36 |-| SDIO hold time write data | th | 50 |  |  | ns |  | 36 |+| set-up time write data | tsu | 5 |  |  | ns |  | 36 |+| hold time write data | th | 50 |  |  | ns |  | 36 | | SDIO read delay time | td(R)SDIO |  |  | 150 | ns | CL = 50 pF | 36 | | SDIO disable time | tdis(SDIO) |  |  | 50 | ns | no load | 36 |-| Transition time from SDI to SDO | tt(SDI-SDO) | 0 |  |  | ns | write to read mode | 36 |-| VDD supply voltage (absolute maximum) | VDD | -0.5 |  | 6.5 | V |  | 29 |-| VLCD LCD supply voltage (absolute maximum) | VLCD | -0.5 |  | 6.5 | V |  | 29 |-| Input voltage | VI | -0.5 |  | 6.5 | V |  | 29 |-| Output voltage | VO | -0.5 |  | 6.5 | V |  | 29 |-| Input current | II | -10 |  | 10 | mA |  | 29 |-| Output current | IO | -10 |  | 10 | mA |  | 29 |-| Supply current | IDD | -50 |  | 50 | mA |  | 29 |+| transition time from SDI to SDO | tt(SDI-SDO) | 0 |  |  | ns | write to read mode | 36 |+| VDD supply voltage | VDD | -0.5 |  | 6.5 | V |  | 29 |+| VLCD LCD supply voltage | VLCD | -0.5 |  | 6.5 | V |  | 29 |+| input voltage | VI | -0.5 |  | 6.5 | V |  | 29 |+| output voltage | VO | -0.5 |  | 6.5 | V |  | 29 |+| input current | II | -10 |  | 10 | mA |  | 29 |+| output current | IO | -10 |  | 10 | mA |  | 29 |+| supply current | IDD | -50 |  | 50 | mA |  | 29 | | LCD supply current | IDD(LCD) | -50 |  | 50 | mA |  | 29 |-| Ground supply current | ISS | -50 |  | 50 | mA |  | 29 |-| Total power dissipation | Ptot |  |  | 100 | mW |  | 29 |-| Output power | Po |  |  | 100 | mW |  | 29 |-| Electrostatic discharge voltage HBM on pins SCL, SDA, CE | VESD | -2000 |  | 2000 | V | HBM; on pins SCL, SDA, CE | 29 |-| Electrostatic discharge voltage HBM on all other pins | VESD | -3500 |  | 3500 | V | HBM; on all other pins | 29 |-| Electrostatic discharge voltage CDM | VESD | -2000 |  | 2000 | V | CDM | 29 |-| Latch-up current | Ilu |  |  | 200 | mA |  | 29 |-| Storage temperature | Tstg | -55 |  | 150 | °C |  | 29 |-| Ambient temperature operating device | Tamb | -40 |  | 105 | °C | operating device | 29 |+| ground supply current | ISS | -50 |  | 50 | mA |  | 29 |+| total power dissipation | Ptot |  |  | 100 | mW |  | 29 |+| output power | Po |  |  | 100 | mW |  | 29 |+| electrostatic discharge voltage HBM | VESD | -2000 |  | 2000 | V | HBM; on pins SCL, SDA, CE | 29 |+| electrostatic discharge voltage HBM | VESD | -3500 |  | 3500 | V | HBM; on all other pins | 29 |+| electrostatic discharge voltage CDM | VESD | -2000 |  | 2000 | V | CDM | 29 |+| latch-up current | Ilu |  |  | 200 | mA |  | 29 |+| storage temperature | Tstg | -55 |  | 150 | °C |  | 29 |+| ambient temperature operating device | Tamb | -40 |  | 105 | °C |  | 29 |  ## CAD (land: KiCad; 3D: generated from the datasheet) @@ -114,7 +114,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf) (50 pp, sha256 `49517ebdf09b65e8`, retrieved 2026-11-12, tier: manufacturer)+- **Datasheet:** [NXP Semicon datasheet](https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf) (50 pp, sha256 `49517ebdf09b65e8`, retrieved 2026-11-13, tier: manufacturer) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated). 
