← Commit history

max823seuk-t: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)

Ray ·ec02081d93 · ·parent acd278b
2 files changed +89−9
package.json+47−7
@@ -53,31 +53,31 @@         "number": "1",         "name": "RESET",         "type": "output",-        "description": "Active-low reset output (push-pull); asserts low when VCC falls below the 2.93V threshold or MR is driven low, remains asserted for 200ms (typ, 140ms min) after VCC recovers; VOL \u2264 0.3V at ISINK = 1.2mA, VOH \u2265 0.8\u00d7VCC at ISOURCE = 30\u00b5A, guaranteed valid to VCC = 1V; ISOURCE short-circuit max 400\u00b5A."+        "description": "Active-low reset output (push-pull); asserts low when VCC falls below the 2.93V threshold or MR is driven low, remains asserted for 200ms (typ, 140ms min) after VCC recovers; VOL ≤ 0.3V at ISINK = 1.2mA, VOH ≥ 0.8×VCC at ISOURCE = 30µA, guaranteed valid to VCC = 1V; ISOURCE short-circuit max 400µA."       },       {         "number": "2",         "name": "GND",         "type": "power_in",-        "description": "Ground; all voltages referenced to this pin; supply current 5\u00b5A (typ), 12\u00b5A (max) for MAX823S in SOT23 with WDI and MR unconnected."+        "description": "Ground; all voltages referenced to this pin; supply current 5µA (typ), 12µA (max) for MAX823S in SOT23 with WDI and MR unconnected."       },       {         "number": "3",         "name": "MR",         "type": "input",-        "description": "Active-low manual reset input with internal 35-75k\u03a9 (typ 52k\u03a9) pullup to VCC; VIL \u2264 0.3\u00d7VCC, VIH \u2265 0.7\u00d7VCC; asserts RESET while held low and for 200ms after returning high; MR pulse width \u2265 1\u00b5s required; noise-immune to pulses \u2264 100ns; leave open or connect to VCC if unused."+        "description": "Active-low manual reset input with internal 35-75kΩ (typ 52kΩ) pullup to VCC; VIL ≤ 0.3×VCC, VIH ≥ 0.7×VCC; asserts RESET while held low and for 200ms after returning high; MR pulse width ≥ 1µs required; noise-immune to pulses ≤ 100ns; leave open or connect to VCC if unused."       },       {         "number": "4",         "name": "WDI",         "type": "input",-        "description": "Watchdog input; reset asserts if WDI remains continuously high or low beyond the watchdog timeout period (1.12s min, 1.60s typ, 2.40s max); timer cleared on any rising or falling edge or on RESET assertion; VIL \u2264 0.3\u00d7VCC, VIH \u2265 0.7\u00d7VCC; minimum pulse width 50ns; leave unconnected or tri-state driver to disable watchdog."+        "description": "Watchdog input; reset asserts if WDI remains continuously high or low beyond the watchdog timeout period (1.12s min, 1.60s typ, 2.40s max); timer cleared on any rising or falling edge or on RESET assertion; VIL ≤ 0.3×VCC, VIH ≥ 0.7×VCC; minimum pulse width 50ns; leave unconnected or tri-state driver to disable watchdog."       },       {         "number": "5",         "name": "VCC",         "type": "power_in",-        "description": "Positive supply voltage; operating range 1.0V to 5.5V (for MAX823S nominal range 3.0V to 3.6V per reset threshold); supply current 5\u00b5A (typ), 12\u00b5A (max) for MAX823T/S/R in SOT23; decouple with 0.1\u00b5F capacitor close to pin for transient immunity."+        "description": "Positive supply voltage; operating range 1.0V to 5.5V (for MAX823S nominal range 3.0V to 3.6V per reset threshold); supply current 5µA (typ), 12µA (max) for MAX823T/S/R in SOT23; decouple with 0.1µF capacitor close to pin for transient immunity."       }     ],     "provenance": {@@ -112,6 +112,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "max823seuk-t.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          2.8,+          2.9,+          1.55+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "720a6eab0024069bbee68e7cb4c3ff1149468a34611225cdc852662c5d0ec2b7",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "max823seuk-t-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          2.8,+          2.9,+          1.55+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "7180a6e750d323cde9e824aeb8e6b8622b25cdd2f84e4ac650f2e9f0a4def462",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}
page.json+42−2
@@ -97,7 +97,47 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "max823seuk-t.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          2.8,+          2.9,+          1.55+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "720a6eab0024069bbee68e7cb4c3ff1149468a34611225cdc852662c5d0ec2b7",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "max823seuk-t-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          2.8,+          2.9,+          1.55+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "7180a6e750d323cde9e824aeb8e6b8622b25cdd2f84e4ac650f2e9f0a4def462",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   },   "metadata": {     "specs": {@@ -145,4 +185,4 @@     "public": true   },   "updated_at": "2026-09-28T18:37:38.201Z"-}\ No newline at end of file+}