component
LSM6DSRXTR
Public Made by Adomby adom
STMicroelectronics Accelerometers, LGA-14(2.5x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+50@@ -0,0 +1,50 @@+# LSM6DSRXTR++**STMicroelectronics** · Accelerometers · LGA-14(2.5x3)++LSM6DSRXTR from STMicroelectronics, in a LGA-14(2.5x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SDO/SA0 | bidirectional | Serial data output (SDO) for SPI 4-wire, and the I²C least significant address bit (SA0), which gives address 1101011b when tied to Vdd_IO and 1101010b when tied to GND. |+| 2 | SDx | bidirectional | Must be connected to Vdd_IO or GND in Mode 1, carries the I²C master serial data (MSDA) in Mode 2, and carries the auxiliary SPI serial data input (SDI) and 3-wire SDO in Modes 3/4; it has no internal pull-up unless SHUB_PU_EN = 1. |+| 3 | SCx | bidirectional | Must be connected to Vdd_IO or GND in Mode 1, carries the I²C master serial clock (MSCL) in Mode 2, and carries the auxiliary SPI serial port clock (SPC_Aux) in Modes 3/4. |+| 4 | INT1 | bidirectional | Programmable interrupt 1 output; it must be set to Vdd_IO when used as a MIPI I3CSM pure slave, and when left floating it has an internal pull-down and I²C/I3C are both active. |+| 5 | Vdd_IO | power_in | Power supply for the I/O pins, with a 100 nF filter capacitor recommended. |+| 6 | GND | power_in | 0 V supply. |+| 7 | GND | power_in | 0 V supply. |+| 8 | Vdd | power_in | Analog power supply, specified at 1.71 V to 3.6 V, with 100 nF decoupling capacitor placed as close to the pin as possible. |+| 9 | INT2 | bidirectional | Programmable interrupt 2 (INT2) or data enable (DEN); in Mode 2 it also serves as the I²C master external synchronization signal (MDRDY), and by default its output is forced to ground. |+| 10 | OCS_Aux | input | Leave unconnected in Modes 1 and 2; in Modes 3 and 4 it is the auxiliary SPI 3/4-wire interface enable, with no internal pull-up by default. |+| 11 | SDO_Aux | output | Connect to Vdd_IO or leave unconnected in Modes 1 and 2; in Mode 3 (3-wire aux SPI) leave unconnected, and in Mode 4 it is the auxiliary SPI 4-wire serial data output (SDO_Aux). |+| 12 | CS | input | I²C/SPI mode selection: 1 selects SPI idle mode with I²C communication enabled, and 0 selects SPI communication mode with I²C disabled; default has an internal pull-up. |+| 13 | SCL | bidirectional | I²C/MIPI I3CSM serial clock (SCL) or SPI serial port clock (SPC) in all modes; for I²C it must be pulled up to Vdd_IO through external resistors. |+| 14 | SDA | bidirectional | I²C/MIPI I3CSM serial data (SDA), SPI serial data input (SDI), or 3-wire SPI serial data output (SDO); for I²C it must be pulled up to Vdd_IO through an external resistor. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LGA-14(2.5x3) |+| Category | Sensors |+| Pins | 14 |++## CAD (KiCad official)++- Symbol: `LSM6DSRXTR`+- Footprint: `Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm`+- 3D model: LGA-14(2.5x3) (KiCad packages3D, STEP)+- 3D model files: `lsm6dsrxtr-etched.step` / `lsm6dsrxtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lsm6dsrxtr.step` / `lsm6dsrxtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590445411237326848) (171 pp, sha256 `11f685646ff7174a`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lsm6dsrxtr-datasheet.pdf)
page.jsonadded+238@@ -0,0 +1,238 @@+{+ "slug": "lsm6dsrxtr",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics Accelerometers, LGA-14(2.5x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "sensors",+ "lsm6dsrxtr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lsm6dsrxtr.kicad_sym",+ "lsm6dsrxtr.kicad_mod",+ "lsm6dsrxtr.glb",+ "lsm6dsrxtr.step",+ "lsm6dsrxtr.lbr",+ "docs/hero.png",+ "docs/lsm6dsrxtr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "lsm6dsrxtr-hero.glb",+ "lsm6dsrxtr-hero.overlay.json"+ ],+ "component": {+ "mpn": "LSM6DSRXTR",+ "manufacturer": "STMicroelectronics",+ "package": "LGA-14(2.5x3)",+ "pin_count": 14,+ "category": "Sensors",+ "subcategory": "Accelerometers",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590445411237326848",+ "parts": {+ "symbol": "lsm6dsrxtr.kicad_sym",+ "footprint": "lsm6dsrxtr.kicad_mod",+ "model_3d": "lsm6dsrxtr-hero.glb",+ "model_3d_plain": "lsm6dsrxtr.glb",+ "model_3d_step": "lsm6dsrxtr-etched.step",+ "model_3d_step_plain": "lsm6dsrxtr.step",+ "lbr": "lsm6dsrxtr.lbr"+ },+ "distributor_links": {+ "lcsc": "C2970339",+ "digikey": "497-LSM6DSRXTR-ND",+ "mouser": "511-LSM6DSRXTR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T00:33:30Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-LSM6DSRXTR-ND",+ "status": "found",+ "lifecycle": "Last Time Buy"+ },+ "mouser": {+ "pn": "511-LSM6DSRXTR",+ "status": "found",+ "lifecycle": "End of Life"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "SDO/SA0",+ "type": "bidirectional",+ "description": "Serial data output (SDO) for SPI 4-wire, and the I²C least significant address bit (SA0), which gives address 1101011b when tied to Vdd_IO and 1101010b when tied to GND."