← Commit history
Publish 0.2.1
4 files changed
+588−11
lsm6dsotr-hero.glbadded⋯ 1 unchanged line ⋯
lsm6dsotr-hero.overlay.jsonadded+392@@ -0,0 +1,392 @@+{+ "spec": "adom-hero 1.4",+ "mpn": "LSM6DSOTR",+ "kind": "component + footprint reference art",+ "board_use": false,+ "plane_z_mm": -0.02,+ "units": "metre",+ "upAxis": "Z",+ "layers": {+ "pad_outlines": {+ "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+ "rgba": [+ 0.0,+ 0.902,+ 0.863,+ 0.5+ ],+ "pads": 14,+ "span_mm": 3.2,+ "dash_mm": 0.12,+ "gap_mm": 0.072,+ "pad_stroke_mm": 0.03+ },+ "silkscreen": {+ "material": "Silkscreen reference lines - 30 percent opacity",+ "rgba": [+ 0.92,+ 0.96,+ 1.0,+ 0.3+ ],+ "footprint_items": 8,+ "pin1": {+ "source": "footprint silkscreen",+ "pad": "1"+ }+ },+ "signal_names": {+ "material": "Signal names - 50 percent opacity",+ "rgba": [+ 0.92,+ 0.96,+ 1.0,+ 0.5+ ],+ "font": "DejaVu Sans Mono",+ "labels": 14,+ "sides": "top + mirrored underside (single-sided)",+ "fallback_to_pad_number": 0+ }+ },+ "align": {+ "ok": true,+ "centre_offset_mm": 0.0,+ "tolerance_mm": 0.256,+ "orientation_flipped": false,+ "contacts_bbox_mm": [+ -1.5,+ 1.5,+ -1.25,+ 1.25+ ],+ "pads_bbox_mm": [+ -1.6,+ 1.6,+ -1.35,+ 1.35+ ],+ "seating_z_mm": -0.0+ },+ "sources": {+ "glb": "lsm6dsotr-etched.glb",+ "glb_sha256": "7723995f392089cb5768a3b79745c469d7ff1c1a741794da1e87c2473cfab9b0",+ "footprint": "lsm6dsotr.kicad_mod",+ "footprint_sha256": "9b49bc488c35f69dfddda4ee586cfe4f092339d33464cf061518dd68c342b369",+ "pins": "page.json component.pins",+ "pins_sha256": "1f0c380fe397d46fa8505c9c42a2b36c9b1e0583429861667b63b9e8e6607d0c"+ },+ "generator": "adom-wiki 1.8.31 (component_hero)",+ "labels": [+ {+ "pad": "1",+ "text": "SDO/SA0",+ "x": -1.7,+ "y": -0.75,+ "align": "right",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "2",+ "text": "SDx",+ "x": -1.7,+ "y": -0.25,+ "align": "right",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "3",+ "text": "SCx",+ "x": -1.7,+ "y": 0.25,+ "align": "right",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "4",+ "text": "INT1",+ "x": -1.7,+ "y": 0.75,+ "align": "right",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "5",+ "text": "VDDIO",+ "x": -0.5,+ "y": 1.45,+ "align": "right",+ "vertical": true,+ "h": 0.25+ },+ {+ "pad": "6",+ "text": "GND",+ "x": 0.0,+ "y": 1.45,+ "align": "right",+ "vertical": true,+ "h": 0.25+ },+ {+ "pad": "7",+ "text": "GND",+ "x": 0.5,+ "y": 1.45,+ "align": "right",+ "vertical": true,+ "h": 0.25+ },+ {+ "pad": "8",+ "text": "VDD",+ "x": 1.7,+ "y": 0.75,+ "align": "left",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "9",+ "text": "INT2/DEN",+ "x": 1.7,+ "y": 0.25,+ "align": "left",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "10",+ "text": "OCS_Aux",+ "x": 1.7,+ "y": -0.25,+ "align": "left",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "11",+ "text": "SDO_Aux",+ "x": 1.7,+ "y": -0.75,+ "align": "left",+ "vertical": false,+ "h": 0.25+ },+ {+ "pad": "12",+ "text": "CS",+ "x": 0.5,+ "y": -1.45,+ "align": "left",+ "vertical": true,+ "h": 0.25+ },+ {+ "pad": "13",+ "text": "SCL/SPC",+ "x": 0.0,+ "y": -1.45,+ "align": "left",+ "vertical": true,+ "h": 0.25+ },+ {+ "pad": "14",+ "text": "SDA/SDI/SDO",+ "x": -0.5,+ "y": -1.45,+ "align": "left",+ "vertical": true,+ "h": 0.25+ }+ ],+ "pads": [+ {+ "number": "1",+ "shape": "rect",+ "center_mm": [+ -1.2625,+ -0.75+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "2",+ "shape": "rect",+ "center_mm": [+ -1.2625,+ -0.25+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "3",+ "shape": "rect",+ "center_mm": [+ -1.2625,+ 0.25+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "4",+ "shape": "rect",+ "center_mm": [+ -1.2625,+ 0.75+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "5",+ "shape": "rect",+ "center_mm": [+ -0.5,+ 1.0125+ ],+ "size_mm": [+ 0.25,+ 