← Commit history
m24128-brmn6tp: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+75−1
page.json+75−1@@ -33,5 +33,79 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "M24128-BRMN6TP",+ "manufacturer": "STMicroelectronics",+ "package": "SOIC-8",+ "pin_count": 8,+ "category": "EEPROM",+ "datasheet": "https://www.st.com/resource/en/datasheet/m24128-brmn6tp.pdf",+ "parts": {+ "symbol": "m24128-brmn6tp.kicad_sym",+ "footprint": "m24128-brmn6tp.kicad_mod",+ "model_3d": "m24128-brmn6tp-etched.glb",+ "model_3d_plain": "m24128-brmn6tp.glb",+ "model_3d_step": "m24128-brmn6tp-etched.step",+ "model_3d_step_plain": "m24128-brmn6tp.step",+ "lbr": "m24128-brmn6tp.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "E0",+ "type": "input",+ "description": "Chip Enable address bit 0. Tie to VCC or VSS to set bit b1 of the 7-bit I2C device select code (1010 E2 E1 E0). Left floating, it is read as 0. Allows up to 8 devices to share the bus."+ },+ {+ "number": "2",+ "name": "E1",+ "type": "input",+ "description": "Chip Enable address bit 1. Tie to VCC or VSS to set bit b2 of the 7-bit I2C device select code. Left floating, it is read as 0."+ },+ {+ "number": "3",+ "name": "E2",+ "type": "input",+ "description": "Chip Enable address bit 2. Tie to VCC or VSS to set bit b3 of the 7-bit I2C device select code. Left floating, it is read as 0."+ },+ {+ "number": "4",+ "name": "VSS",+ "type": "power_in",+ "description": "Ground reference for the VCC supply voltage. 0 V."+ },+ {+ "number": "5",+ "name": "SDA",+ "type": "bidirectional",+ "description": "Serial Data input/output. Open-drain output; requires an external pull-up resistor to VCC. Transfers data in and out of the device on the I2C bus."+ },+ {+ "number": "6",+ "name": "SCL",+ "type": "input",+ "description": "Serial Clock input. Strobes data on SDA(in) and clocks SDA(out). Supports 100 kHz, 400 kHz, and 1 MHz I2C bus modes."+ },+ {+ "number": "7",+ "name": "WC",+ "type": "input",+ "description": "Write Control input. Drive high to inhibit all write operations to the memory array (device ACKs select/address bytes but NACKs data bytes). Drive low or leave floating to enable writes."+ },+ {+ "number": "8",+ "name": "VCC",+ "type": "power_in",+ "description": "Supply voltage. 1.8 V to 5.5 V for the -BR variant. Decouple to VSS with a 10 nF to 100 nF capacitor placed close to the package."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}