+ },+ {+ "number": "2",+ "name": "SDx",+ "type": "bidirectional",+ "description": "Must be connected to Vdd_IO or GND in Mode 1, carries the I²C master serial data (MSDA) in Mode 2, and carries the auxiliary SPI serial data input (SDI) and 3-wire SDO in Modes 3/4; it has no internal pull-up unless SHUB_PU_EN = 1."+ },+ {+ "number": "3",+ "name": "SCx",+ "type": "bidirectional",+ "description": "Must be connected to Vdd_IO or GND in Mode 1, carries the I²C master serial clock (MSCL) in Mode 2, and carries the auxiliary SPI serial port clock (SPC_Aux) in Modes 3/4."+ },+ {+ "number": "4",+ "name": "INT1",+ "type": "bidirectional",+ "description": "Programmable interrupt 1 output; it must be set to Vdd_IO when used as a MIPI I3CSM pure slave, and when left floating it has an internal pull-down and I²C/I3C are both active."+ },+ {+ "number": "5",+ "name": "Vdd_IO",+ "type": "power_in",+ "description": "Power supply for the I/O pins, with a 100 nF filter capacitor recommended."+ },+ {+ "number": "6",+ "name": "GND",+ "type": "power_in",+ "description": "0 V supply."+ },+ {+ "number": "7",+ "name": "GND",+ "type": "power_in",+ "description": "0 V supply."+ },+ {+ "number": "8",+ "name": "Vdd",+ "type": "power_in",+ "description": "Analog power supply, specified at 1.71 V to 3.6 V, with 100 nF decoupling capacitor placed as close to the pin as possible."+ },+ {+ "number": "9",+ "name": "INT2",+ "type": "bidirectional",+ "description": "Programmable interrupt 2 (INT2) or data enable (DEN); in Mode 2 it also serves as the I²C master external synchronization signal (MDRDY), and by default its output is forced to ground."+ },+ {+ "number": "10",+ "name": "OCS_Aux",+ "type": "input",+ "description": "Leave unconnected in Modes 1 and 2; in Modes 3 and 4 it is the auxiliary SPI 3/4-wire interface enable, with no internal pull-up by default."+ },+ {+ "number": "11",+ "name": "SDO_Aux",+ "type": "output",+ "description": "Connect to Vdd_IO or leave unconnected in Modes 1 and 2; in Mode 3 (3-wire aux SPI) leave unconnected, and in Mode 4 it is the auxiliary SPI 4-wire serial data output (SDO_Aux)."+ },+ {+ "number": "12",+ "name": "CS",+ "type": "input",+ "description": "I²C/SPI mode selection: 1 selects SPI idle mode with I²C communication enabled, and 0 selects SPI communication mode with I²C disabled; default has an internal pull-up."+ },+ {+ "number": "13",+ "name": "SCL",+ "type": "bidirectional",+ "description": "I²C/MIPI I3CSM serial clock (SCL) or SPI serial port clock (SPC) in all modes; for I²C it must be pulled up to Vdd_IO through external resistors."+ },+ {+ "number": "14",+ "name": "SDA",+ "type": "bidirectional",+ "description": "I²C/MIPI I3CSM serial data (SDA), SPI serial data input (SDI), or 3-wire SPI serial data output (SDO); for I²C it must be pulled up to Vdd_IO through an external resistor."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pin functions are mode-dependent (Mode 1, Mode 2, Mode 3/4). The pin names above are the primary fun; Operating voltage range for Vdd_IO is not in the supplied excerpt (it is in Table 3 on a page not in; Pin 1 (SDO/SA0) and pins 2, 3, 4, 9, 13, 14 are typed bidirectional because they change direction or",+ "1/14 pins cited to the wrong page (name found elsewhere): ['8:Vdd@p1']"+ ],+ "pages_sent": 29,+ "cost_usd": 0.1285,+ "at": "2026-10-08T00:33:15"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8590445411237326848",+ "pages": 171,+ "sha256": "11f685646ff7174a",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 14,+ "described": 14,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lsm6dsrxtr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.5,+ 0.78+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "a441fc384db400c96db6affec2f9c22a5d76b0729e0f2fc46c53746be60b76ca",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lsm6dsrxtr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.5,+ 0.78+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "aee5d84b5b2e17ce927f10fd2a7cdc1a4992caf69629f4d70b7b80cd9ee303ad",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}