p24c08c-ssh-mir

@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "P24C08C-SSH-MIR",+    "manufacturer": "PUYA",+    "package": "SOP-8",+    "pin_count": 8,+    "category": "EEPROM",+    "parts": {+      "symbol": "p24c08c-ssh-mir.kicad_sym",+      "footprint": "p24c08c-ssh-mir.kicad_mod",+      "model_3d": "p24c08c-ssh-mir-etched.glb",+      "model_3d_plain": "p24c08c-ssh-mir.glb",+      "model_3d_step": "p24c08c-ssh-mir-etched.step",+      "model_3d_step_plain": "p24c08c-ssh-mir.step",+      "lbr": "p24c08c-ssh-mir.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect on P24C08C. Pin 1 is only used for the device address input E0 on the P24C02C variant; on P24C08C it is unbonded/internal-no-connect. Leave floating or tie to GND."+      },+      {+        "number": "2",+        "name": "NC",+        "type": "unconnected",+        "description": "No connect on P24C08C. Pin 2 is used as slave-address input E1 only on P24C02C and P24C04C; on P24C08C it is unbonded/internal-no-connect. Leave floating or tie to GND."+      },+      {+        "number": "3",+        "name": "E2",+        "type": "input",+        "description": "Device address input bit 2. Hardwired address selector used to distinguish devices on the same I2C bus; must match address bit A10 of the slave address. Internally pulled down to GND, so a floating pin selects address 0. Input capacitance 6 pF max."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Ground reference (0 V) for the device. Connect to the system ground plane; typically decoupled together with VCC using a 0.1 µF ceramic capacitor placed close to the package."+      },+      {+        "number": "5",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C bidirectional serial data line. Open-drain output that can be wire-ORed with other open-drain/collector devices on the bus; requires an external pull-up resistor to VCC (typ. 1.3 kΩ at 2.5-5.5 V, 10 kΩ at 1.7 V per Table 3-3). VOL ≤ 0.4 V @ IOL = 2.1 mA (VCC = 3 V). Input capacitance 8 pF max."+      },+      {+        "number": "6",+        "name": "SCL",+        "type": "input",+        "description": "I2C serial clock input. Positive edge clocks data into the device; negative edge clocks data out. Maximum clock frequency 1 MHz (VCC ≥ 2.5 V) or 400 kHz (1.7 V ≤ VCC < 2.5 V). Schmitt-trigger, filtered input; input capacitance 6 pF max."+      },+      {+        "number": "7",+        "name": "WCB",+        "type": "input",+        "description": "Write control (active-low). Tie to GND (or leave floating; internally pulled down to GND) to enable normal write operations. Drive high / tie to VCC to hardware-inhibit all writes to the memory array. Setup/hold times 0.6 µs (VCC ≥ 2.5 V) or 1.2 µs (< 2.5 V)."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply input. Operating range 1.7 V to 5.5 V for the -MI grade (this MPN). Read supply current 0.4 mA max @ 400 kHz; write supply current 1.6 mA max @ 400 kHz; standby 1 µA typ at 3.3 V/85 °C. Decouple with 0.1 µF close to the pin."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}