← Commit history

lp2998max: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·7774bbe78f · ·parent e819f3b
1 file changed +75−1
page.json+75−1
@@ -33,5 +33,79 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "LP2998MAX",+    "manufacturer": "Texas Instruments",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "Battery Management",+    "datasheet": "https://www.ti.com/lit/ds/symlink/lp2998max.pdf",+    "parts": {+      "symbol": "lp2998max.kicad_sym",+      "footprint": "lp2998max.kicad_mod",+      "model_3d": "lp2998max-etched.glb",+      "model_3d_plain": "lp2998max.glb",+      "model_3d_step": "lp2998max-etched.step",+      "model_3d_step_plain": "lp2998max.step",+      "lbr": "lp2998max.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground return. Also connect the exposed pad (DDA package) to this net; SOIC-8 (MAX) has no exposed pad."+      },+      {+        "number": "2",+        "name": "SD",+        "type": "input",+        "description": "Active-low shutdown. When pulled low the VTT output tri-states (Suspend-To-RAM); VREF remains active. Has an internal pull-up current so it can be left open or tied to AVIN to enable. Input range 0 to AVIN."+      },+      {+        "number": "3",+        "name": "VSENSE",+        "type": "input",+        "description": "Remote-sense feedback pin for VTT regulation. Connect to VTT at the point of load (middle of the termination bus) for best distributed load regulation; tie directly to VTT at the pin if remote sense is not used. A small 0.1 µF ceramic near the pin helps reject noise pickup."+      },+      {+        "number": "4",+        "name": "VREF",+        "type": "output",+        "description": "Buffered VDDQ/2 reference output for chipset/DIMM Vref inputs. Nominally 1.258 V (DDR-I, VDDQ=2.5 V), 0.910 V (DDR-II, 1.8 V) or 0.758 V (DDR-III, 1.5 V). Output impedance ~2.5 kΩ over ±30 µA; remains active during shutdown / thermal shutdown. Bypass with 0.01-0.1 µF ceramic near the pin."+      },+      {+        "number": "5",+        "name": "VDDQ",+        "type": "input",+        "description": "Sense input for generating the internal VDDQ/2 reference via two internal 50 kΩ resistors (100 kΩ to GND total, always drawing current even in shutdown). Best used as a remote sense tied to the DDR VDDQ rail at the DIMM. Absolute max 6 V, and must be ≤ 2×(AVIN−1) V."+      },+      {+        "number": "6",+        "name": "AVIN",+        "type": "power_in",+        "description": "Analog supply for the internal control circuitry. Recommended operating range 2.2 V to 5.5 V (absolute max 6 V). AVIN must be ≥ PVIN."+      },+      {+        "number": "7",+        "name": "PVIN",+        "type": "power_in",+        "description": "Power input to the VTT output stage. Range 0 V to AVIN; recommended ≤ 3.3 V to keep internal dissipation within the thermal limit. Higher PVIN increases maximum continuous output current by lowering RDSON headroom above VTT."+      },+      {+        "number": "8",+        "name": "VTT",+        "type": "power_out",+        "description": "Regulated DDR termination output at VDDQ/2. Sources and sinks up to ±1.5 A continuous with peak transients to ±3 A; tri-stated during SD-asserted shutdown and thermal shutdown. Requires a bulk output capacitor sized for expected transient step; VTT must not be pulled above AVIN while in shutdown."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}