← Commit history
Publish 0.1.1
4 files changed
+405−11
oc5228-hero.glbadded⋯ 1 unchanged line ⋯
oc5228-hero.overlay.jsonadded+260@@ -0,0 +1,260 @@+{+ "spec": "adom-hero 1.4",+ "mpn": "OC5228",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+ "pad_outlines": {+ "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+ "rgba": [+ 0.0,+ 0.902,+ 0.863,+ 0.5+ ],+ "pads": 8,+ "span_mm": 6.9,+ "dash_mm": 0.1725,+ "gap_mm": 0.1035,+ "pad_stroke_mm": 0.0414+ },+ "silkscreen": {+ "material": "Silkscreen reference lines - 30 percent opacity",+ "rgba": [+ 0.92,+ 0.96,+ 1.0,+ 0.3+ ],+ "footprint_items": 7,+ "pin1": {+ "source": "footprint silkscreen",+ "pad": "1"+ }+ },+ "signal_names": {+ "material": "Signal names - 50 percent opacity",+ "rgba": [+ 0.92,+ 0.96,+ 1.0,+ 0.5+ ],+ "font": "DejaVu Sans Mono",+ "labels": 8,+ "sides": "top + mirrored underside (single-sided)",+ "fallback_to_pad_number": 0+ }+ },+ "align": {+ "ok": true,+ "centre_offset_mm": 0.0,+ "tolerance_mm": 0.552,+ "orientation_flipped": false,+ "contacts_bbox_mm": [+ -3.0,+ 3.0,+ -2.11,+ 2.11+ ],+ "pads_bbox_mm": [+ -3.45,+ 3.45,+ -2.205,+ 2.205+ ],+ "seating_z_mm": 0.0+ },+ "sources": {+ "glb": "oc5228-etched.glb",+ "glb_sha256": "8168f6ef3c1eae23653eca5bdcd695097b77bc95b3773d8ca317ecd857cca0fc",+ "footprint": "oc5228.kicad_mod",+ "footprint_sha256": "074ecb2092b24fa4b4b9cdd7c926fc587b0d7d6d21e7341e57935fd42d36894f",+ "pins": "page.json component.pins",+ "pins_sha256": "720c72f54668ed72d993c98410a6680d93850a3efead9556daf20c5de4acba9d"+ },+ "generator": "adom-wiki 1.8.28 (component_hero)",+ "labels": [+ {+ "pad": "1",+ "text": "LD",+ "x": -3.6,+ "y": -1.905,+ "align": "right",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "2",+ "text": "PWM",+ "x": -3.6,+ "y": -0.635,+ "align": "right",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "3",+ "text": "VDD",+ "x": -3.6,+ "y": 0.635,+ "align": "right",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "4",+ "text": "CS",+ "x": -3.6,+ "y": 1.905,+ "align": "right",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "5",+ "text": "D",+ "x": 3.6,+ "y": 1.905,+ "align": "left",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "6",+ "text": "D",+ "x": 3.6,+ "y": 0.635,+ "align": "left",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "7",+ "text": "GND",+ "x": 3.6,+ "y": -0.635,+ "align": "left",+ "vertical": false,+ "h": 0.6+ },+ {+ "pad": "8",+ "text": "GND",+ "x": 3.6,+ "y": -1.905,+ "align": "left",+ "vertical": false,+ "h": 0.6+ }+ ],+ "pads": [+ {+ "number": "1",+ "shape": "roundrect",+ "center_mm": [+ -2.475,+ -1.905+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "2",+ "shape": "roundrect",+ "center_mm": [+ -2.475,+ -0.635+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "3",+ "shape": "roundrect",+ "center_mm": [+ -2.475,+ 0.635+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "4",+ "shape": "roundrect",+ "center_mm": [+ -2.475,+ 1.905+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "5",+ "shape": "roundrect",+ "center_mm": [+ 2.475,+ 1.905+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "6",+ "shape": "roundrect",+ "center_mm": [+ 2.475,+ 0.635+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "7",+ "shape": "roundrect",+ "center_mm": [+ 2.475,+ -0.635+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ },+ {+ "number": "8",+ "shape": "roundrect",+ "center_mm": [+ 2.475,+ -1.905+ ],+ "size_mm": [+ 1.95,+ 0.6+ ],+ "rot": 0.0+ }+ ]+}
package.json+137−4@@ -1,6 +1,6 @@ { "slug": "oc5228",- "version": "0.1.0",+ "version": "0.1.1", "type": "component", "description": "OCX Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOP-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.", "tags": [@@ -24,6 +24,139 @@ "docs/hero.png", "docs/oc5228-datasheet.pdf", "viewers/symbol.html",- "viewers/footprint.html"- ]-}+ "viewers/footprint.html",+ "oc5228-etched.step",+ "oc5228-hero.glb",+ "oc5228-hero.overlay.json"+ ],+ "component": {+ "mpn": "OC5228",+ "manufacturer": "OCX",+ "package": "SOP-8",+ "pin_count": 8,+ "category": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",+ "parts": {+ "symbol": "oc5228.kicad_sym",+ "footprint": "oc5228.kicad_mod",+ "model_3d": "oc5228-hero.glb",+ "model_3d_plain": "oc5228.glb",+ "model_3d_step": "oc5228-etched.step",+ "model_3d_step_plain": "oc5228.step",+ "lbr": "oc5228.