← Commit history

ncp1336bdr2g: factory component page (tier=lcsc)

Ray ·a3725a2d30 · ·parent 55ad3fe
2 files changed +33−36
README.md+15−15
@@ -8,20 +8,20 @@ NCP1336BDR2G from onsemi, in a SOIC-13. Pinout and pin descriptions extracted fr  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | OPP | input | Over Power Protection adjust. A negative voltage on this pin reduces the internal maximum peak current setpoint. Connect via a resistor divider from an auxiliary winding to perform Over Power compensation. Grounding disables OPP. Max operating voltage -300 mV. |-| 2 | OTP | input | Over-Temperature Protection input. Connect an NTC between this pin and GND. Pin sources an internal current that biases the NTC; when the NTC pulls the pin low, the controller permanently latches off. |-| 3 | Timer | passive | Timer duration setting. Wiring a capacitor from this pin to ground selects the fault timer duration used for short-circuit protection. |-| 4 | ZCD | input | Zero Crossing Detection. Connect to the auxiliary winding to sense the core reset (demag) event for quasi-resonant valley switching. Max continuous -0.3 to 10 V; pulsed +12 V for <100 us. |-| 5 | Ct | passive | Timing Capacitor. A capacitor on this pin acts as the timing capacitor used by the foldback (VCO) mode to set the switching frequency at light load. |-| 6 | FB | input | Feedback input. Hook an optocoupler collector to this pin to allow output regulation via the internal PWM comparator. |-| 7 | CS | input | Current Sense input. Monitors the primary MOSFET peak current via an external sense resistor for cycle-by-cycle current-mode control and OCP. |-| 8 | GND | power_in | Controller ground reference for all analog and digital circuitry. |-| 9 | DRV | output | Driver Output to the gate of an external power MOSFET. Peak source/sink capability -500 mA / +800 mA. Max output voltage VCC + 1.0 V when in high state. |-| 10 | VCC | power_in | Controller supply. Connect to an external auxiliary winding rectified voltage. Max continuous VCC = 28 V, max current +/-30 mA. |-| 11 | BO | input | Brownout input. Senses the bulk (input) voltage to stop switching when the mains falls below a set threshold, preventing operation under low-line conditions. |-| 12 | OVP | input | Over-Voltage Protection input. Pulling this pin high permanently latches off the controller for output OVP. |-| 13 | NC | unconnected | No connection. Pin is omitted from the die for improved creepage between the low-voltage side and the high-voltage HV pin (pin 14). |-| 14 | HV | power_in | High-Voltage startup input. Connect to the bulk capacitor; powers the internal high-voltage current source that delivers startup current to VCC. Rated -0.3 to 500 V, +/-20 mA. |+| 1 | OPP | input | Over Power Protection adjust. A negative voltage applied here reduces the internal maximum peak current setpoint. Connect via a resistor divider to an auxiliary winding for OPP compensation; ground to disable. Max negative operating voltage -300 mV. |+| 2 | OTP | input | Over-Temperature Protection input. Connect an NTC between this pin and GND; an internal current source biases the NTC. When the NTC pulls this pin down, the circuit permanently latches off. |+| 3 | Timer | passive | Fault timer duration select. Wiring a capacitor from this pin to ground sets the timer duration for fault handling. |+| 4 | ZCD | input | Zero Crossing / demagnetization Detection. Connected to the auxiliary winding (via a resistor) to detect the core reset event for quasi-resonant valley switching. Vmax -0.3 to +10 V DC, +12 V pulsed. |+| 5 | Ct | passive | Timing Capacitor. A capacitor from this pin to ground sets the frequency foldback timing (acts as the timing capacitor in foldback mode). |+| 6 | FB | input | Feedback pin. Connect the optocoupler collector here for output regulation via the internal pull-up. |+| 7 | CS | input | Current Sense input. Monitors the primary MOSFET peak current via the sense resistor for cycle-by-cycle current-mode control and OCP. |+| 8 | GND | power_in | Controller ground reference for all internal circuitry. |+| 9 | DRV | output | Gate driver output to the external power MOSFET. Peak source/sink capability -500 mA / +800 mA. Max voltage VCC + 1.0 V. |+| 10 | VCC | power_in | Supply pin for the controller, fed by the auxiliary winding after startup. Max continuous voltage 28 V, max current ±30 mA. |+| 11 | BO | input | Brownout input. Sensed against the bulk-rail resistor divider; stops circuit operation when mains input is too low. |+| 12 | OVP | input | Over-Voltage Protection input. Pulling this pin high permanently latches off the controller. |+| 13 | NC | unconnected | No connection. Pin is omitted from the package for improved creepage distance between HV (pin 14) and adjacent low-voltage pins. |+| 14 | HV | power_in | High-Voltage startup input. Connect to the bulk capacitor rail to power the internal high-voltage current source that delivers startup current to VCC. Voltage range -0.3 to 500 V. |  ## Key specifications @@ -46,7 +46,7 @@ NCP1336BDR2G from onsemi, in a SOIC-13. Pinout and pin descriptions extracted fr  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [onsemi datasheet](https://www.onsemi.com/pdf/datasheet/ncp1336b-d.pdf) (26 pp, sha256 `d28ee456f629ead0`, retrieved 2026-08-17, tier: manufacturer)+- **Datasheet:** [onsemi datasheet](docs/ncp1336bdr2g-datasheet.pdf) (26 pp, sha256 `d28ee456f629ead0`, retrieved 2026-08-17, tier: lcsc) - **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - **CAD:** KiCad official libraries (CC-BY-SA 4.0). 
page.json+18−21
@@ -18,7 +18,7 @@     "pin_count": 14,     "category": "PMIC",     "subcategory": "AC-DC Controllers and Regulators",-    "datasheet": "https://www.onsemi.com/pdf/datasheet/ncp1336b-d.pdf",+    "datasheet": "https://wmsc.lcsc.com/wmsc/upload/file/pdf/v2/lcsc/2003121414_onsemi-NCP1336BDR2G_C457724.pdf",     "parts": {       "symbol": "ncp1336bdr2g.kicad_sym",       "footprint": "ncp1336bdr2g.kicad_mod",@@ -32,94 +32,94 @@         "number": "1",         "name": "OPP",         "type": "input",-        "description": "Over Power Protection adjust. A negative voltage on this pin reduces the internal maximum peak current setpoint. Connect via a resistor divider from an auxiliary winding to perform Over Power compensation. Grounding disables OPP. Max operating voltage -300 mV."+        "description": "Over Power Protection adjust. A negative voltage applied here reduces the internal maximum peak current setpoint. Connect via a resistor divider to an auxiliary winding for OPP compensation; ground to disable. Max negative operating voltage -300 mV."       },       {         "number": "2",         "name": "OTP",         "type": "input",-        "description": "Over-Temperature Protection input. Connect an NTC between this pin and GND. Pin sources an internal current that biases the NTC; when the NTC pulls the pin low, the controller permanently latches off."+        "description": "Over-Temperature Protection input. Connect an NTC between this pin and GND; an internal current source biases the NTC. When the NTC pulls this pin down, the circuit permanently latches off."       },       {         "number": "3",         "name": "Timer",         "type": "passive",-        "description": "Timer duration setting. Wiring a capacitor from this pin to ground selects the fault timer duration used for short-circuit protection."+        "description": "Fault timer duration select. Wiring a capacitor from this pin to ground sets the timer duration for fault handling."       },       {         "number": "4",         "name": "ZCD",         "type": "input",-        "description": "Zero Crossing Detection. Connect to the auxiliary winding to sense the core reset (demag) event for quasi-resonant valley switching. Max continuous -0.3 to 10 V; pulsed +12 V for <100 us."+        "description": "Zero Crossing / demagnetization Detection. Connected to the auxiliary winding (via a resistor) to detect the core reset event for quasi-resonant valley switching. Vmax -0.3 to +10 V DC, +12 V pulsed."       },       {         "number": "5",         "name": "Ct",         "type": "passive",-        "description": "Timing Capacitor. A capacitor on this pin acts as the timing capacitor used by the foldback (VCO) mode to set the switching frequency at light load."