← Commit history

Initial commit: component/mcp251863t-e

Ray ·60bedd18b1 ·
2 files changed +102
README.mdadded+68
@@ -0,0 +1,68 @@+# MCP251863T-E++**Microchip** · CAN ICs · SSOP-28-208mil++MCP251863T-E from Microchip, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIO | power_in | Transceiver digital I/O supply. Sets the logic level for the digital I/O pins interfacing to the host MCU (TXD, RXD, STBY). |+| 2 | NC | unconnected | No connect. Leave floating or tie as recommended by design guidelines. |+| 3 | CANL | bidirectional | CAN bus low-level voltage I/O. Differential CAN bus line (low). Short-circuit and overtemperature protected. |+| 4 | CANH | bidirectional | CAN bus high-level voltage I/O. Differential CAN bus line (high). Short-circuit and overtemperature protected. |+| 5 | STBY | input | Transceiver standby mode control input. Drive high to place the transceiver into low-power standby mode; drive low for normal operation. |+| 6 | nINT1/GPIO1 | bidirectional | Configurable interrupt output (active-low) or general-purpose I/O pin. Function selected via controller registers. |+| 7 | nINT0/GPIO0/XSTBY | bidirectional | Configurable interrupt output (active-low), general-purpose I/O, or transceiver standby control (XSTBY) pin. Function selected via controller registers. |+| 8 | NC | unconnected | No connect. |+| 9 | SCK | input | SPI clock input from host MCU. Supports SPI clock up to 20 MHz in modes (0,0) and (1,1). |+| 10 | SDI | input | SPI data input (MOSI) from the host MCU. |+| 11 | SDO | output | SPI data output (MISO) to the host MCU. |+| 12 | NC | unconnected | No connect. |+| 13 | nCS | input | SPI chip-select input (active-low) from the host MCU. |+| 14 | VDD | power_in | Controller positive supply. Operating range 2.7 V to 5.5 V. Feeds the internal LDO / POR of the CAN FD controller die. |+| 15 | TXCAN | output | Transmit output of the internal CAN FD controller (routed internally to the transceiver TXD). |+| 16 | RXCAN | input | Receive input of the internal CAN FD controller (routed internally from the transceiver RXD). |+| 17 | NC | unconnected | No connect. |+| 18 | CLKO/SOF | output | Clock output / Start-of-Frame (test) output. Configurable as CAN clock output with prescaler or as SOF indicator. |+| 19 | nINT | output | Main interrupt output (active-low) from the CAN FD controller. Can be configured as push/pull or open-drain. |+| 20 | OSC2 | output | External crystal/resonator output. Connect to one terminal of a 40/20/4 MHz crystal or ceramic resonator (or leave open when using external clock on OSC1). |+| 21 | OSC1 | input | External crystal/resonator input, or external clock input. Supports 40, 20 or 4 MHz crystal/ceramic resonator or external clock. |+| 22 | VSS | power_in | Controller ground reference. |+| 23 | TXD | input | Transceiver transmit data input (internally driven from TXCAN in this integrated device). Includes TXD dominant time-out protection. |+| 24 | GND | power_in | Transceiver ground reference. |+| 25 | VCC | power_in | Transceiver positive supply (typically 5 V nominal for CAN transceiver operation). Undervoltage protected. |+| 26 | NC | unconnected | No connect. |+| 27 | NC | unconnected | No connect. |+| 28 | RXD | output | Transceiver receive data output (internally routed to RXCAN in this integrated device). Includes recessive clamping detection. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip |+| Package | SSOP-28-208mil |+| Category | Comm/UART |+| Pins | 28 |++## Ordering variants++- `MCP251863T-E/SS`+- `MCP251863T-EMCP251863-E/SS`++## CAD (KiCad official)++- Symbol: `MCP251863T-E`+- Footprint: `Package_SO:SSOP-28_5.3x10.2mm_P0.65mm`+- 3D model: SSOP-28-208mil (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip datasheet](docs/mcp251863t-e-datasheet.pdf) (106 pp, sha256 `88a35dc5bc412ca2`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/mcp251863t-e-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "mcp251863t-e",+  "version": "0.1.0",+  "type": "component",+  "description": "Microchip CAN ICs, SSOP-28-208mil. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "comm-uart",+    "mcp251863t-e"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "mcp251863t-e.kicad_sym",+    "mcp251863t-e.kicad_mod",+    "mcp251863t-e.glb",+    "mcp251863t-e.step",+    "mcp251863t-e.lbr",+    "docs/hero.png",+    "docs/mcp251863t-e-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file