component
LSM6DSO16ISTR
Public Made by Adomby adom
STMicroelectronics Accelerometers, LGA-14(2.5x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+50@@ -0,0 +1,50 @@+# LSM6DSO16ISTR++**STMicroelectronics** · Accelerometers · LGA-14(2.5x3)++LSM6DSO16ISTR from STMicroelectronics, in a LGA-14(2.5x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SDO/SA0 | bidirectional | Mode 1: SPI 4-wire serial data output (SDO); Mode 2: I²C least significant bit of the device address (SA0), where SA0 tied to VDD selects address 1101011b and tied to GND selects 1101010b; default is input without pull-up, with pull-up enabled by SDO_PU_EN in PIN_CTRL (02h). |+| 2 | MSDA | bidirectional | Mode 1: connect to Vdd_IO or GND; Mode 2: I²C serial data line of the master interface (MSDA), default input without pull-up, with pull-up enabled by SHUB_PU_EN in MASTER_CONFIG (14h). |+| 3 | MSCL | bidirectional | Mode 1: connect to Vdd_IO or GND; Mode 2: I²C serial clock of the master interface (MSCL), default input without pull-up, with pull-up enabled by SHUB_PU_EN in MASTER_CONFIG (14h). |+| 4 | INT1 | bidirectional | Programmable interrupt 1 in both modes; default is input with pull-down, and INT1 must be set to 0 or left unconnected during power-on. |+| 5 | Vdd_IO | power_in | Power supply for the I/O pins; a 100 nF filter capacitor is recommended. |+| 6 | GND | power_in | 0 V supply. |+| 7 | GND | power_in | 0 V supply. |+| 8 | Vdd | power_in | Power supply for the device core and analog circuitry; a 100 nF filter capacitor is recommended, placed as near as possible to the pin, and the analog supply range is stated as 1.71 V to 3.6 V. |+| 9 | INT2 | bidirectional | Mode 1: programmable interrupt 2 (INT2); Mode 2: programmable interrupt 2 (INT2) multiplexed with the I²C master external synchronization signal (MDRDY); default output is forced to ground. |+| 10 | RES | unconnected | Reserved; leave electrically unconnected (pin is soldered to the PCB). |+| 11 | RES | passive | Reserved; connect to Vdd_IO or leave electrically unconnected (pin is soldered to the PCB). |+| 12 | CS | input | I²C/SPI mode selection: 1 selects SPI idle mode with I²C communication enabled, 0 selects SPI communication mode with I²C disabled; default input with pull-up. |+| 13 | SCL | input | I²C serial clock (SCL) or SPI serial port clock (SPC); default input without pull-up. |+| 14 | SDA | bidirectional | I²C serial data (SDA), SPI serial data input (SDI), or 3-wire interface serial data output (SDO); default input without pull-up. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LGA-14(2.5x3) |+| Category | Sensors |+| Pins | 14 |++## CAD (KiCad official)++- Symbol: `LSM6DSO16ISTR`+- Footprint: `Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm`+- 3D model: LGA-14(2.5x3) (KiCad packages3D, STEP)+- 3D model files: `lsm6dso16istr-etched.step` / `lsm6dso16istr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lsm6dso16istr.step` / `lsm6dso16istr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8551491705045209088) (107 pp, sha256 `30f343bb97cd697d`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lsm6dso16istr-datasheet.pdf)
page.jsonadded+236@@ -0,0 +1,236 @@+{+ "slug": "lsm6dso16istr",+ "version": "0.1.0",+ "type": "component",+ "description": "STMicroelectronics Accelerometers, LGA-14(2.5x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "sensors",+ "lsm6dso16istr",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lsm6dso16istr.kicad_sym",+ "lsm6dso16istr.kicad_mod",+ "lsm6dso16istr.glb",+ "lsm6dso16istr.step",+ "lsm6dso16istr.lbr",+ "docs/hero.png",+ "docs/lsm6dso16istr-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "lsm6dso16istr-hero.glb",+ "lsm6dso16istr-hero.overlay.json"+ ],+ "component": {+ "mpn": "LSM6DSO16ISTR",+ "manufacturer": "STMicroelectronics",+ "package": "LGA-14(2.5x3)",+ "pin_count": 14,+ "category": "Sensors",+ "subcategory": "Accelerometers",+ "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8551491705045209088",+ "parts": {+ "symbol": "lsm6dso16istr.kicad_sym",+ "footprint": "lsm6dso16istr.kicad_mod",+ "model_3d": "lsm6dso16istr-hero.glb",+ "model_3d_plain": "lsm6dso16istr.glb",+ "model_3d_step": "lsm6dso16istr-etched.step",+ "model_3d_step_plain": "lsm6dso16istr.step",+ "lbr": "lsm6dso16istr.lbr"+ },+ "distributor_links": {+ "lcsc": "C5267402",+ "digikey": "497-LSM6DSO16ISTR-ND",+ "mouser": "511-LSM6DSO16ISTR"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T03:46:00Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "497-LSM6DSO16ISTR-ND",+ "status": "found",+ "lifecycle": "Active"+ },+ "mouser": {+ "pn": "511-LSM6DSO16ISTR",+ "status": "found"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "SDO/SA0",+ "type": "bidirectional",+ "description": "Mode 1: SPI 4-wire serial data output (SDO); Mode 2: I²C least significant bit of the device address (SA0), where SA0 tied to VDD selects address 1101011b and tied to GND selects 1101010b; default is input without pull-up, with pull-up enabled by SDO_PU_EN in PIN_CTRL (02h)."