+        "description": "Timing Capacitor. A capacitor from this pin to ground sets the frequency foldback timing (acts as the timing capacitor in foldback mode)."       },       {         "number": "6",         "name": "FB",         "type": "input",-        "description": "Feedback input. Hook an optocoupler collector to this pin to allow output regulation via the internal PWM comparator."+        "description": "Feedback pin. Connect the optocoupler collector here for output regulation via the internal pull-up."       },       {         "number": "7",         "name": "CS",         "type": "input",-        "description": "Current Sense input. Monitors the primary MOSFET peak current via an external sense resistor for cycle-by-cycle current-mode control and OCP."+        "description": "Current Sense input. Monitors the primary MOSFET peak current via the sense resistor for cycle-by-cycle current-mode control and OCP."       },       {         "number": "8",         "name": "GND",         "type": "power_in",-        "description": "Controller ground reference for all analog and digital circuitry."+        "description": "Controller ground reference for all internal circuitry."       },       {         "number": "9",         "name": "DRV",         "type": "output",-        "description": "Driver Output to the gate of an external power MOSFET. Peak source/sink capability -500 mA / +800 mA. Max output voltage VCC + 1.0 V when in high state."+        "description": "Gate driver output to the external power MOSFET. Peak source/sink capability -500 mA / +800 mA. Max voltage VCC + 1.0 V."       },       {         "number": "10",         "name": "VCC",         "type": "power_in",-        "description": "Controller supply. Connect to an external auxiliary winding rectified voltage. Max continuous VCC = 28 V, max current +/-30 mA."+        "description": "Supply pin for the controller, fed by the auxiliary winding after startup. Max continuous voltage 28 V, max current \u00b130 mA."       },       {         "number": "11",         "name": "BO",         "type": "input",-        "description": "Brownout input. Senses the bulk (input) voltage to stop switching when the mains falls below a set threshold, preventing operation under low-line conditions."+        "description": "Brownout input. Sensed against the bulk-rail resistor divider; stops circuit operation when mains input is too low."       },       {         "number": "12",         "name": "OVP",         "type": "input",-        "description": "Over-Voltage Protection input. Pulling this pin high permanently latches off the controller for output OVP."+        "description": "Over-Voltage Protection input. Pulling this pin high permanently latches off the controller."       },       {         "number": "13",         "name": "NC",         "type": "unconnected",-        "description": "No connection. Pin is omitted from the die for improved creepage between the low-voltage side and the high-voltage HV pin (pin 14)."+        "description": "No connection. Pin is omitted from the package for improved creepage distance between HV (pin 14) and adjacent low-voltage pins."       },       {         "number": "14",         "name": "HV",         "type": "power_in",-        "description": "High-Voltage startup input. Connect to the bulk capacitor; powers the internal high-voltage current source that delivers startup current to VCC. Rated -0.3 to 500 V, +/-20 mA."+        "description": "High-Voltage startup input. Connect to the bulk capacitor rail to power the internal high-voltage current source that delivers startup current to VCC. Voltage range -0.3 to 500 V."       }     ],     "provenance": {       "extractor": "ds2sf",       "datasheet": {-        "url": "https://www.onsemi.com/pdf/datasheet/ncp1336b-d.pdf",+        "url": "https://wmsc.lcsc.com/wmsc/upload/file/pdf/v2/lcsc/2003121414_onsemi-NCP1336BDR2G_C457724.pdf",         "pages": 26,         "sha256": "d28ee456f629ead0",-        "source_tier": "mfr"+        "source_tier": "lcsc"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {@@ -174,8 +174,5 @@     "docs/ncp1336bdr2g-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": {-    "public": true-  }+  ] }\ No newline at end of file