← Commit history

m95040-wmn6tp: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·209d9c3660 · ·parent 0ccc819
1 file changed +75−1
page.json+75−1
@@ -33,5 +33,79 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "M95040-WMN6TP",+    "manufacturer": "STMicroelectronics",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "EEPROM",+    "datasheet": "https://www.st.com/resource/en/datasheet/m95040-wmn6tp.pdf",+    "parts": {+      "symbol": "m95040-wmn6tp.kicad_sym",+      "footprint": "m95040-wmn6tp.kicad_mod",+      "model_3d": "m95040-wmn6tp-etched.glb",+      "model_3d_plain": "m95040-wmn6tp.glb",+      "model_3d_step": "m95040-wmn6tp-etched.step",+      "model_3d_step_plain": "m95040-wmn6tp.step",+      "lbr": "m95040-wmn6tp.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "S",+        "type": "input",+        "description": "Chip Select (active-low). Driving S low selects the device and places it in Active Power mode; when S is high the device is deselected and Q is high-impedance. A falling edge on S is required after power-up before the first instruction; the S line should track VCC via a pull-up (typ. 100 kΩ) during power-up/down and must not float."+      },+      {+        "number": "2",+        "name": "Q",+        "type": "output",+        "description": "Serial Data Output (MISO). Data is shifted out MSB-first on the falling edge of Serial Clock (C). Output is high-impedance when the device is deselected or in the Hold condition."+      },+      {+        "number": "3",+        "name": "W",+        "type": "input",+        "description": "Write Protect (active-low). When W is held low, writes to the memory array (and to the Status Register when SRWD=1) are disabled while other operations remain enabled. W must be driven high or low - do not leave floating."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference for the VCC supply voltage. Connect to system ground; decouple VCC to VSS with ~10-100 nF close to the package pins."+      },+      {+        "number": "5",+        "name": "D",+        "type": "input",+        "description": "Serial Data Input (MOSI). Receives instructions, addresses, and write data MSB-first; values are latched on the rising edge of Serial Clock (C)."+      },+      {+        "number": "6",+        "name": "C",+        "type": "input",+        "description": "Serial Clock (SCK). Provides the timing for the serial interface; supports SPI modes (CPOL=0, CPHA=0) and (CPOL=1, CPHA=1) up to 20 MHz. D is sampled on the rising edge, Q changes on the falling edge. An external pull-down (typ. 100 kΩ) is recommended so C stays low if all SPI signals go high-impedance."+      },+      {+        "number": "7",+        "name": "HOLD",+        "type": "input",+        "description": "Hold (active-low). Pauses serial communication with the device without deselecting it: while HOLD is low with S also low, Q is high-impedance and D and C are Don't Care. To enter Hold, drive HOLD low while C is low; to exit, drive HOLD high while C is low. Must be driven high or low - do not leave floating."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage input, 2.5 V to 5.5 V for the -W voltage grade. Must be stable within [VCC(min), VCC(max)] before issuing instructions; a power-on-reset (POR) holds the device inactive until VCC crosses the VRES threshold. Decouple to VSS with ~10-100 nF close to the package."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}