← Commit history

mc78m18cdtrkg: factory component page (tier=mfr)

Ray ·f876caadad · ·parent 44aa020
4 files changed +45−53
README.md+6−6
@@ -8,10 +8,9 @@ MC78M18CDTRKG from onsemi, in a DPAK. Pinout and pin descriptions extracted from  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | Input | power_in | Unregulated DC input. Operating range for the 18 V option is approximately 21 V to 33 V (min 21 V to guarantee regulation, max 35 V absolute). Bypass with a small capacitor near the pin if the device is far from the bulk input filter capacitor. |-| 2 | Ground | power_in | Common ground reference for the input and output. The DPAK heatsink tab (pin 4) is internally connected to this pin, so the exposed pad is at ground potential and may be soldered directly to a ground copper pour for heatsinking. |-| 3 | Output | power_out | Regulated +18 V output, 500 mA max with adequate heatsinking (typ. 18.0 V, min 17.3 V, max 18.7 V at Tj = 25 °C). Internal short-circuit current limit ~350 mA, peak output current ~700 mA. A small output capacitor (e.g., 0.1 µF) is recommended to improve transient response. |-| 4 | Tab/Heatsink | passive | Exposed thermal tab on the back of the DPAK-3 body, shown as terminal 4 in the case outline. Internally connected to pin 2 (Ground). Solder to a ground copper area to conduct heat away; θJC ≈ 5 °C/W, θJA ≈ 92 °C/W for the DT suffix. |+| 1 | VI | power_in | Unregulated positive input voltage. Operating range 21 V to 33 Vdc for the 18 V option; absolute maximum 35 Vdc. An input bypass capacitor (typ. 0.33 µF) is recommended if the regulator is located far from the power-supply filter. |+| 2 | GND | power_in | Common ground reference for input and output. In the DPAK-3 (DT suffix) package the heatsink tab (mechanical terminal 4) is internally connected to Pin 2 (Ground). |+| 3 | VO | power_out | Regulated +18 V output. Nominal 18 V, min 17.3 V / max 18.7 V at Tj=25°C. Rated 500 mA continuous with adequate heatsinking; internally short-circuit current limited (typ. 350 mA at VI=35 V). A 0.1 µF output capacitor is recommended for transient response. |  ## Key specifications @@ -20,12 +19,13 @@ MC78M18CDTRKG from onsemi, in a DPAK. Pinout and pin descriptions extracted from | Manufacturer | onsemi | | Package | DPAK | | Category | PMIC |-| Pins | 4 |+| Pins | 3 |  ## Ordering variants  - `MC78M18CDTRKGDTRKG`-- `MC78M18CDTRKGDTRK`+- `MC78M18CDTRKGDT`+- `MC78M18CDTRKGT` - `MC78M18CDTRKGTG`  ## CAD (KiCad official)
mc78m18cdtrkg.kicad_sym+4−8
@@ -9,19 +9,15 @@     )     (symbol "MC78M18CDTRKG_1_1"     (pin power_in line (at -17.78 0.00 0) (length 5.08)-      (name "Input" (effects (font (size 1.27 1.27))))+      (name "VI" (effects (font (size 1.27 1.27))))       (number "1" (effects (font (size 1.27 1.27))))     )     (pin power_in line (at -17.78 -2.54 0) (length 5.08)-      (name "Ground" (effects (font (size 1.27 1.27))))+      (name "GND" (effects (font (size 1.27 1.27))))       (number "2" (effects (font (size 1.27 1.27))))     )-    (pin passive line (at 17.78 0.00 180) (length 5.08)-      (name "Tab/Heatsink" (effects (font (size 1.27 1.27))))-      (number "4" (effects (font (size 1.27 1.27))))-    )-    (pin power_out line (at 17.78 -2.54 180) (length 5.08)-      (name "Output" (effects (font (size 1.27 1.27))))+    (pin power_out line (at 17.78 0.00 180) (length 5.08)+      (name "VO" (effects (font (size 1.27 1.27))))       (number "3" (effects (font (size 1.27 1.27))))     )     )
mc78m18cdtrkg.lbr+24−19
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description>TO-252-2 (symbol synthesized from footprint pads)</description>+<description>onsemi Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, DPAK</description> <packages> <package name="TO-252-2">   <description>3 pads, 10.6 x 5.8 mm. TO-252/DPAK SMD package</description>@@ -87,33 +87,38 @@ </package> </packages> <symbols>-<symbol name="TO-252-2">-  <description>TO-252-2 (symbol synthesized from footprint pads)</description>-  <wire x1="-7.62" y1="3.81" x2="7.62" y2="3.81" width="0.254" layer="94"/>-  <wire x1="7.62" y1="3.81" x2="7.62" y2="-3.81" width="0.254" layer="94"/>-  <wire x1="7.62" y1="-3.81" x2="-7.62" y2="-3.81" width="0.254" layer="94"/>-  <wire x1="-7.62" y1="-3.81" x2="-7.62" y2="3.81" width="0.254" layer="94"/>-  <text x="0" y="6.35" size="1.27" layer="95" align="bottom-center">&gt;NAME</text>-  <text x="0" y="-6.35" size="1.27" layer="96" align="top-center">&gt;VALUE</text>-  <pin name="1" x="-12.7" y="2.54" length="short" direction="pas"/>-  <pin name="2" x="-12.7" y="0" length="short" direction="pas"/>-  <pin name="3" x="12.7" y="2.54" length="short" direction="pas" rot="R180"/>+<symbol name="MC78M18CDTRKG">+  <description>onsemi Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, DPAK</description>+  <wire