← Commit history

lp7801tspf: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·3e76bacea9 · ·parent 4aff9c6
1 file changed +80−1
page.json+80−1
@@ -33,5 +33,84 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "LP7801TSPF",+    "manufacturer": "LOWPOWER",+    "package": "ESOP-8",+    "pin_count": 9,+    "category": "Battery Management",+    "parts": {+      "symbol": "lp7801tspf.kicad_sym",+      "footprint": "lp7801tspf.kicad_mod",+      "model_3d": "lp7801tspf-etched.glb",+      "model_3d_plain": "lp7801tspf.glb",+      "model_3d_step": "lp7801tspf-etched.step",+      "model_3d_step_plain": "lp7801tspf.step",+      "lbr": "lp7801tspf.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "ISET",+        "type": "input",+        "description": "Charging current programming pin. Connect a resistor from ISET to GND to set the constant-current charging current per ICC = 1750 × VISET/RISET where VISET = 1 V (e.g. RISET = 17.5 kΩ → 100 mA; RISET = 3.4 kΩ → 515 mA)."+      },+      {+        "number": "2",+        "name": "VIN",+        "type": "power_in",+        "description": "Linear charger input supply. Recommended operating range 4.5 V to 5.8 V; tolerates up to 36 V absolute maximum. Input over-voltage protection threshold is 6.3 V (rising) with 400 mV hysteresis; UVLO is 3.3 V. Decouple with a 1 µF capacitor to GND."+      },+      {+        "number": "3",+        "name": "BAT",+        "type": "bidirectional",+        "description": "Linear charger output to the Li-ion battery and input to the boost converter. Regulates to VFLOAT = 4.20 V (LP7801TSPF) or 4.35 V (LP7801TSPF-435). Charging current up to 1 A; auto-recharge threshold VFLOAT − 150 mV. Decouple with 10 µF capacitor to GND."+      },+      {+        "number": "4",+        "name": "SW",+        "type": "output",+        "description": "Switching node of the synchronous boost converter. Connect a 2.2 µH inductor from BAT to SW. Absolute maximum −0.3 V to +9 V. Switch current limit typ. 1 A; high-side/low-side MOS RON ≈ 160 mΩ/220 mΩ."+      },+      {+        "number": "5",+        "name": "VOUT",+        "type": "power_out",+        "description": "Regulated boost converter output, fixed 5.1 V (Typ.), up to 500 mA. Decouple with 2 × 10 µF ceramic capacitors to GND. Discharged through an internal 2 kΩ resistor to 0 V when EN is low."+      },+      {+        "number": "6",+        "name": "EN",+        "type": "input",+        "description": "Active-high enable input for the boost converter. VIH ≥ 1.4 V enables the converter, VIL ≤ 0.4 V disables it and engages the 2 kΩ output discharge. Leakage 0.01 µA at VEN = 5 V."+      },+      {+        "number": "7",+        "name": "CHRG",+        "type": "output",+        "description": "Open-drain charge status indicator, capable of driving an LED. Strong pull-down (~10 mA sink, VOL ≤ 0.5 V at 5 mA) during a charge cycle; high impedance when the cycle terminates or when VIN is below 4.5 V / above the OVP threshold. Leakage 5 µA at VCHRG = 5 V, VBAT = 4.3 V."+      },+      {+        "number": "8",+        "name": "TS",+        "type": "input",+        "description": "Battery temperature sense input. Connect via a resistor divider (R1, R2) with an external NTC to VIN. Charging is allowed only when the TS voltage is between VTS_L (30 %·VIN, rising) and VTS_H (60 %·VIN, falling), with 30 mV hysteresis. Tie via equal R1/R2 (TS ≈ 50 %·VIN) if thermal protection is unused."+      },+      {+        "number": "9",+        "name": "GND",+        "type": "power_in",+        "description": "Ground / exposed thermal pad on the bottom of the ESOP-8 package. Must be soldered to the PCB ground plane for thermal dissipation (θJA ≈ 50 °C/W on 2S2P JEDEC PCB) and electrical return."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}