+ },+ {+ "number": "2",+ "name": "MSDA",+ "type": "bidirectional",+ "description": "Mode 1: connect to Vdd_IO or GND; Mode 2: I²C serial data line of the master interface (MSDA), default input without pull-up, with pull-up enabled by SHUB_PU_EN in MASTER_CONFIG (14h)."+ },+ {+ "number": "3",+ "name": "MSCL",+ "type": "bidirectional",+ "description": "Mode 1: connect to Vdd_IO or GND; Mode 2: I²C serial clock of the master interface (MSCL), default input without pull-up, with pull-up enabled by SHUB_PU_EN in MASTER_CONFIG (14h)."+ },+ {+ "number": "4",+ "name": "INT1",+ "type": "bidirectional",+ "description": "Programmable interrupt 1 in both modes; default is input with pull-down, and INT1 must be set to 0 or left unconnected during power-on."+ },+ {+ "number": "5",+ "name": "Vdd_IO",+ "type": "power_in",+ "description": "Power supply for the I/O pins; a 100 nF filter capacitor is recommended."+ },+ {+ "number": "6",+ "name": "GND",+ "type": "power_in",+ "description": "0 V supply."+ },+ {+ "number": "7",+ "name": "GND",+ "type": "power_in",+ "description": "0 V supply."+ },+ {+ "number": "8",+ "name": "Vdd",+ "type": "power_in",+ "description": "Power supply for the device core and analog circuitry; a 100 nF filter capacitor is recommended, placed as near as possible to the pin, and the analog supply range is stated as 1.71 V to 3.6 V."+ },+ {+ "number": "9",+ "name": "INT2",+ "type": "bidirectional",+ "description": "Mode 1: programmable interrupt 2 (INT2); Mode 2: programmable interrupt 2 (INT2) multiplexed with the I²C master external synchronization signal (MDRDY); default output is forced to ground."+ },+ {+ "number": "10",+ "name": "RES",+ "type": "unconnected",+ "description": "Reserved; leave electrically unconnected (pin is soldered to the PCB)."+ },+ {+ "number": "11",+ "name": "RES",+ "type": "passive",+ "description": "Reserved; connect to Vdd_IO or leave electrically unconnected (pin is soldered to the PCB)."+ },+ {+ "number": "12",+ "name": "CS",+ "type": "input",+ "description": "I²C/SPI mode selection: 1 selects SPI idle mode with I²C communication enabled, 0 selects SPI communication mode with I²C disabled; default input with pull-up."+ },+ {+ "number": "13",+ "name": "SCL",+ "type": "input",+ "description": "I²C serial clock (SCL) or SPI serial port clock (SPC); default input without pull-up."+ },+ {+ "number": "14",+ "name": "SDA",+ "type": "bidirectional",+ "description": "I²C serial data (SDA), SPI serial data input (SDI), or 3-wire interface serial data output (SDO); default input without pull-up."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The datasheet names the package LGA-14L (2.5 x 3.0 x 0.86 mm, with 0.83 mm typical height in the fea; Pins 1, 2, 3, 9 and 14 have mode-dependent functions (Mode 1 vs Mode 2 connection). The type shown i; The datasheet does not give a numeric voltage range for Vdd_IO. The features list only 'independent "+ ],+ "pages_sent": 31,+ "cost_usd": 0.1187,+ "at": "2026-10-08T03:45:46"+ },+ "datasheet": {+ "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8551491705045209088",+ "pages": 107,+ "sha256": "30f343bb97cd697d",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 14,+ "described": 14,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lsm6dso16istr.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.5,+ 0.78+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "a441fc384db400c96db6affec2f9c22a5d76b0729e0f2fc46c53746be60b76ca",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lsm6dso16istr-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.5,+ 0.78+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "f84839adedd2e12bfc6b41a6550588f78172231a54aacb7c6a6768b4b8bc34fc",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}