x1="-12.7" y1="2.54" x2="12.7" y2="2.54" width="0.254" layer="94"/>+  <wire x1="12.7" y1="2.54" x2="12.7" y2="-5.08" width="0.254" layer="94"/>+  <wire x1="12.7" y1="-5.08" x2="-12.7" y2="-5.08" width="0.254" layer="94"/>+  <wire x1="-12.7" y1="-5.08" x2="-12.7" y2="2.54" width="0.254" layer="94"/>+  <text x="0.0000" y="5.0800" size="1.27" layer="95" align="center">&gt;NAME</text>+  <text x="0.0000" y="-7.6200" size="1.27" layer="96" align="center">&gt;VALUE</text>+  <pin name="VI" x="-17.78" y="0" length="middle" direction="pwr"/>+  <pin name="GND" x="-17.78" y="-2.54" length="middle" direction="pwr"/>+  <pin name="VO" x="17.78" y="0" length="middle" direction="out" rot="R180"/> </symbol> </symbols> <devicesets>-<deviceset name="TO-252-2" prefix="U">-  <description>TO-252-2 (symbol synthesized from footprint pads)</description>+<deviceset name="MC78M18CDTRKG" prefix="U">+  <description>onsemi Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, DPAK</description>   <gates>-    <gate name="G$1" symbol="TO-252-2" x="0" y="0"/>+    <gate name="G$1" symbol="MC78M18CDTRKG" x="0" y="0"/>   </gates>   <devices>     <device name="" package="TO-252-2">       <connects>-        <connect gate="G$1" pin="1" pad="1"/>-        <connect gate="G$1" pin="2" pad="2"/>-        <connect gate="G$1" pin="3" pad="3"/>+        <connect gate="G$1" pin="VI" pad="1"/>+        <connect gate="G$1" pin="GND" pad="2"/>+        <connect gate="G$1" pin="VO" pad="3"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="MC78M18CDTRKG" constant="no"/>+          <attribute name="MANUFACTURER" value="onsemi" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
page.json+11−20
@@ -15,7 +15,7 @@     "mpn": "MC78M18CDTRKG",     "manufacturer": "onsemi",     "package": "DPAK",-    "pin_count": 4,+    "pin_count": 3,     "category": "PMIC",     "subcategory": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",     "datasheet": "https://www.onsemi.com/pdf/datasheet/mc78m18cdtrk-d.pdf",@@ -30,27 +30,21 @@     "pins": [       {         "number": "1",-        "name": "Input",+        "name": "VI",         "type": "power_in",-        "description": "Unregulated DC input. Operating range for the 18 V option is approximately 21 V to 33 V (min 21 V to guarantee regulation, max 35 V absolute). Bypass with a small capacitor near the pin if the device is far from the bulk input filter capacitor."+        "description": "Unregulated positive input voltage. Operating range 21 V to 33 Vdc for the 18 V option; absolute maximum 35 Vdc. An input bypass capacitor (typ. 0.33 \u00b5F) is recommended if the regulator is located far from the power-supply filter."       },       {         "number": "2",-        "name": "Ground",+        "name": "GND",         "type": "power_in",-        "description": "Common ground reference for the input and output. The DPAK heatsink tab (pin 4) is internally connected to this pin, so the exposed pad is at ground potential and may be soldered directly to a ground copper pour for heatsinking."+        "description": "Common ground reference for input and output. In the DPAK-3 (DT suffix) package the heatsink tab (mechanical terminal 4) is internally connected to Pin 2 (Ground)."       },       {         "number": "3",-        "name": "Output",+        "name": "VO",         "type": "power_out",-        "description": "Regulated +18 V output, 500 mA max with adequate heatsinking (typ. 18.0 V, min 17.3 V, max 18.7 V at Tj = 25 °C). Internal short-circuit current limit ~350 mA, peak output current ~700 mA. A small output capacitor (e.g., 0.1 µF) is recommended to improve transient response."-      },-      {-        "number": "4",-        "name": "Tab/Heatsink",-        "type": "passive",-        "description": "Exposed thermal tab on the back of the DPAK-3 body, shown as terminal 4 in the case outline. Internally connected to pin 2 (Ground). Solder to a ground copper area to conduct heat away; θJC ≈ 5 °C/W, θJA ≈ 92 °C/W for the DT suffix."+        "description": "Regulated +18 V output. Nominal 18 V, min 17.3 V / max 18.7 V at Tj=25\u00b0C. Rated 500 mA continuous with adequate heatsinking; internally short-circuit current limited (typ. 350 mA at VI=35 V). A 0.1 \u00b5F output capacitor is recommended for transient response."       }     ],     "provenance": {@@ -63,8 +57,8 @@       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 4,-        "described": 4,+        "total": 3,+        "described": 3,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -79,7 +73,7 @@       "Manufacturer": "onsemi",       "Package": "DPAK",       "Category": "PMIC",-      "Pins": "4"+      "Pins": "3"     }   },   "sections": [@@ -114,8 +108,5 @@     "docs/mc78m18cdtrkg-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": {-    "public": true-  }+  ] }\ No newline at end of file