← Commit history

oc5228: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·3f1fc64fd5 · ·parent e6bbc42
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "OC5228",+    "manufacturer": "OCX",+    "package": "SOP-8",+    "pin_count": 8,+    "category": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",+    "parts": {+      "symbol": "oc5228.kicad_sym",+      "footprint": "oc5228.kicad_mod",+      "model_3d": "oc5228-etched.glb",+      "model_3d_plain": "oc5228.glb",+      "model_3d_step": "oc5228-etched.step",+      "model_3d_step_plain": "oc5228.step",+      "lbr": "oc5228.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "LD",+        "type": "input",+        "description": "Analog / segmented dimming control input. Floating = full brightness (high mode); tied to VDD = 1/2 current low-brightness mode; 0.2V-1.2V analog input sets output current (linear analog dimming); below 0.2V shuts output off. Can also accept PWM with high level > 1.2V. Internal 20uA pull-down (ILD_F) supports segmented dimming."+      },+      {+        "number": "2",+        "name": "PWM",+        "type": "input",+        "description": "PWM dimming input. High level enables output, low disables it; supports ultra-small duty ratios with a minimum response pulse width of 60ns. Rising threshold VPWM_H = 1.4V typ, falling VDIM_L = 0.8V typ. Pin floats to logic-high (output enabled) by default."+      },+      {+        "number": "3",+        "name": "VDD",+        "type": "power_in",+        "description": "Chip supply pin. Powered via an external bleeder resistor R3 from VIN; internally clamped by a 5.5V shunt (VDDCLAMP typ 5.5V, IDDCLAMP max 10mA). Startup occurs when VDD reaches ~4.1V. Requires >=1.0uF bypass capacitor placed close to the pin. Operating current IDD ~2.5mA at VDD = 5.5V; quiescent IVDDQ ~1.2mA."+      },+      {+        "number": "4",+        "name": "CS",+        "type": "input",+        "description": "Current-sense input. Connects to the source-side sense resistor Rcs; output current is regulated to Iout = 0.2V / Rcs. Constant-current reference VREF = 200mV typ (192-208mV); over-current threshold VCS = 216-264mV. Leading-edge blanking TLEB = 120ns typ. Absolute max VCS = -0.3 to 7.0V."+      },+      {+        "number": "5",+        "name": "D",+        "type": "output",+        "description": "Drain of the internal 100V / 2A power MOSFET (switching node). RDS(on) = 200 mOhm typ at VGS = 5.5V; VDS rating 100V. Pins 5 and 6 are tied together internally and both must be connected to the inductor / freewheel-diode switch node."+      },+      {+        "number": "6",+        "name": "D",+        "type": "output",+        "description": "Drain of the internal 100V / 2A power MOSFET (switching node), tied to pin 5. Connect both D pins together to the inductor / catch-diode node to share switch current."+      },+      {+        "number": "7",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground / power return. Pins 7 and 8 are both GND and should be tied together to the system ground plane close to the CS sense resistor to minimize sense-loop noise."+      },+      {+        "number": "8",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground / power return, tied to pin 7. Provides the return for internal control and MOS driver. Both GND pins must be connected on the board."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}