← Commit history
page.json+152−8@@ -1,13 +1,162 @@ {+ "schema_version": 1,+ "type": "component", "slug": "ncp1336bdr2g",+ "title": "NCP1336BDR2G",+ "brief": "onsemi AC-DC Controllers and Regulators, SOIC-13. Datasheet-verified pinout, KiCad symbol/footprint/3D.", "version": "0.1.0",- "type": "component",- "description": "onsemi AC-DC Controllers and Regulators, SOIC-13. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "license": "CC-BY-SA-4.0", "tags": [ "component", "pmic", "ncp1336bdr2g" ],+ "component": {+ "mpn": "NCP1336BDR2G",+ "manufacturer": "onsemi",+ "package": "SOIC-13",+ "pin_count": 14,+ "category": "PMIC",+ "subcategory": "AC-DC Controllers and Regulators",+ "datasheet": "https://www.onsemi.com/pdf/datasheet/ncp1336b-d.pdf",+ "parts": {+ "symbol": "ncp1336bdr2g.kicad_sym",+ "footprint": "ncp1336bdr2g.kicad_mod",+ "model_3d": "ncp1336bdr2g.glb",+ "model_3d_step": "ncp1336bdr2g.step",+ "lbr": "ncp1336bdr2g.lbr"+ },+ "distributor_links": {},+ "pins": [+ {+ "number": "1",+ "name": "OPP",+ "type": "input",+ "description": "Over Power Protection adjust. A negative voltage on this pin reduces the internal maximum peak current setpoint. Connect via a resistor divider from an auxiliary winding to perform Over Power compensation. Grounding disables OPP. Max operating voltage -300 mV."+ },+ {+ "number": "2",+ "name": "OTP",+ "type": "input",+ "description": "Over-Temperature Protection input. Connect an NTC between this pin and GND. Pin sources an internal current that biases the NTC; when the NTC pulls the pin low, the controller permanently latches off."+ },+ {+ "number": "3",+ "name": "Timer",+ "type": "passive",+ "description": "Timer duration setting. Wiring a capacitor from this pin to ground selects the fault timer duration used for short-circuit protection."+ },+ {+ "number": "4",+ "name": "ZCD",+ "type": "input",+ "description": "Zero Crossing Detection. Connect to the auxiliary winding to sense the core reset (demag) event for quasi-resonant valley switching. Max continuous -0.3 to 10 V; pulsed +12 V for <100 us."+ },+ {+ "number": "5",+ "name": "Ct",+ "type": "passive",+ "description": "Timing Capacitor. A capacitor on this pin acts as the timing capacitor used by the foldback (VCO) mode to set the switching frequency at light load."+ },+ {+ "number": "6",+ "name": "FB",+ "type": "input",+ "description": "Feedback input. Hook an optocoupler collector to this pin to allow output regulation via the internal PWM comparator."+ },+ {+ "number": "7",+ "name": "CS",+ "type": "input",+ "description": "Current Sense input. Monitors the primary MOSFET peak current via an external sense resistor for cycle-by-cycle current-mode control and OCP."+ },+ {+ "number": "8",+ "name": "GND",+ "type": "power_in",+ "description": "Controller ground reference for all analog and digital circuitry."+ },+ {+ "number": "9",+ "name": "DRV",+ "type": "output",+ "description": "Driver Output to the gate of an external power MOSFET. Peak source/sink capability -500 mA / +800 mA. Max output voltage VCC + 1.0 V when in high state."+ },+ {+ "number": "10",+ "name": "VCC",+ "type": "power_in",+ "description": "Controller supply. Connect to an external auxiliary winding rectified voltage. Max continuous VCC = 28 V, max current +/-30 mA."+ },+ {+ "number": "11",+ "name": "BO",+ "type": "input",+ "description": "Brownout input. Senses the bulk (input) voltage to stop switching when the mains falls below a set threshold, preventing operation under low-line conditions."+ },+ {+ "number": "12",+ "name": "OVP",+ "type": "input",+ "description": "Over-Voltage Protection input. Pulling this pin high permanently latches off the controller for output OVP."+ },+ {+ "number": "13",+ "name": "NC",+ "type": "unconnected",+ "description": "No connection. Pin is omitted from the die for improved creepage between the low-voltage side and the high-voltage HV pin (pin 14)."+ },+ {+ "number": "14",+ "name": "HV",+ "type": "power_in",+ "description": "High-Voltage startup input. Connect to the bulk capacitor; powers the internal high-voltage current source that delivers startup current to VCC. Rated -0.3 to 500 V, +/-20 mA."+ }+ ],+ "provenance": {+ "extractor": "ds2sf",+ "datasheet": {+ "url": "https://www.onsemi.com/pdf/datasheet/ncp1336b-d.pdf",+ "pages": 26,+ "sha256": "d28ee456f629ead0",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 14,+ "described": 14,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "metadata": {+ "specs": {+ "Manufacturer": "onsemi",+ "Package": "SOIC-13",+ "Category": "PMIC",+ "Pins": "14"+ }+ },+ "sections": [+ "hero",+ "viewers",+ "readme",+ "breadcrumbs",+ "info"+ ],+ "discovery_triggers": [+ "ncp1336bdr2g"+ ],+ "discovery_pitch": "NCP1336BDR2G (onsemi) component page with datasheet-verified CAD.",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }, "dependencies": {}, "hero": { "type": "image",@@ -25,10 +174,5 @@ "docs/ncp1336bdr2g-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ],- "visibility": "public",- "author": {- "name": "Ray",- "email": "[email protected]"- }+ ] }