package.json+45−44
@@ -1,6 +1,6 @@ {   "slug": "pca8561bhn-ay",-  "version": "0.1.0",+  "version": "0.1.1",   "type": "component",   "description": "NXP Semicon LCD Drivers, HVQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",   "tags": [@@ -49,18 +49,19 @@     },     "distributor_links": {       "lcsc": "C2653714",-      "digikey": "568-13033-2-ND"+      "digikey": "568-13033-2-ND",+      "mouser": "771-PCA8561BHN/AY"     },     "distributor_check": {-      "checked_at": "2026-11-12T22:11:02Z",+      "checked_at": "2026-11-13T02:42:27Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "568-13033-2-ND",         "status": "found"       },       "mouser": {-        "pn": null,-        "status": "quota"+        "pn": "771-PCA8561BHN/AY",+        "status": "found"       },       "matched_as": "PCA8561BHN/AY"     },@@ -69,19 +70,19 @@         "number": "1",         "name": "COM3",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; it is used in 1:4 multiplex mode and may be left open-circuit if fewer than four backplanes are required."+        "description": "LCD backplane output COM3, used in 1:4 multiplex mode and must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "2",         "name": "VLCD",         "type": "power_in",-        "description": "LCD supply voltage (1.8 V to 5.5 V); it must never be asserted before VDD and must not be connected while VDD is switched off."+        "description": "LCD supply voltage, specified at 1.8 V to 5.5 V and must never be asserted before VDD."       },       {         "number": "3",         "name": "VDD",         "type": "power_in",-        "description": "Supply voltage (1.8 V to 5.5 V); a decoupling capacitor of at least 100 nF is recommended for the supplies."+        "description": "Supply voltage, specified at 1.8 V to 5.5 V."       },       {         "number": "4",@@ -93,13 +94,13 @@         "number": "5",         "name": "RST",         "type": "input",-        "description": "Reset input, active LOW; when the internal POR is disabled (PORE tied to VSS) the chip must be reset by driving RST to logic 0 for at least 10 µs."+        "description": "Reset input, active LOW; holding it low for at least 10 µs resets the device when the internal POR is disabled."       },       {         "number": "6",         "name": "SDIO",         "type": "bidirectional",-        "description": "SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."+        "description": "SPI-bus serial data input/output (PCA8561B); input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."       },       {         "number": "7",@@ -111,151 +112,151 @@         "number": "8",         "name": "SCL",         "type": "input",-        "description": "SPI-bus serial clock input; the input may be higher than VDD."+        "description": "Serial clock input for the SPI-bus; input may be higher than VDD, and the maximum SPI clock is 5 MHz."       },       {         "number": "9",         "name": "CE",         "type": "input",-        "description": "Chip enable input, active LOW; the chip enable must not be wired permanently LOW."+        "description": "SPI-bus chip enable input, active LOW; must not be wired permanently LOW."       },       {         "number": "10",         "name": "PORE",         "type": "input",-        "description": "Power-On Reset enable: connect to VDD to enable the POR, or connect to VSS (or leave open) to disable it."+        "description": "Power-On Reset enable: connect to VDD to enable the internal POR, or to VSS (or leave open) to disable it."       },       {         "number": "11",         "name": "n.c.",         "type": "unconnected",-        "description": "Not connected."+        "description": "Not connected in the PCA8561BHN (SPI-bus version)."       },       {         "number": "12",         "name": "SEG0",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG0, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "13",         "name": "SEG1",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG1, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "14",         "name": "SEG2",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG2, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "15",         "name": "SEG3",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG3, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "16",         "name": "SEG4",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG4, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "17",         "name": "SEG5",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG5, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "18",         "name": "SEG6",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG6, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "19",         "name": "SEG7",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG7, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "20",         "name": "SEG8",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG8, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "21",         "name": "SEG9",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG9, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "22",         "name": "SEG10",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG10, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "23",         "name": "SEG11",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG11, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "24",         "name": "SEG12",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG12, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "25",         "name": "SEG13",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG13, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "26",         "name": "SEG14",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG14, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "27",         "name": "SEG15",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG15, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "28",         "name": "SEG16",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG16, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "29",         "name": "SEG17",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG17, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "30",         "name": "COM0",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit."+        "description": "LCD backplane output COM0, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "31",         "name": "COM1",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit."+        "description": "LCD backplane output COM1, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "32",         "name": "COM2",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit."+        "description": "LCD backplane output COM2, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "33",@@ -275,12 +276,12 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The exposed die paddle (thermal pad) of the HVQFN32 package is not given a pin number in the datashe; Pin 11 is printed as n.c. (not connected) on the PCA8561BHN; the PCA8561AHN uses pin 11 as A1 and pi; Pin types for CLK and SDIO are given as bidirectional (datasheet: input/output). The datasheet text ",-          "1/33 pins cited to the wrong page (name found elsewhere): ['9:CE@p26']"+          "extractor flagged: The exposed die paddle (exposed pad) of the HVQFN32 package is not given a number on the pinout figu; Pin 6 and pin 9 are shown with different names depending on bus type. The PCA8561BHN (SPI-bus) pinou; Pin 11 is n.c. (not connected) in the SPI variant; on the I2C variant it is A1. Only the SPI-variant",+          "exposed pad 33 added from the footprint"         ],         "pages_sent": 50,-        "cost_usd": 0.0377,-        "at": "2026-11-12T22:10:49"+        "cost_usd": 0.0337,+        "at": "2026-11-13T02:42:14"       },       "datasheet": {         "url": "https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf",@@ -323,8 +324,8 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "12a5baca039c8a9300d65ae454c37690bc4bf22c616d5c399540fc45420b8491",-        "checked": "2026-11-12",+        "sha256": "c2077b952f3e1f0e1330e4b436b88a6f2e4f9da343b1a17ebf2b8d00d0855ec5",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -342,13 +343,13 @@         "zmin_mm": 0.0,         "centre_offset_mm": 0.0,         "footprint_binding": "identity",-        "sha256": "ba1101a04f1e19a9622b1654b1a48b4db2aa6a180837fe045a50bc16980e9f76",-        "checked": "2026-11-12",+        "sha256": "89d905795bdcb7acadec3fd3b5b7e85050149e720593a4deea0aa5fad70c56be",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],     "package_dims": {-      "package_code": "SOT617-3",+      "package_code": "SOT617-3 (HVQFN32)",       "source_page": 38,       "D": {         "nom_mm": 5.0,
page.json+48−45
@@ -4,7 +4,7 @@   "slug": "pca8561bhn-ay",   "title": "PCA8561BHN/AY",   "brief": "NXP Semicon LCD Drivers, HVQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.1.0",+  "version": "0.1.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",@@ -32,18 +32,19 @@     },     "distributor_links": {       "lcsc": "C2653714",-      "digikey": "568-13033-2-ND"+      "digikey": "568-13033-2-ND",+      "mouser": "771-PCA8561BHN/AY"     },     "distributor_check": {-      "checked_at": "2026-11-12T22:11:02Z",+      "checked_at": "2026-11-13T02:42:27Z",       "source": "Component Ocean /api/assign-pns",       "digikey": {         "pn": "568-13033-2-ND",         "status": "found"       },       "mouser": {-        "pn": null,-        "status": "quota"+        "pn": "771-PCA8561BHN/AY",+        "status": "found"       },       "matched_as": "PCA8561BHN/AY"     },@@ -52,19 +53,19 @@         "number": "1",         "name": "COM3",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; it is used in 1:4 multiplex mode and may be left open-circuit if fewer than four backplanes are required."