← Commit history

max813lcsa: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·b3c5fca9f8 · ·parent 06c9e04
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "MAX813LCSA",+    "manufacturer": "MSKSEMI",+    "package": "SOP-8",+    "pin_count": 8,+    "category": "Supervisor and Reset ICs",+    "parts": {+      "symbol": "max813lcsa.kicad_sym",+      "footprint": "max813lcsa.kicad_mod",+      "model_3d": "max813lcsa-etched.glb",+      "model_3d_plain": "max813lcsa.glb",+      "model_3d_step": "max813lcsa-etched.step",+      "model_3d_step_plain": "max813lcsa.step",+      "lbr": "max813lcsa.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "!MR",+        "type": "input",+        "description": "Active-low manual reset input. Internally pulled up to VCC through a 10-40 kΩ resistor (typ. 20 kΩ). Driving this pin low forces RESET active; input thresholds are 0.7·VCC / 0.6 V (VCC<4.5 V) or 2.0 V / 0.8 V (VCC≥4.5 V). Minimum low pulse width 150 ns (VCC>4.5 V) or 500 ns at lower supplies."+      },+      {+        "number": "2",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply input. Operating range 5.0 V-5.5 V for the 813L reset threshold (VRT = 4.65 V typ.); device functions down to 1.1 V for reset output validity. Supply current ICC ≈ 75 µA typical, 140 µA maximum."+      },+      {+        "number": "3",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground reference (0 V). Return for VCC and reference for all input/output thresholds."+      },+      {+        "number": "4",+        "name": "PFI",+        "type": "input",+        "description": "Power-fail comparator input, non-inverting side against an internal 1.25 V reference (threshold 1.20-1.30 V, typ. 1.25 V, on falling edge). Very high impedance input (±25 nA leakage). Tie to GND or VCC if unused; drive from an external resistor divider to monitor an arbitrary rail."+      },+      {+        "number": "5",+        "name": "!PFO",+        "type": "output",+        "description": "Active-low power-fail comparator output. Goes low when PFI drops below the 1.25 V reference. Push-pull drive: VOH ≥ VCC−1.5 V at 800 µA source (VCC≥4.5 V), VOL ≤ 0.4 V at 3.2 mA sink."+      },+      {+        "number": "6",+        "name": "WDI",+        "type": "input",+        "description": "Watchdog input. Must be toggled (high or low transition) at least every tWD ≈ 1.6 s typical (1.0-2.25 s) or !WDO will assert. Minimum pulse width tWP = 50 ns (VCC>4.5 V) or 100 ns at lower supplies. Leave floating (three-state / high-Z) to disable the watchdog timer."+      },+      {+        "number": "7",+        "name": "RESET",+        "type": "output",+        "description": "Active-high reset output. Asserts high whenever VCC falls below VRT (typ. 4.65 V) and remains high for tRS ≈ 200 ms after VCC recovers or after a manual reset. Push-pull drive: VOH ≥ VCC−1.5 V at 800 µA source (VCC≥4.5 V), VOL ≤ 0.4 V at 3.2 mA sink; guaranteed VOH ≥ 0.9 V even at VCC=1.2 V (ISOURCE=4 µA)."+      },+      {+        "number": "8",+        "name": "!WDO",+        "type": "output",+        "description": "Active-low watchdog timeout output. Pulls low if WDI is not toggled within tWD (~1.6 s). Push-pull drive: VOH ≥ VCC−1.5 V at 800 µA source (VCC≥4.5 V), VOL ≤ 0.4 V at 1.2 mA sink."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}