0.675+ ],+ "rot": 0.0+ },+ {+ "number": "6",+ "shape": "rect",+ "center_mm": [+ 0.0,+ 1.0125+ ],+ "size_mm": [+ 0.25,+ 0.675+ ],+ "rot": 0.0+ },+ {+ "number": "7",+ "shape": "rect",+ "center_mm": [+ 0.5,+ 1.0125+ ],+ "size_mm": [+ 0.25,+ 0.675+ ],+ "rot": 0.0+ },+ {+ "number": "8",+ "shape": "rect",+ "center_mm": [+ 1.2625,+ 0.75+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "9",+ "shape": "rect",+ "center_mm": [+ 1.2625,+ 0.25+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "10",+ "shape": "rect",+ "center_mm": [+ 1.2625,+ -0.25+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "11",+ "shape": "rect",+ "center_mm": [+ 1.2625,+ -0.75+ ],+ "size_mm": [+ 0.675,+ 0.25+ ],+ "rot": 0.0+ },+ {+ "number": "12",+ "shape": "rect",+ "center_mm": [+ 0.5,+ -1.0125+ ],+ "size_mm": [+ 0.25,+ 0.675+ ],+ "rot": 0.0+ },+ {+ "number": "13",+ "shape": "rect",+ "center_mm": [+ 0.0,+ -1.0125+ ],+ "size_mm": [+ 0.25,+ 0.675+ ],+ "rot": 0.0+ },+ {+ "number": "14",+ "shape": "rect",+ "center_mm": [+ -0.5,+ -1.0125+ ],+ "size_mm": [+ 0.25,+ 0.675+ ],+ "rot": 0.0+ }+ ]+}
package.json+187−4@@ -1,6 +1,6 @@ { "slug": "lsm6dsotr",- "version": "0.2.0",+ "version": "0.2.1", "type": "component", "description": "STMicroelectronics Attitude Sensor/Gyroscope, LGA-14(2.5x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.", "tags": [@@ -20,10 +20,193 @@ "lsm6dsotr.kicad_mod", "lsm6dsotr.glb", "lsm6dsotr.step",+ "lsm6dsotr-etched.step", "lsm6dsotr.lbr", "docs/hero.png", "docs/lsm6dsotr-datasheet.pdf", "viewers/symbol.html",- "viewers/footprint.html"- ]-}+ "viewers/footprint.html",+ "lsm6dsotr-hero.glb",+ "lsm6dsotr-hero.overlay.json"+ ],+ "component": {+ "mpn": "LSM6DSOTR",+ "manufacturer": "STMicroelectronics",+ "package": "LGA-14(2.5x3)",+ "pin_count": 14,+ "category": "Sensor",+ "subcategory": "Attitude Sensor/Gyroscope",+ "datasheet": "https://www.st.com/resource/en/datasheet/lsm6dsotr.pdf",+ "parts": {+ "symbol": "lsm6dsotr.kicad_sym",+ "footprint": "lsm6dsotr.kicad_mod",+ "model_3d": "lsm6dsotr-hero.glb",+ "model_3d_plain": "lsm6dsotr.glb",+ "model_3d_step": "lsm6dsotr-etched.step",+ "model_3d_step_plain": "lsm6dsotr.step",+ "lbr": "lsm6dsotr.lbr"+ },+ "distributor_links": {},+ "pins": [+ {+ "number": "1",+ "name": "SDO/SA0",+ "type": "bidirectional",+ "description": "SPI 4-wire serial data output (SDO) in SPI mode; also serves as the least-significant bit of the I2C slave address (SA0) - tied high sets I2C address 1101011b, tied low sets 1101010b."+ },+ {+ "number": "2",+ "name": "SDx",+ "type": "bidirectional",+ "description": "Sensor-hub / auxiliary interface data pin. Mode 1: tie to VDDIO or GND. Mode 2: master I2C serial data (MSDA). Mode 3/4: auxiliary SPI 3/4-wire serial data input (SDI) and SPI 3-wire serial data output (SDO)."+ },+ {+ "number": "3",+ "name": "SCx",+ "type": "bidirectional",+ "description": "Sensor-hub / auxiliary interface clock pin. Mode 1: tie to VDDIO or GND. Mode 2: master I2C serial clock (MSCL). Mode 3/4: auxiliary SPI 3/4-wire serial port clock (SPC_Aux)."+ },+ {+ "number": "4",+ "name": "INT1",+ "type": "output",+ "description": "Programmable interrupt 1 output, available in both I2C and SPI modes; polarity and event mapping (data ready, FIFO threshold/full/ovr, wakeup, free-fall, tap, 6D, tilt, SMD, FSM, etc.) are register-configurable."+ },+ {+ "number": "5",+ "name": "VDDIO",+ "type": "power_in",+ "description": "Power supply for the digital I/O pins. Operating range 1.62 V to 3.6 V. A 100 nF filter capacitor to GND is recommended."+ },+ {+ "number": "6",+ "name": "GND",+ "type": "power_in",+ "description": "0 V supply / device ground reference."+ },+ {+ "number": "7",+ "name": "GND",+ "type": "power_in",+ "description": "0 V supply / device ground reference."