+        "description": "LCD backplane output COM3, used in 1:4 multiplex mode and must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "2",         "name": "VLCD",         "type": "power_in",-        "description": "LCD supply voltage (1.8 V to 5.5 V); it must never be asserted before VDD and must not be connected while VDD is switched off."+        "description": "LCD supply voltage, specified at 1.8 V to 5.5 V and must never be asserted before VDD."       },       {         "number": "3",         "name": "VDD",         "type": "power_in",-        "description": "Supply voltage (1.8 V to 5.5 V); a decoupling capacitor of at least 100 nF is recommended for the supplies."+        "description": "Supply voltage, specified at 1.8 V to 5.5 V."       },       {         "number": "4",@@ -76,13 +77,13 @@         "number": "5",         "name": "RST",         "type": "input",-        "description": "Reset input, active LOW; when the internal POR is disabled (PORE tied to VSS) the chip must be reset by driving RST to logic 0 for at least 10 µs."+        "description": "Reset input, active LOW; holding it low for at least 10 µs resets the device when the internal POR is disabled."       },       {         "number": "6",         "name": "SDIO",         "type": "bidirectional",-        "description": "SPI-bus serial data input/output; input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."+        "description": "SPI-bus serial data input/output (PCA8561B); input data are sampled on the rising edge of SCL and output data are valid after the falling edge of SCL."       },       {         "number": "7",@@ -94,151 +95,151 @@         "number": "8",         "name": "SCL",         "type": "input",-        "description": "SPI-bus serial clock input; the input may be higher than VDD."+        "description": "Serial clock input for the SPI-bus; input may be higher than VDD, and the maximum SPI clock is 5 MHz."       },       {         "number": "9",         "name": "CE",         "type": "input",-        "description": "Chip enable input, active LOW; the chip enable must not be wired permanently LOW."+        "description": "SPI-bus chip enable input, active LOW; must not be wired permanently LOW."       },       {         "number": "10",         "name": "PORE",         "type": "input",-        "description": "Power-On Reset enable: connect to VDD to enable the POR, or connect to VSS (or leave open) to disable it."+        "description": "Power-On Reset enable: connect to VDD to enable the internal POR, or to VSS (or leave open) to disable it."       },       {         "number": "11",         "name": "n.c.",         "type": "unconnected",-        "description": "Not connected."+        "description": "Not connected in the PCA8561BHN (SPI-bus version)."       },       {         "number": "12",         "name": "SEG0",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG0, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "13",         "name": "SEG1",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG1, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "14",         "name": "SEG2",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG2, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "15",         "name": "SEG3",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG3, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "16",         "name": "SEG4",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG4, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "17",         "name": "SEG5",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG5, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "18",         "name": "SEG6",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG6, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "19",         "name": "SEG7",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG7, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "20",         "name": "SEG8",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG8, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "21",         "name": "SEG9",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG9, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "22",         "name": "SEG10",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG10, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "23",         "name": "SEG11",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG11, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "24",         "name": "SEG12",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG12, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "25",         "name": "SEG13",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG13, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "26",         "name": "SEG14",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG14, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "27",         "name": "SEG15",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG15, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "28",         "name": "SEG16",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG16, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "29",         "name": "SEG17",         "type": "output",-        "description": "LCD segment output that must be directly connected to the LCD; unused segment outputs must be left open-circuit."