← Commit history

Initial commit: component/lp2951cmx-3-3

Ray ·f3be931140 ·
2 files changed +86
README.mdadded+52
@@ -0,0 +1,52 @@+# LP2951CMX-3.3++**Texas Instruments LP2951CMX 3 3 NOPB** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOIC-8++LP2951CMX-3.3 from Texas Instruments LP2951CMX 3 3 NOPB, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OUT | power_out | Regulated output voltage (3.3 V nominal, ±0.5% or ±1% initial tolerance). Sources up to 100 mA. Requires a minimum 2.2 µF output capacitor with ESR in the range 10 mΩ-6 Ω for stability. |+| 2 | SENSE | input | Output voltage sense input for the internal error amplifier. In fixed-output mode connect directly to the OUT pin (pin 1); in adjustable mode this pin ties to the top of the external feedback network to Kelvin-sense the load. |+| 3 | SHUTDOWN | input | Active-high logic-controlled shutdown input. Drive high (>2 V) to disable the regulator (output off, quiescent current drops); drive low (<0.7 V) or leave tied to GND for normal operation. Withstands the full input supply voltage range (up to 30 V). |+| 4 | GND | power_in | Device ground / negative supply reference. All voltages are referenced to this pin. On the WSON (NGT) package the die-attach pad (DAP) must be connected to GND at pin 4. |+| 5 | ERROR | output | Open-collector error-flag output. Pulls low when the regulated output falls ~5% below its nominal value (e.g. due to input dropout or overload); high-impedance otherwise. Requires an external pull-up resistor to a logic supply. Commonly used to generate a power-on-reset signal. |+| 6 | VTAP | output | Tap point of the internal output-programming resistor divider (nominally 1.235 V, the internal band-gap reference). In the fixed 3.3-V configuration this pin is tied to the FEEDBACK pin (pin 7) to select the on-chip 3.3-V setpoint. May also be used as a low-current reference output. |+| 7 | FEEDBACK | input | Inverting input of the internal error amplifier (regulation setpoint = 1.235 V typ). For the fixed 3.3-V output, tie FEEDBACK to VTAP (pin 6). For adjustable operation, drive with the tap of an external R1/R2 divider from OUT to GND; Vout = 1.235 × (1 + R1/R2). Rated -1.5 V to +30 V. |+| 8 | IN | power_in | Unregulated input supply. Operating range 2.3 V to 30 V; must exceed VOUT + Vdropout (≈380 mV at 100 mA, 40 mV at light load). Requires a minimum 1 µF input capacitor near the pin. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments LP2951CMX 3 3 NOPB |+| Package | SOIC-8 |+| Category | PMIC |+| Pins | 8 |++## Ordering variants++- `LP2951CMX-3.3`+- `LP2951CMX-3.3CM-3.3`+- `LP2951CMX-3.3CDGKR-3.3`+- `LP2951CMX-3.3CDGK-3.3`+- `LP2951CMX-3.3NGT`+- `LP2951CMX-3.3N`++## CAD (KiCad official)++- Symbol: `LP2951CMX-3.3`+- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`+- 3D model: SOIC-8 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments LP2951CMX 3 3 NOPB datasheet](https://www.ti.com/lit/ds/symlink/lp2951cmx-3.3.pdf) (None pp, sha256 `a598f6d0f6acb68d`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lp2951cmx-3-3-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "lp2951cmx-3-3",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments LP2951CMX 3 3 NOPB Voltage Regulators - Linear, Low Drop Out (LDO) Regulators, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "lp2951cmx-3.3"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lp2951cmx-3-3.kicad_sym",+    "lp2951cmx-3-3.kicad_mod",+    "lp2951cmx-3-3.glb",+    "lp2951cmx-3-3.step",+    "lp2951cmx-3-3.lbr",+    "docs/hero.png",+    "docs/lp2951cmx-3-3-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file