← Commit history

Initial commit: component/max20051aud

Ray ·a5f1a47e59 ·
2 files changed +94
README.mdadded+60
@@ -0,0 +1,60 @@+# MAX20051AUD++**Analog Devices Inc Maxim Integrated** · LED Drivers · TSSOP-14-EP++MAX20051AUD from Analog Devices Inc Maxim Integrated, in a TSSOP-14-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | PGND | power_in | Power ground for the integrated low-side MOSFET / buck converter power stage. Return path for the switching current; bypass IN to PGND with at least 1μF ceramic capacitor. |+| 2 | IN | power_in | Power-supply input, 4.5V to 65V. Feeds the internal buck power stage and the 5V VCC LDO. Bypass to PGND with a minimum of 1μF ceramic capacitor. Pins 2 and 3 are tied together internally. |+| 3 | IN | power_in | Power-supply input, 4.5V to 65V (second bond of the IN net for current handling). Tie externally to pin 2 and bypass to PGND with a minimum of 1μF ceramic capacitor. |+| 4 | CS+ | input | Positive input of the high-side average current-mode control amplifier. Connect to the junction of the output inductor and the top of the current-sense resistor. Common-mode range −0.2V to +65V; 200mV full-scale differential sense. |+| 5 | CS- | input | Negative input of the high-side average current-mode control amplifier. Connect to the anode of the LED string and to the other end of the current-sense resistor. Sets LED current together with CS+. |+| 6 | PWM | input | Logic-level PWM dimming input. Drive low to disable the current regulator, float or drive high for 100% duty. Absolute max −0.3V to +6V. If held low for >210ms the device turns off; also used to synchronize switching frequency. |+| 7 | FLT | output | Active-low, open-drain fault output. Pulled low to flag output overload, short-circuit, or overtemperature conditions (see Fault Pin Behavior). Requires external pull-up; absolute max −0.3V to +6V. |+| 8 | COMP | output | External loop compensation node (present on MAX20051/MAX20053 only). Connect an RC network from COMP to AGND to set the transconductance error-amplifier loop compensation. Voltage rating −0.3V to VCC+0.3V. |+| 9 | AGND | power_in | Analog ground reference for control circuitry, LDO, REFI, and COMP. Star-tie to PGND at the power-stage return. The exposed pad (EP) must be connected to AGND. |+| 10 | REFI | input | Analog dimming control input, 0 to 1.2V. Sets the full-scale LED current reference (200mV/CS_gain=5V/V typ). Below ~180mV the regulator zero-current threshold is reached and the output is disabled. Internally clamped to ~1.3V. |+| 11 | VCC | power_out | 5V internal LDO regulator output (10mA capable). Bias supply for the gate drivers and internal analog. Bypass to AGND with a 1μF ceramic capacitor. Do not load externally beyond spec. |+| 12 | BST | passive | Bootstrap capacitor node for the high-side MOSFET gate driver. Connect a 0.1μF ceramic capacitor from BST to LX. Absolute max BST-to-LX is 6V; BST-to-AGND is 75V (45V for C/D variants). |+| 13 | LX | power_out | Switching node - drain of internal high-side MOSFET and source of internal low-side MOSFET. Connect to one end of the output inductor. Pins 13 and 14 are internally tied and both must be connected together on the PCB. |+| 14 | LX | power_out | Switching node (second bond of the LX net for current handling, up to 2.1A). Tie externally to pin 13 and to the output inductor. |+| EP | EP | power_in | Exposed thermal pad on the bottom of the TSSOP-14-EP package. Connect to a large-area ground plane for effective power dissipation and tie to AGND. Do not use as the only ground connection. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Analog Devices Inc Maxim Integrated |+| Package | TSSOP-14-EP |+| Category | LED Drivers |+| Pins | 15 |++## Ordering variants++Same part, different packaging or reel option.++- `MAX20051AUD`+- `MAX20051AUDAAUD`+- `MAX20051AUDEAUD`+- `MAX20051AUDBAUD`+- `MAX20051AUDCAUD`++## CAD (KiCad official)++- Symbol: `MAX20051AUD`+- Footprint: `Package_SO:TSSOP-14-1EP_4.4x5mm_P0.65mm`+- 3D model: TSSOP-14-EP (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Analog Devices Inc Maxim Integrated datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8600615975394168832) (None pp, sha256 `bc10df94e5116eff`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/max20051aud-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "max20051aud",+  "version": "0.1.0",+  "type": "component",+  "description": "Analog Devices Inc Maxim Integrated LED Drivers, TSSOP-14-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "led drivers",+    "max20051aud"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "max20051aud.kicad_sym",+    "max20051aud.kicad_mod",+    "max20051aud.glb",+    "max20051aud.step",+    "max20051aud.lbr",+    "docs/hero.png",+    "docs/max20051aud-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file