← Commit history
page.json+11−8@@ -32,37 +32,37 @@ "number": "1", "name": "SD", "type": "input",- "description": "Shutdown pin, active high. Drive above VSD_H (min 1.2 V at VDD=5 V) to enable the amplifier; drive below VSD_L (max 0.6 V) or to GND to place the device in shutdown (ILEAK \u2248 0.1 \u00b5A)."+ "description": "Shutdown pin, active high. Drive above VSD_H (min 1.2 V at VDD=5 V) to enable the amplifier; drive below VSD_L (max 0.6 V) or to GND to place the device in shutdown (ILEAK ≈ 0.1 µA)." }, { "number": "2", "name": "BYP", "type": "passive",- "description": "Analog reference bypass pin, biased internally to approximately VDD/2. Connect a 1 \u00b5F ceramic capacitor from this pin to GND; the capacitor sets start-up time and improves PSRR/THD+N."+ "description": "Analog reference bypass pin, biased internally to approximately VDD/2. Connect a 1 µF ceramic capacitor from this pin to GND; the capacitor sets start-up time and improves PSRR/THD+N." }, { "number": "3", "name": "INP", "type": "input",- "description": "Positive audio input of the amplifier. AC-couple through Ci (typ 0.22 \u00b5F) and series input resistor Ri (typ 20 k\u03a9) forming a high-pass filter with the internal input resistance; used differentially with INN or single-ended (tie the unused side to a Ci to GND)."+ "description": "Positive audio input of the amplifier. AC-couple through Ci (typ 0.22 µF) and series input resistor Ri (typ 20 kΩ) forming a high-pass filter with the internal input resistance; used differentially with INN or single-ended (tie the unused side to a Ci to GND)." }, { "number": "4", "name": "INN", "type": "input",- "description": "Negative audio input of the amplifier. AC-couple through Ci (typ 0.22 \u00b5F) and Ri (typ 20 k\u03a9). For single-ended input, still AC-couple this pin to signal ground through Ci/Ri."+ "description": "Negative audio input of the amplifier. AC-couple through Ci (typ 0.22 µF) and Ri (typ 20 kΩ). For single-ended input, still AC-couple this pin to signal ground through Ci/Ri." }, { "number": "5", "name": "VOP", "type": "output",- "description": "Positive (non-inverting) Class-D BTL output. Connect directly to one speaker terminal; no LC output filter is required for speaker leads \u2264 ~100 mm. Optionally add a ferrite bead + 1 nF to GND for EMI reduction."+ "description": "Positive (non-inverting) Class-D BTL output. Connect directly to one speaker terminal; no LC output filter is required for speaker leads ≤ ~100 mm. Optionally add a ferrite bead + 1 nF to GND for EMI reduction." }, { "number": "6", "name": "VDD", "type": "power_in",- "description": "Positive supply input, 2.5 V to 5.5 V operating (6.0 V absolute max). Decouple with 1 \u00b5F ceramic close to the pin and a bulk 22 \u00b5F capacitor nearby."+ "description": "Positive supply input, 2.5 V to 5.5 V operating (6.0 V absolute max). Decouple with 1 µF ceramic close to the pin and a bulk 22 µF capacitor nearby." }, { "number": "7",@@ -74,7 +74,7 @@ "number": "8", "name": "VON", "type": "output",- "description": "Negative (inverting) Class-D BTL output, 180\u00b0 out of phase with VOP. Connect directly to the other speaker terminal; drives 4 \u03a9 / 8 \u03a9 loads with up to 3 W (10% THD, 5 V, 4 \u03a9)."+ "description": "Negative (inverting) Class-D BTL output, 180° out of phase with VOP. Connect directly to the other speaker terminal; drives 4 Ω / 8 Ω loads with up to 3 W (10% THD, 5 V, 4 Ω)." } ], "provenance": {@@ -144,5 +144,8 @@ "docs/lpa2104asof-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ]+ ],+ "visibility": {+ "public": true+ } }