← Commit history

m24c08-wmn6p: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·185251f529 · ·parent 7575eec
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "M24C08-WMN6P",+    "manufacturer": "STMicroelectronics",+    "package": "SO-8",+    "pin_count": 8,+    "category": "EEPROM",+    "parts": {+      "symbol": "m24c08-wmn6p.kicad_sym",+      "footprint": "m24c08-wmn6p.kicad_mod",+      "model_3d": "m24c08-wmn6p-etched.glb",+      "model_3d_plain": "m24c08-wmn6p.glb",+      "model_3d_step": "m24c08-wmn6p-etched.step",+      "model_3d_step_plain": "m24c08-wmn6p.step",+      "lbr": "m24c08-wmn6p.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "NC",+        "type": "unconnected",+        "description": "Not connected. In the SO8/TSSOP8/PDIP8/UFDFPN8 8-lead M24C08, pin 1 is unused (reserved / no internal bond). May be left floating or tied to VSS."+      },+      {+        "number": "2",+        "name": "NC",+        "type": "unconnected",+        "description": "Not connected. In the SO8/TSSOP8/PDIP8/UFDFPN8 8-lead M24C08, pin 2 is unused. May be left floating or tied to VSS."+      },+      {+        "number": "3",+        "name": "E2",+        "type": "input",+        "description": "Chip Enable address input. Sets the value of bit b3 of the I2C device select code (1010 E2 A9 A8 R/W), allowing up to two M24C08 devices to share the same I2C bus. Must be tied to VCC or VSS; if left floating it is read as 0."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference for VCC and all logic signals. 0 V."+      },+      {+        "number": "5",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I2C Serial Data input/output. Open-drain output - an external pull-up resistor from SDA to VCC is required (typical 1 kΩ-10 kΩ depending on bus capacitance and speed; see Figure 13 for Rbus vs. Cbus at 400 kHz)."+      },+      {+        "number": "6",+        "name": "SCL",+        "type": "input",+        "description": "I2C Serial Clock input. Strobes data available on SDA(in) and clocks out data on SDA(out). Supports 100 kHz standard-mode and 400 kHz fast-mode I2C."+      },+      {+        "number": "7",+        "name": "WC",+        "type": "input",+        "description": "Write Control (write protect). When driven high, the entire memory array is protected: device select and address bytes are acknowledged but data bytes are NoAck'd and no write occurs. Write operations are enabled when WC is driven low or left floating (internal pull-down / read as 0)."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Positive supply voltage. For the -W variant: 2.5 V to 5.5 V operating range. Decouple to VSS with a 10 nF-100 nF capacitor close to the package."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}