component
M34E02-FDW6TP
Public Made by Adomby adom
STMicroelectronics EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+44@@ -0,0 +1,44 @@+# M34E02-FDW6TP++**STMicroelectronics** · EEPROM · TSSOP-8++M34E02-FDW6TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | E0 | input | Chip Enable input that sets bit b1 of the 7-bit device select code and must be connected directly to VCC or VSS; when unconnected an internal pull-down makes it 0, and it is also used to detect the VHV voltage when decoding an SWP or CWP instruction. |+| 2 | E1 | input | Chip Enable input that sets bit b2 of the 7-bit device select code and must be connected directly to VCC or VSS; when unconnected an internal pull-down makes it 0. |+| 3 | E2 | input | Chip Enable input that sets bit b3 of the 7-bit device select code and must be connected directly to VCC or VSS; when unconnected an internal pull-down makes it 0. |+| 4 | VSS | power_in | Ground reference for the device. |+| 5 | SDA | bidirectional | Open-drain serial data line used to transfer data in or out of the device, which may be wire-OR'ed with other open-drain or open-collector signals and requires a pull-up resistor to VCC. |+| 6 | SCL | input | Serial clock input that strobes all data in and out of the device; a pull-up to VCC is only needed if slave clock stretching is used, otherwise a push-pull bus master is sufficient. |+| 7 | WC | input | Write Control input that, when tied to VCC (for example), write-protects the entire memory area. |+| 8 | VCC | power_in | Supply voltage: 1.7 V to 5.5 V for temperature range 6 devices (1.7 V to 3.6 V for temperature range 1), with an absolute maximum of 6.5 V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | TSSOP-8 |+| Category | Memory |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `M34E02-FDW6TP`+- Footprint: `Package_SO:TSSOP-8_3x3mm_P0.65mm`+- 3D model: TSSOP-8 (KiCad packages3D, STEP)+- 3D model files: `m34e02-fdw6tp-etched.step` / `m34e02-fdw6tp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m34e02-fdw6tp.step` / `m34e02-fdw6tp.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588881543268220928) (36 pp, sha256 `67a2476224d1131e`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/m34e02-fdw6tp-datasheet.pdf)
page.jsonadded+200@@ -0,0 +1,200 @@+{+ "slug": "m34e02-fdw6tp",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "memory",+ "m34e02-fdw6tp",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "m34e02-fdw6tp.kicad_sym",+ "m34e02-fdw6tp.kicad_mod",+ "m34e02-fdw6tp.glb",+ "m34e02-fdw6tp.step",+ "m34e02-fdw6tp.lbr",+ "docs/hero.png",+ "docs/m34e02-fdw6tp-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "m34e02-fdw6tp-hero.glb",+ "m34e02-fdw6tp-hero.overlay.json"+ ],+ "component": {+ "mpn": "M34E02-FDW6TP",+ "manufacturer": "STMicroelectronics",+ "package": "TSSOP-8",+ "pin_count": 8,+ "category": "Memory",+ "subcategory": "EEPROM",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588881543268220928",+ "parts": {+ "symbol": "m34e02-fdw6tp.kicad_sym",+ "footprint": "m34e02-fdw6tp.kicad_mod",+ "model_3d": "m34e02-fdw6tp-hero.glb",+ "model_3d_plain": "m34e02-fdw6tp.glb",+ "model_3d_step": "m34e02-fdw6tp-etched.step",+ "model_3d_step_plain": "m34e02-fdw6tp.step",+ "lbr": "m34e02-fdw6tp.lbr"+ },+ "distributor_links": {+ "lcsc": "C283450",+ "digikey": "497-17907-2-ND",+ "mouser": "511-M34E02-FDW6TP"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T01:11:11Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-17907-2-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "511-M34E02-FDW6TP",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "E0",+ "type": "input",+ "description": "Chip Enable input that sets bit b1 of the 7-bit device select code and must be connected directly to VCC or VSS; when unconnected an internal pull-down makes it 0, and it is also used to detect the VHV voltage when decoding an SWP or CWP instruction."+ },+ {+ "number": "2",+ "name": "E1",+ "type": "input",+ "description": "Chip Enable input that sets bit b2 of the 7-bit device select code and must be connected directly to VCC or VSS; when unconnected an internal pull-down makes it 0."+ },+ {+ "number": "3",+ "name": "E2",+ "type": "input",+ "description": "Chip Enable input that sets bit b3 of the 7-bit device select code and must be connected directly to VCC or VSS; when unconnected an internal pull-down makes it 0."+ },+ {+ "number": "4",+ "name": "VSS",+ "type": "power_in",+ "description": "Ground reference for the device."+ },+ {+ "number": "5",+ "name": "SDA",+ "type": "bidirectional",+ "description": "Open-drain serial data line used to transfer data in or out of the device, which may be wire-OR'ed with other open-drain or open-collector signals and requires a pull-up resistor to VCC."+ },+ {+ "number": "6",+ "name": "SCL",+ "type": "input",+ "description": "Serial clock input that strobes all data in and out of the device; a pull-up to VCC is only needed if slave clock stretching is used, otherwise a push-pull bus master is sufficient."+ },+ {+ "number": "7",+ "name": "WC",+ "type": "input",+ "description": "Write Control input that, when tied to VCC (for example), write-protects the entire memory area."+ },+ {+ "number": "8",+ "name": "VCC",+ "type": "power_in",+ "description": "Supply voltage: 1.7 V to 5.5 V for temperature range 6 devices (1.7 V to 3.6 V for temperature range 1), with an absolute maximum of 6.5 V."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pin numbers were assigned from Figure 2 (TSSOP and MLP connections, top view), whose text layer is s; The datasheet only describes WC in prose (page 6) and in the signal table (page 7); it gives no elec"+ ],+ "pages_sent": 15,+ "cost_usd": 0.0669,+ "at": "2026-10-08T01:10:52"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588881543268220928",+ "pages": 36,+ "sha256": "67a2476224d1131e",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 8,+ "described": 8,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "m34e02-fdw6tp.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "cf28a51742b2e31065e201d1b313207140cbfb49062efd938788f7a310d02738",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "m34e02-fdw6tp-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 4.9,+ 3,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "858b8704114e1b4738dd6595377685bdf6b09ef1b83136ffecd8c4e74837cad7",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}