← Commit history

lp2951cmx-3-3: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·d26265345d · ·parent c028d61
1 file changed +75−1
page.json+75−1
@@ -33,5 +33,79 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "LP2951CMX-3.3",+    "manufacturer": "Texas Instruments LP2951CMX 3 3 NOPB",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "Voltage Regulators - Linear, Low Drop Out (LDO) Regulators",+    "datasheet": "https://www.ti.com/lit/ds/symlink/lp2951cmx-3.3.pdf",+    "parts": {+      "symbol": "lp2951cmx-3-3.kicad_sym",+      "footprint": "lp2951cmx-3-3.kicad_mod",+      "model_3d": "lp2951cmx-3-3-etched.glb",+      "model_3d_plain": "lp2951cmx-3-3.glb",+      "model_3d_step": "lp2951cmx-3-3-etched.step",+      "model_3d_step_plain": "lp2951cmx-3-3.step",+      "lbr": "lp2951cmx-3-3.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "OUT",+        "type": "power_out",+        "description": "Regulated output voltage (3.3 V nominal, ±0.5% or ±1% initial tolerance). Sources up to 100 mA. Requires a minimum 2.2 µF output capacitor with ESR in the range 10 mΩ-6 Ω for stability."+      },+      {+        "number": "2",+        "name": "SENSE",+        "type": "input",+        "description": "Output voltage sense input for the internal error amplifier. In fixed-output mode connect directly to the OUT pin (pin 1); in adjustable mode this pin ties to the top of the external feedback network to Kelvin-sense the load."+      },+      {+        "number": "3",+        "name": "SHUTDOWN",+        "type": "input",+        "description": "Active-high logic-controlled shutdown input. Drive high (>2 V) to disable the regulator (output off, quiescent current drops); drive low (<0.7 V) or leave tied to GND for normal operation. Withstands the full input supply voltage range (up to 30 V)."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Device ground / negative supply reference. All voltages are referenced to this pin. On the WSON (NGT) package the die-attach pad (DAP) must be connected to GND at pin 4."+      },+      {+        "number": "5",+        "name": "ERROR",+        "type": "output",+        "description": "Open-collector error-flag output. Pulls low when the regulated output falls ~5% below its nominal value (e.g. due to input dropout or overload); high-impedance otherwise. Requires an external pull-up resistor to a logic supply. Commonly used to generate a power-on-reset signal."+      },+      {+        "number": "6",+        "name": "VTAP",+        "type": "output",+        "description": "Tap point of the internal output-programming resistor divider (nominally 1.235 V, the internal band-gap reference). In the fixed 3.3-V configuration this pin is tied to the FEEDBACK pin (pin 7) to select the on-chip 3.3-V setpoint. May also be used as a low-current reference output."+      },+      {+        "number": "7",+        "name": "FEEDBACK",+        "type": "input",+        "description": "Inverting input of the internal error amplifier (regulation setpoint = 1.235 V typ). For the fixed 3.3-V output, tie FEEDBACK to VTAP (pin 6). For adjustable operation, drive with the tap of an external R1/R2 divider from OUT to GND; Vout = 1.235 × (1 + R1/R2). Rated -1.5 V to +30 V."+      },+      {+        "number": "8",+        "name": "IN",+        "type": "power_in",+        "description": "Unregulated input supply. Operating range 2.3 V to 30 V; must exceed VOUT + Vdropout (≈380 mV at 100 mA, 40 mV at light load). Requires a minimum 1 µF input capacitor near the pin."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}