+        "description": "LCD segment output SEG17, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "30",         "name": "COM0",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit."+        "description": "LCD backplane output COM0, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "31",         "name": "COM1",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit."+        "description": "LCD backplane output COM1, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "32",         "name": "COM2",         "type": "output",-        "description": "LCD backplane output that must be directly connected to the LCD; unused outputs may be left open-circuit."+        "description": "LCD backplane output COM2, must be directly connected to the LCD; left open-circuit if unused."       },       {         "number": "33",@@ -258,12 +259,12 @@         "consensus": "agreed",         "guards": "pin_guards 0.1: passed",         "guard_notes": [-          "extractor flagged: The exposed die paddle (thermal pad) of the HVQFN32 package is not given a pin number in the datashe; Pin 11 is printed as n.c. (not connected) on the PCA8561BHN; the PCA8561AHN uses pin 11 as A1 and pi; Pin types for CLK and SDIO are given as bidirectional (datasheet: input/output). The datasheet text ",-          "1/33 pins cited to the wrong page (name found elsewhere): ['9:CE@p26']"+          "extractor flagged: The exposed die paddle (exposed pad) of the HVQFN32 package is not given a number on the pinout figu; Pin 6 and pin 9 are shown with different names depending on bus type. The PCA8561BHN (SPI-bus) pinou; Pin 11 is n.c. (not connected) in the SPI variant; on the I2C variant it is A1. Only the SPI-variant",+          "exposed pad 33 added from the footprint"         ],         "pages_sent": 50,-        "cost_usd": 0.0377,-        "at": "2026-11-12T22:10:49"+        "cost_usd": 0.0337,+        "at": "2026-11-13T02:42:14"       },       "datasheet": {         "url": "https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf",@@ -306,8 +307,8 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "12a5baca039c8a9300d65ae454c37690bc4bf22c616d5c399540fc45420b8491",-        "checked": "2026-11-12",+        "sha256": "c2077b952f3e1f0e1330e4b436b88a6f2e4f9da343b1a17ebf2b8d00d0855ec5",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -325,13 +326,13 @@         "zmin_mm": 0,         "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "ba1101a04f1e19a9622b1654b1a48b4db2aa6a180837fe045a50bc16980e9f76",-        "checked": "2026-11-12",+        "sha256": "89d905795bdcb7acadec3fd3b5b7e85050149e720593a4deea0aa5fad70c56be",+        "checked": "2026-11-13",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ],     "package_dims": {-      "package_code": "SOT617-3",+      "package_code": "SOT617-3 (HVQFN32)",       "source_page": 38,       "D": {         "nom_mm": 5,@@ -965,5 +966,7 @@   ],   "visibility": {     "public": true-  }+  },+  "description": "NXP Semicon LCD Drivers, HVQFN-32-EP(5x5). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "org": "adom" }\ No newline at end of file
pca8561bhn-ay.lbr+2−1
@@ -202,8 +202,9 @@         <technology name="">           <attribute name="MPN" value="PCA8561BHN/AY" constant="no"/>           <attribute name="MANUFACTURER" value="NXP Semicon" constant="no"/>-          <attribute name="DATASHEET" value="https://www.nxp.com/docs/en/data-sheet/PCA8561BHN.pdf" constant="no"/>+          <attribute name="DATASHEET" value="https://www.nxp.com/docs/en/data-sheet/PCA8561.pdf" constant="no"/>           <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/pca8561bhn-ay" constant="no"/>+          <attribute name="MOUSER_PN" value="771-PCA8561BHN/AY" constant="no"/>           <attribute name="DIGIKEY_PN" value="568-13033-2-ND" constant="no"/>           <attribute name="LCSC_PN" value="C2653714" constant="no"/>         </technology>
pca8561bhn-ay.step+1−1
@@ -1,7 +1,7 @@ ISO-10303-21; HEADER; FILE_DESCRIPTION(('Open CASCADE Model'),'2;1');-FILE_NAME('Open CASCADE Shape Model','2026-11-12T22:10:54',('Author'),(+FILE_NAME('Open CASCADE Shape Model','2026-11-13T02:42:19',('Author'),(     'Open CASCADE'),'Open CASCADE STEP processor 7.9','Open CASCADE 7.9'   ,'Unknown'); FILE_SCHEMA(('AUTOMOTIVE_DESIGN { 1 0 10303 214 1 1 1 1 }'));