← Commit history
page.json+15−12@@ -38,7 +38,7 @@ "number": "2", "name": "IREF", "type": "passive",- "description": "Pin for connecting an external resistor (approx. 180 k\u03a9 typical) that sets the constant current for internal circuits. Voltage at this pin is approximately 1.3 V."+ "description": "Pin for connecting an external resistor (approx. 180 kΩ typical) that sets the constant current for internal circuits. Voltage at this pin is approximately 1.3 V." }, { "number": "3",@@ -50,43 +50,43 @@ "number": "4", "name": "OFFC", "type": "passive",- "description": "Reset-time capacitor pin. Connect a capacitor (e.g. 0.33 \u03bcF for TW3\u224875 ms) that determines the restore time after a leakage event ends or after the SCR is triggered. Threshold ~2.4 V."+ "description": "Reset-time capacitor pin. Connect a capacitor (e.g. 0.33 μF for TW3≈75 ms) that determines the restore time after a leakage event ends or after the SCR is triggered. Threshold ~2.4 V." }, { "number": "5", "name": "TRC1", "type": "passive",- "description": "Capacitor pin for the 3-ms integrator that integrates the signal output from the leak-signal input-level discriminator. Threshold ~2.4 V; typical C=0.01 \u03bcF for TW1\u22483 ms."+ "description": "Capacitor pin for the 3-ms integrator that integrates the signal output from the leak-signal input-level discriminator. Threshold ~2.4 V; typical C=0.01 μF for TW1≈3 ms." }, { "number": "6", "name": "TRC2", "type": "passive",- "description": "Capacitor pin for the 1-ms noise-elimination integrator. Threshold ~2.4 V; typical C=0.0047 \u03bcF for TW2\u22481.5 ms."+ "description": "Capacitor pin for the 1-ms noise-elimination integrator. Threshold ~2.4 V; typical C=0.0047 μF for TW2≈1.5 ms." }, { "number": "7", "name": "DLYC", "type": "passive",- "description": "Delay-timer capacitor pin. Connect a capacitor (e.g. 1.0 \u03bcF for TW4\u2248300 ms) to set the delay time when using the delay function. Threshold ~2.4 V."+ "description": "Delay-timer capacitor pin. Connect a capacitor (e.g. 1.0 μF for TW4≈300 ms) to set the delay time when using the delay function. Threshold ~2.4 V." }, { "number": "8", "name": "SCRT", "type": "output",- "description": "SCR gate driver output. Sources high output current (IOH ~-50 \u03bcA typ. at TA=+20 \u00b0C, VO=8 V) to trigger the external SCR that fires the trip coil; low output voltage VOL\u22480.1 V at IOL=200 \u03bcA."+ "description": "SCR gate driver output. Sources high output current (IOH ~-50 μA typ. at TA=+20 °C, VO=8 V) to trigger the external SCR that fires the trip coil; low output voltage VOL≈0.1 V at IOL=200 μA." }, { "number": "9", "name": "VREF", "type": "output",- "description": "Reference-voltage output providing the input reference level for leakage detection. Nominal 2.4 V at IOH=-200 \u03bcA; VREF-to-GND clamp voltage 4.7 V at 5 mA."+ "description": "Reference-voltage output providing the input reference level for leakage detection. Nominal 2.4 V at IOH=-200 μA; VREF-to-GND clamp voltage 4.7 V at 5 mA." }, { "number": "10", "name": "ILKI", "type": "input",- "description": "Leakage-detection signal input (the other side of the differential leakage detector, referenced to VREF). DC input voltage of leakage detection \u00b114.0 mVdc w.r.t. VREF; total AC input VT=11.5 mVrms typ. at 60 Hz; input bias current ~220 nA."+ "description": "Leakage-detection signal input (the other side of the differential leakage detector, referenced to VREF). DC input voltage of leakage detection ±14.0 mVdc w.r.t. VREF; total AC input VT=11.5 mVrms typ. at 60 Hz; input bias current ~220 nA." }, { "number": "11",@@ -104,7 +104,7 @@ "number": "13", "name": "OPI-", "type": "input",- "description": "Inverting (negative) input of the internal operational amplifier. Differential input clamp \u00b10.8 V; differential input current limit \u00b15 mA; input bias current ~125 nA."+ "description": "Inverting (negative) input of the internal operational amplifier. Differential input clamp ±0.8 V; differential input current limit ±5 mA; input bias current ~125 nA." }, { "number": "14",@@ -116,13 +116,13 @@ "number": "15", "name": "OPI+", "type": "input",- "description": "Non-inverting (positive) input of the internal operational amplifier. Differential input clamp \u00b10.8 V vs. OPI-; input bias current ~125 nA."+ "description": "Non-inverting (positive) input of the internal operational amplifier. Differential input clamp ±0.8 V vs. OPI-; input bias current ~125 nA." }, { "number": "16", "name": "VS", "type": "power_in",- "description": "Main power supply input. Recommended operating range 7-12 V; absolute maximum 15 V. Standby supply current IS0=610 \u03bcA typ. at RIREF=180 k\u03a9."+ "description": "Main power supply input. Recommended operating range 7-12 V; absolute maximum 15 V. Standby supply current IS0=610 μA typ. at RIREF=180 kΩ." } ], "provenance": {@@ -200,5 +200,8 @@ "docs/m54133ag-s16-r-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }