← Commit history

m24c32-wmn6tp: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·9dface7990 · ·parent ff3891e
1 file changed +75−1
page.json+75−1
@@ -33,5 +33,79 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "M24C32-WMN6TP",+    "manufacturer": "STMicroelectronics",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "EEPROM",+    "datasheet": "https://www.st.com/resource/en/datasheet/m24c32-wmn6tp.pdf",+    "parts": {+      "symbol": "m24c32-wmn6tp.kicad_sym",+      "footprint": "m24c32-wmn6tp.kicad_mod",+      "model_3d": "m24c32-wmn6tp-etched.glb",+      "model_3d_plain": "m24c32-wmn6tp.glb",+      "model_3d_step": "m24c32-wmn6tp-etched.step",+      "model_3d_step_plain": "m24c32-wmn6tp.step",+      "lbr": "m24c32-wmn6tp.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "E0",+        "type": "input",+        "description": "Chip Enable address input bit 0. Ties to VCC or VSS to set the LSB (b1) of the 7-bit I²C device select code, allowing up to eight M24C32 devices on the same bus. When left floating, this input is read as low (0)."+      },+      {+        "number": "2",+        "name": "E1",+        "type": "input",+        "description": "Chip Enable address input bit 1. Ties to VCC or VSS to set bit b2 of the 7-bit I²C device select code. When left floating, this input is read as low (0)."+      },+      {+        "number": "3",+        "name": "E2",+        "type": "input",+        "description": "Chip Enable address input bit 2 (MSB of the chip-enable field). Ties to VCC or VSS to set bit b3 of the 7-bit I²C device select code. When left floating, this input is read as low (0)."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference for VCC and all logic signals. Connect to the system ground plane."+      },+      {+        "number": "5",+        "name": "SDA",+        "type": "bidirectional",+        "description": "Serial Data - bidirectional, open-drain I²C data line. Transfers address and data bytes in both directions. Requires an external pull-up resistor to VCC (value depends on bus capacitance; see Figure 5)."+      },+      {+        "number": "6",+        "name": "SCL",+        "type": "input",+        "description": "Serial Clock - I²C clock input driven by the bus master; strobes all data in and out of the device. Supports 400 kHz fast-mode I²C. A pull-up to VCC is only required if a slave stretches the clock; otherwise a push-pull master output is sufficient."+      },+      {+        "number": "7",+        "name": "WC",+        "type": "input",+        "description": "Write Control (hardware write-protect). When driven high, write operations to the entire memory array are inhibited (device-select and address bytes are still ACKed, but data bytes are not ACKed). When low or left unconnected (internally read as VIL), writes are enabled."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage input, 2.5 V to 5.5 V for the M24C32-W variant. Decouple with a 10-100 nF capacitor placed close to the VCC/VSS pins. Device holds a power-on-reset (POR) until VCC crosses the POR threshold."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}