← Commit history

Initial commit: component/lm5574mtx

Ray ·e181e420d0 ·
2 files changed +91
README.mdadded+57
@@ -0,0 +1,57 @@+# LM5574MTX++**Texas Instruments** · DC-DC Converters · TSSOP-16++LM5574MTX from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VCC | power_out | Output of the internal bias regulator. Vcc tracks Vin up to 9V; above 9V it is regulated to ~7V. Requires a 0.1µF-1µF ceramic decoupling capacitor. An external 7.5V-14V supply may be applied here to reduce internal power dissipation. |+| 2 | SD | input | Shutdown / UVLO input. VSD < 0.7V = low-power shutdown; 0.7V-1.225V = standby; > 1.225V = operational. A resistor divider from VIN sets a line-UVLO threshold; if left open a 5µA internal pull-up enables the regulator. |+| 3 | VIN | power_in | Input supply voltage. Nominal operating range 6V to 75V (absolute maximum 76V). |+| 4 | SYNC | bidirectional | Oscillator synchronization input/output. Can be driven by an external clock through an external pull-down device, or tied between multiple LM5574 devices to self-synchronize. Source impedance ~11kΩ, sink impedance ~110Ω, falling threshold 1.3V, min pulse 15ns. |+| 5 | COMP | output | Output of the internal transconductance error amplifier. Connect the loop-compensation network between this pin and FB. Sink/source capability ~3mA, unity-gain bandwidth ~3MHz. |+| 6 | FB | input | Feedback input to the internal error amplifier (inverting input). Regulation reference is 1.225V ±1.5%; bias current ~17nA. |+| 7 | RT | input | Oscillator frequency-set input. A single resistor from RT to AGND programs the switching frequency between 50kHz and 500kHz (e.g. RT = 32.4kΩ → ~200kHz; RT = 11kΩ → ~485kHz). |+| 8 | RAMP | input | Ramp-control signal for the emulated current-mode PWM. An external capacitor (50pF-2000pF) from RAMP to AGND sets the emulated ramp slope. |+| 9 | AGND | power_in | Analog ground. Internal reference for the regulator control functions; return for RT and RAMP timing components. |+| 10 | SS | input | Soft-start. An external capacitor and an internal 10µA current source set the rise time of the error-amp reference. Held low during standby, VCC UVLO, and thermal shutdown. |+| 11 | OUT | input | Output-voltage sense connection. Connect directly to the regulated output voltage rail; used by the diode current-sense/emulated-ramp circuitry. |+| 12 | PGND | power_in | Power ground. Low-side reference for the pre-charge (PRE) switch and for the internal IS current-sense resistor. |+| 13 | IS | input | Current-sense input for the external re-circulating (Schottky) diode. An internal 250mΩ sense resistor and sample/hold measure diode current near the end of the off-time, providing the DC level of the emulated current ramp. |+| 14 | SW | output | Switching node - source of the internal 75V/750mΩ N-channel buck MOSFET. Connect to the external Schottky recirculation diode and the buck inductor. Steady-state minimum rating -1.5V. |+| 15 | PRE | output | Pre-charge assist for the bootstrap capacitor. Open-drain output (Rds(on) ~70Ω) that turns on for ~250ns each cycle just before the buck-switch on-time; usually tied to SW to keep BST charged under very light load or when the output is pre-charged before enable. |+| 16 | BST | power_in | Bootstrap-capacitor input for the high-side gate drive. Connect a ~0.022µF ceramic capacitor between BST and SW; the cap is recharged from VCC through an internal diode during the buck-switch off-time. BOOST UVLO ~4V. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-16 |+| Category | PMIC |+| Pins | 16 |++## Ordering variants++- `LM5574MTX`+- `LM5574MTX/NOPB`+- `LM5574MTXMT/NOPB`++## CAD (KiCad official)++- Symbol: `LM5574MTX`+- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`+- 3D model: TSSOP-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm5574mtx.pdf) (None pp, sha256 `63b06033630731ba`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm5574mtx-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "lm5574mtx",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, TSSOP-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "lm5574mtx"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm5574mtx.kicad_sym",+    "lm5574mtx.kicad_mod",+    "lm5574mtx.glb",+    "lm5574mtx.step",+    "lm5574mtx.lbr",+    "docs/hero.png",+    "docs/lm5574mtx-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file