← Commit history

Initial commit: component/mcp61s

Ray ·2905978d1b ·
2 files changed +98
README.mdadded+64
@@ -0,0 +1,64 @@+# MCP61S++**Mysentech** · Float Level Senors · QFN-24-EP(4x4)++MCP61S from Mysentech, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PA3 | bidirectional | General-purpose I/O port PA3. Standard TC-level I/O; input signal must not exceed VDD. Alternate functions: USART1_RX, USART2_SCK, SPI1_NSS; additional function: ADC1_VIN[2]. |+| 2 | PA14/NRST | bidirectional | General-purpose I/O port PA14. Standard TC-level I/O. Alternate functions: SWCLK, USART1_TX, SPI1_SCK. When RCC_SYSCFG SFT_NRST_RMP bit is set to 1, PA14 is remapped as NRST external reset input; reset low pulse must be at least 4 µs. |+| 3 | PB0/OSCIN | bidirectional | General-purpose I/O port PB0, also serves as external HSE clock input (OSCIN, up to 48 MHz). Standard TC-level I/O. Alternate function: USART2_SCK; additional function: ADC1_VIN[1]. |+| 4 | PA1 | bidirectional | General-purpose I/O port PA1. Standard TC-level I/O; input signal must not exceed VDD. Alternate functions: USART1_SCK, USART2_TX, I2C1_SDA, SPI1_MOSI. |+| 5 | VDD | power_in | Main digital power supply. Operating range 2.5 V to 5.5 V (typ. 3.3 V); absolute max 5.8 V. Decouple to GND near the pin. |+| 6 | PA15 | bidirectional | General-purpose I/O port PA15. Standard TC-level I/O. Alternate functions: SPI1_NSS, TIM1_CH3N, SPI1_MOSI, TIM3_CH3; additional function: ADC1_VIN[6]. |+| 7 | GND | power_in | Digital ground reference. Tie to system ground plane. |+| 8 | PA0 | bidirectional | General-purpose I/O port PA0. Standard TC-level I/O. Alternate functions: SPI1_NSS, USART1_RX, TIM1_CH3N, I2C1_SCL, TIM3_CH3. |+| 9 | PA4 | bidirectional | General-purpose I/O port PA4. Standard TC-level I/O. Alternate functions: TIM1_BKIN, I2C1_SDA, TIM3_CH4. |+| 10 | PA5 | bidirectional | General-purpose I/O port PA5. Standard TC-level I/O. Alternate functions: SPI1_SCK, TIM1_CH1N, I2C1_SCL. |+| 11 | GND | power_in | Digital ground reference. Tie to system ground plane. |+| 12 | VDDA | power_in | Analog power supply for the CAP-AFE and ADC. Same 2.5-5.5 V range as VDD; typically tied to VDD through an isolation filter for best analog performance. |+| 13 | GNDA | power_in | Analog ground reference for the CAP-AFE and ADC. Tie to the system ground plane (typically star-connected to GND). |+| 14 | C0N | input | Channel 0 capacitive sensor input, negative side of the differential pair. Connect together with C0P to the measured differential capacitor plates. |+| 15 | C0P | input | Channel 0 capacitive sensor input, positive side of the differential pair. Connect together with C0N to the measured differential capacitor plates (typ. sensor capacitance range 1-1000 pF). |+| 16 | VT | output | Temperature voltage output; a negative-temperature-coefficient voltage used with an external ADC (10-bit is sufficient) for approximate temperature measurement. Recommend a 1 nF external capacitor to GND for a ~1 ms settling time. |+| 17 | C1N | input | Channel 1 capacitive sensor input, negative side of the differential pair. Typically used for the reference capacitor of the ratiometric measurement. |+| 18 | C1P | input | Channel 1 capacitive sensor input, positive side of the differential pair. Typically used with C1N for the reference capacitor of the ratiometric measurement. |+| 19 | NC | unconnected | No connect. Leave floating or tie to GND per PCB practice. |+| 20 | RUP | bidirectional | External resistance pin for the CAP-AFE. Requires an external pull-up resistor (recommended 10 kΩ) to VDD per the typical application circuit. |+| 21 | PA10 | bidirectional | General-purpose I/O port PA10. Standard TC-level I/O. Alternate functions: SPI1_MISO, TIM1_CH3, TIM1_CH2, MCO (main clock output), USART1_TX. |+| 22 | PA13 | bidirectional | General-purpose I/O port PA13. Standard TC-level I/O. Alternate functions: SWDIO (serial-wire debug data), USART1_RX, USART2_RX, I2C1_SCL, SPI1_MISO. |+| 23 | PA2 | bidirectional | General-purpose I/O port PA2. Standard TC-level I/O. Alternate functions: TIM1_CH2N, SPI1_MISO, TIM3_CH2; additional function: ADC1_VIN[5]. |+| 24 | PA12 | bidirectional | General-purpose I/O port PA12. Standard TC-level I/O. Alternate function: USART1_TX; additional function: ADC1_VIN[3]. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Mysentech |+| Package | QFN-24-EP(4x4) |+| Category | Sensor |+| Pins | 24 |++## Ordering variants++- `MCP61S`++## CAD (KiCad official)++- Symbol: `MCP61S`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Mysentech datasheet](docs/mcp61s-datasheet.pdf) (None pp, sha256 `dfe28845be26d6c4`, retrieved 2026-08-17, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/mcp61s-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "mcp61s",+  "version": "0.1.0",+  "type": "component",+  "description": "Mysentech Float Level Senors, QFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "sensor",+    "mcp61s"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "mcp61s.kicad_sym",+    "mcp61s.kicad_mod",+    "mcp61s.glb",+    "mcp61s.step",+    "mcp61s.lbr",+    "docs/hero.png",+    "docs/mcp61s-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file