← Commit history

Initial commit: component/ncl30125b2dr2g

Ray ·791fe5420a ·
2 files changed +92
README.mdadded+58
@@ -0,0 +1,58 @@+# NCL30125B2DR2G++**onsemi** · LED Drivers · SOIC-16++NCL30125B2DR2G from onsemi, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | HV | power_in | High-voltage startup pin (up to 700 V abs max). Connected to the rectified AC line or bulk rail through diodes/resistors to power the internal current source that charges the Vcc capacitor at startup (~11 mA typ) and supports Dynamic Self-Supply (DSS). |+| 2 | NC | unconnected | No connect. Pin position is omitted from the SOIC-16 package for improved creepage between the HV pin (pin 1) and the Fault pin (pin 3). |+| 3 | Fault | input | Combined latching OVP/OTP fault input. Controller latches off if VFault is pulled above VFault(OVP) = 2.5 V typ or below VFault(OTP) = 0.4 V typ. Provides a 50 uA pull-up current source (100 uA boosted during startup blanking) suitable for direct interface with an NTC thermistor. |+| 4 | BO | input | Brown-out and line-OVP sense input. Monitors a scaled version of the bulk/input voltage through a resistor divider. Controller starts pulsing when VBO > 0.80 V typ and stops after a 50 ms filter when VBO < 0.70 V typ; also provides a line-OVP shutdown above 2.9 V typ. |+| 5 | FB | input | Feedback input from the secondary-side regulation loop, typically driven by an optocoupler collector. Internally pulled up to VFB(ref) ~4.3 V through 11.6 kOhm. VFB is divided by KFB = 4 to set the peak current setpoint; skip mode is entered below Vskip = 0.3 V. |+| 6 | RT | input | Switching-frequency programming pin. A resistor to GND sets fSW between 50 kHz and 300 kHz (e.g. 200 kOhm -> 51 kHz, 100 kOhm -> 100 kHz, 32 kOhm -> 300 kHz). RRT = (1/fSW - 120 ns) * 1e10. |+| 7 | SS | output | Soft-start programming pin. External capacitor to GND is charged by an internal 5.2 uA current source; SS voltage divided by 4 clamps the CS peak-current setpoint until it reaches VSS = 2.0 V typ. Internally discharged on fault (OCP, UVLO, BO). |+| 8 | FW | output | Auxiliary gate-drive output for the bootstrap-refresh MOSFET (M3). Used to refresh the bootstrap capacitor during startup (tboot(start) ~ 200 us) and during skip mode. Peak +100 mA / -200 mA drive; clamped at ~12.7 V; max continuous current in high state limited to 10 mA. |+| 9 | CS | input | Primary current-sense input. Sets peak current via VILimit = 0.5 V typ, with a 2nd OCP threshold VCS(stop) = 0.75 V typ for abnormal overcurrent. Adaptive LEB (200-300 ns) and a 60 uA startup pull-up for open-pin detection. Also used to inject internal ramp compensation via internal 26.5 kOhm. |+| 10 | Vcc | power_in | Primary controller supply. VCC(on) = 16 V typ, VCC(min) = 10 V typ, VCC(off) = 8.8 V typ, absolute maximum 35 V. An internal OVP comparator trips at Vcc(OVP) = 25.9 V typ with 20 us blanking to protect against optocoupler faults. |+| 11 | GND | power_in | Controller ground return for all low-voltage circuitry and the DRV_LO/FW driver return path. |+| 12 | DRV_LO | output | Low-side MOSFET gate driver output. Peak +0.9 A / -1.2 A source/sink; ~13.5 V active clamp (16 V max) to protect the external MOSFET gate. 13 ns typ rise/fall into 1 nF. |+| 13 | NC | unconnected | No connect. Pin position is omitted from the SOIC-16 package for improved creepage between DRV_LO (pin 12) and DRV_HI (pin 14). |+| 14 | DRV_HI | output | High-side MOSFET gate driver output. Referenced to the HB pin and powered from Boot (floating bootstrap supply). Peak +0.9 A / -1.2 A source/sink; upper UVLO ensures adequate VGS before switching. |+| 15 | HB | passive | Half-bridge switching-node return for the high-side driver. Connects to the source of the high-side MOSFET / drain of the low-side MOSFET; serves as reference for DRV_HI and Boot. VBoot - VHB must not exceed 20 V. |+| 16 | Boot | power_in | Floating bootstrap supply for the high-side driver. External bootstrap capacitor tied between Boot and HB is refreshed via an external diode from Vcc and/or through the FW-driven refresh MOSFET. VBoot(on) = 8.5 V typ, VBoot(off) = 7.9 V typ, absolute max 620 V referenced to GND. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | onsemi |+| Package | SOIC-16 |+| Category | LED Drivers |+| Pins | 16 |++## Ordering variants++Same part, different packaging or reel option.++- `NCL30125B2DR2GA2DR2G`+- `NCL30125B2DR2G`++## CAD (KiCad official)++- Symbol: `NCL30125B2DR2G`+- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`+- 3D model: SOIC-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [onsemi datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8589998475783147520) (None pp, sha256 `7c36d2268817fc90`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ncl30125b2dr2g-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "ncl30125b2dr2g",+  "version": "0.1.0",+  "type": "component",+  "description": "onsemi LED Drivers, SOIC-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "led drivers",+    "ncl30125b2dr2g"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ncl30125b2dr2g.kicad_sym",+    "ncl30125b2dr2g.kicad_mod",+    "ncl30125b2dr2g.glb",+    "ncl30125b2dr2g.step",+    "ncl30125b2dr2g.lbr",+    "docs/hero.png",+    "docs/ncl30125b2dr2g-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file