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "LD",+ "type": "input",+ "description": "Analog / segmented dimming control input. Floating = full brightness (high mode); tied to VDD = 1/2 current low-brightness mode; 0.2V-1.2V analog input sets output current (linear analog dimming); below 0.2V shuts output off. Can also accept PWM with high level > 1.2V. Internal 20uA pull-down (ILD_F) supports segmented dimming."+ },+ {+ "number": "2",+ "name": "PWM",+ "type": "input",+ "description": "PWM dimming input. High level enables output, low disables it; supports ultra-small duty ratios with a minimum response pulse width of 60ns. Rising threshold VPWM_H = 1.4V typ, falling VDIM_L = 0.8V typ. Pin floats to logic-high (output enabled) by default."+ },+ {+ "number": "3",+ "name": "VDD",+ "type": "power_in",+ "description": "Chip supply pin. Powered via an external bleeder resistor R3 from VIN; internally clamped by a 5.5V shunt (VDDCLAMP typ 5.5V, IDDCLAMP max 10mA). Startup occurs when VDD reaches ~4.1V. Requires >=1.0uF bypass capacitor placed close to the pin. Operating current IDD ~2.5mA at VDD = 5.5V; quiescent IVDDQ ~1.2mA."+ },+ {+ "number": "4",+ "name": "CS",+ "type": "input",+ "description": "Current-sense input. Connects to the source-side sense resistor Rcs; output current is regulated to Iout = 0.2V / Rcs. Constant-current reference VREF = 200mV typ (192-208mV); over-current threshold VCS = 216-264mV. Leading-edge blanking TLEB = 120ns typ. Absolute max VCS = -0.3 to 7.0V."+ },+ {+ "number": "5",+ "name": "D",+ "type": "output",+ "description": "Drain of the internal 100V / 2A power MOSFET (switching node). RDS(on) = 200 mOhm typ at VGS = 5.5V; VDS rating 100V. Pins 5 and 6 are tied together internally and both must be connected to the inductor / freewheel-diode switch node."+ },+ {+ "number": "6",+ "name": "D",+ "type": "output",+ "description": "Drain of the internal 100V / 2A power MOSFET (switching node), tied to pin 5. Connect both D pins together to the inductor / catch-diode node to share switch current."+ },+ {+ "number": "7",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground / power return. Pins 7 and 8 are both GND and should be tied together to the system ground plane close to the CS sense resistor to minimize sense-loop noise."+ },+ {+ "number": "8",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground / power return, tied to pin 7. Provides the return for internal control and MOS driver. Both GND pins must be connected on the board."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "distributor_links": {+ "digikey": false,+ "mouser": false+ },+ "distributor_check": {+ "checked_at": "2026-10-05T19:12:42Z",+ "source": "Component Ocean /api/assign-pns + lcsc_map",+ "digikey": {+ "pn": null,+ "status": "no match"+ },+ "mouser": {+ "pn": null,+ "status": "no match"+ }+ },+ "models_3d": [+ {+ "file": "oc5228.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "oc5228-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6,+ 4.9,+ 1.75+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "22e2ea204e3c24bfc8e39684143d13888488a39e3b6e3679150f74941c1ab855",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public"+}
page.json+8−7@@ -1,6 +1,6 @@ { "slug": "oc5228",- "version": "0.1.0",+ "version": "0.1.1", "type": "component", "description": "OCX Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOP-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.", "tags": [@@ -25,11 +25,11 @@ "docs/oc5228-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html",- "oc5228-etched.step"+ "oc5228-etched.step",+ "oc5228-hero.glb",+ "oc5228-hero.overlay.json" ],- "visibility": {- "public": true- },+ "visibility": "public", "author": { "name": "Ray" },@@ -161,5 +161,6 @@ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)" } ]- }-}+ },+ "org": "adom"+}