+ },+ {+ "number": "8",+ "name": "VDD",+ "type": "power_in",+ "description": "Analog / core supply voltage. Operating range 1.71 V to 3.6 V (typ 1.8 V). A 100 nF filter capacitor to GND is recommended."+ },+ {+ "number": "9",+ "name": "INT2/DEN",+ "type": "bidirectional",+ "description": "Programmable interrupt 2 (INT2) output, doubles as Data ENable (DEN) input. In Mode 2 it can also serve as MDRDY, the I2C-master external synchronization signal."+ },+ {+ "number": "10",+ "name": "OCS_Aux",+ "type": "input",+ "description": "Auxiliary SPI interface chip-select / enable. In Modes 1 and 2 (no auxiliary SPI): leave electrically unconnected but soldered to the PCB."+ },+ {+ "number": "11",+ "name": "SDO_Aux",+ "type": "tri_state",+ "description": "Auxiliary SPI 4-wire serial data output (SDO_Aux). In auxiliary-SPI 3-wire mode, and in Modes 1/2 that do not use the auxiliary interface, tie to VDD_IO or leave electrically unconnected but soldered to the PCB."+ },+ {+ "number": "12",+ "name": "CS",+ "type": "input",+ "description": "I2C/MIPI-I3C vs SPI interface-mode select and SPI chip-select. Tie high (1) for SPI idle / I2C·I3C communication enabled; drive low (0) for SPI communication / I2C·I3C disabled."+ },+ {+ "number": "13",+ "name": "SCL/SPC",+ "type": "input",+ "description": "Main host interface serial clock: I2C/MIPI I3C serial clock (SCL) when I2C/I3C is selected, or SPI serial port clock (SPC) when SPI is selected."+ },+ {+ "number": "14",+ "name": "SDA/SDI/SDO",+ "type": "bidirectional",+ "description": "Main host interface serial data: I2C/MIPI I3C serial data (SDA) when I2C/I3C is selected, SPI serial data input (SDI) in 4-wire SPI mode, or 3-wire SPI serial data output (SDO) when 3-wire SPI is enabled via CTRL3_C (SIM)."+ }+ ],+ "provenance": {+ "extractor": "ds2sf",+ "datasheet": {+ "url": "https://www.st.com/resource/en/datasheet/lsm6dsotr.pdf",+ "pages": 172,+ "sha256": "1074e39739595e97",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 14,+ "described": 14,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lsm6dsotr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.5,+ 0.78+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "a441fc384db400c96db6affec2f9c22a5d76b0729e0f2fc46c53746be60b76ca",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lsm6dsotr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.5,+ 0.78+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "7884843582988d950d24b95223d4c165b0c49460c8cffb0f8b87f0cbd0b991cb",+ "checked": "2026-10-07",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "title": "LSM6DSOTR",+ "brief": "STMicroelectronics Attitude Sensor/Gyroscope, LGA-14(2.5x3). Pinout extracted from the datasheet, KiCad symbol/footprint/3D.",+ "metadata": {+ "specs": {+ "Manufacturer": "STMicroelectronics",+ "Package": "LGA-14(2.5x3)",+ "Category": "Sensor",+ "Pins": "14"+ }+ },+ "discovery_triggers": [+ "lsm6dsotr"+ ],+ "discovery_pitch": "LSM6DSOTR (STMicroelectronics) component page with datasheet-verified CAD.",+ "visibility": "public"+}
page.json+9−7@@ -4,7 +4,7 @@ "slug": "lsm6dsotr", "title": "LSM6DSOTR", "brief": "STMicroelectronics Attitude Sensor/Gyroscope, LGA-14(2.5x3). Pinout extracted from the datasheet, KiCad symbol/footprint/3D.",- "version": "0.2.0",+ "version": "0.2.1", "license": "CC-BY-SA-4.0", "tags": [ "component",@@ -215,16 +215,18 @@ "docs/hero.png", "docs/lsm6dsotr-datasheet.pdf", "viewers/symbol.html",- "viewers/footprint.html"+ "viewers/footprint.html",+ "lsm6dsotr-hero.glb",+ "lsm6dsotr-hero.overlay.json" ],- "visibility": {- "public": true- },+ "visibility": "public", "variants": [ { "mpn": "LSM6DSOTR", "kind": "packaging" } ],- "updated_at": "2026-09-28T18:11:08.678Z"-}+ "updated_at": "2026-09-28T18:11:08.678Z",+ "description": "STMicroelectronics Attitude Sensor/Gyroscope, LGA-14(2.5x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "org": "adom"+}