← Commit history

Initial commit: component/lm5117psqe

Ray ·ec12831297 ·
2 files changed +304
README.mdadded+61
@@ -0,0 +1,61 @@+# LM5117PSQE++**Texas Instruments** · DC-DC Controllers · WQFN-24-EP(4x4)++LM5117PSQE from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | DEMB | input | Optional logic input that enables diode emulation mode when held low; internal 50-kΩ pull-down enables diode emulation if pin is left floating. |+| 2 | RES | output | Restart timer pin configured by external capacitor; 10-μA internal current source charges to 1.25-V threshold after 256 consecutive cycles of current limiting. |+| 3 | SS | input | Soft-start pin charged by 10-μA internal current source; determines ramp rate of output voltage and is held low when VCC < 5V or UVLO < 1.25V. |+| 4 | RT | input | Oscillator programming pin; single external resistor sets switching frequency from 50kHz to 750kHz and can be synchronized to external clock. |+| 5 | AGND | power_in | Analog ground return for internal 0.8-V precision reference and all analog circuits. |+| 6 | NC | unconnected | No electrical connection. |+| 7 | VCCDIS | input | VCC regulator disable input; internal regulator is disabled when voltage exceeds 1.25V threshold with 500-kΩ internal pull-down resistor. |+| 8 | FB | input | Error amplifier feedback input with 0.8-V regulation threshold; external resistor divider from output sets regulated output voltage. |+| 9 | COMP | output | Error amplifier output node; loop compensation network (RCOMP, CCOMP, CHF) is connected between COMP and FB pins. |+| 10 | CM | output | Current monitor output providing average of sensed inductor current; monitor directly between CM and AGND with bandwidth approximately one-tenth of switching frequency. |+| 11 | RAMP | input | PWM ramp signal pin; external RC network (RRAMP, CRAMP) between SW, RAMP, and AGND generates emulated inductor current ramp with slope proportional to input voltage. |+| 12 | CS | input | Current sense amplifier input with 10V/V gain and 120-mV sense voltage threshold; connect to high-side of external current sense resistor. |+| 13 | CSG | power_in | Kelvin ground connection for current sense resistor; connect directly to low-side of external current sense resistor for accurate current measurement. |+| 14 | PGND | power_in | Power ground return for low-side NMOS gate driver; connect directly to current sense resistor ground and system return. |+| 15 | LO | output | Low-side NMOS gate drive output with 3.3-A sink current and 2.5-A source current; adaptive dead-time logic prevents simultaneous conduction with HO. |+| 16 | VCC | power_out | Bias supply output regulated to 7.6V by internal regulator or supplied externally when VCCDIS exceeds 1.25V threshold. |+| 17 | NC | unconnected | No electrical connection. |+| 18 | SW | output | Switching node of the buck regulator; common connection point for bootstrap capacitor, high-side NMOS source terminal, and low-side NMOS drain terminal. |+| 19 | HO | output | High-side NMOS gate drive output with 3.3-A sink current and 2.2-A source current; maximum low-state voltage drop 100mV. |+| 20 | HB | power_in | Bootstrap supply pin for high-side gate driver; connect to bootstrap diode cathode and bootstrap capacitor, typically maintains 7.6V above SW node. |+| 21 | NC | unconnected | No electrical connection. |+| 22 | VIN | power_in | Supply voltage input for internal VCC regulator; minimum VIN of 5.5V required for VCC regulation, maximum 65V absolute maximum rating. |+| 23 | NC | unconnected | No electrical connection. |+| 24 | UVLO | input | Undervoltage lockout programming pin with external resistor divider setting threshold; regulator shutdown below 0.4V, standby 0.4V-1.25V, normal operation above 1.25V. |+| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-24-EP(4x4) |+| Category | Power Supply Chip |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `LM5117PSQE`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm`+- 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5117) (49 pp, sha256 `9e27f24e84faebf5`, retrieved 2026-09-17, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm5117psqe-datasheet.pdf)
page.jsonadded+243
@@ -0,0 +1,243 @@+{+  "slug": "lm5117psqe",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Controllers, WQFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "lm5117psqe",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm5117psqe.kicad_sym",+    "lm5117psqe.kicad_mod",+    "lm5117psqe.glb",+    "lm5117psqe.step",+    "lm5117psqe.lbr",+    "docs/hero.png",+    "docs/lm5117psqe-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM5117PSQE",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Supply Chip",+    "subcategory": "DC-DC Controllers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm5117",+    "parts": {+      "symbol": "lm5117psqe.kicad_sym",+      "footprint": "lm5117psqe.kicad_mod",+      "model_3d": "lm5117psqe.glb",+      "model_3d_step": "lm5117psqe.step",+      "lbr": "lm5117psqe.lbr"+    },+    "distributor_links": {+      "lcsc": "C2658242"+    },+    "pins": [+      {+        "number": "1",+        "name": "DEMB",+        "type": "input",+        "description": "Optional logic input that enables diode emulation mode when held low; internal 50-kΩ pull-down enables diode emulation if pin is left floating."+      },+      {+        "number": "2",+        "name": "RES",+        "type": "output",+        "description": "Restart timer pin configured by external capacitor; 10-μA internal current source charges to 1.25-V threshold after 256 consecutive cycles of current limiting."+      },+      {+        "number": "3",+        "name": "SS",+        "type": "input",+        "description": "Soft-start pin charged by 10-μA internal current source; determines ramp rate of output voltage and is held low when VCC < 5V or UVLO < 1.25V."+      },+      {+        "number": "4",+        "name": "RT",+        "type": "input",+        "description": "Oscillator programming pin; single external resistor sets switching frequency from 50kHz to 750kHz and can be synchronized to external clock."+      },+      {+        "number": "5",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground return for internal 0.8-V precision reference and all analog circuits."+      },+      {+        "number": "6",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical connection."+      },+      {+        "number": "7",+        "name": "VCCDIS",+        "type": "input",+        "description": "VCC regulator disable input; internal regulator is disabled when voltage exceeds 1.25V threshold with 500-kΩ internal pull-down resistor."+      },+      {+        "number": "8",+        "name": "FB",+        "type": "input",+        "description": "Error amplifier feedback input with 0.8-V regulation threshold; external resistor divider from output sets regulated output voltage."+      },+      {+        "number": "9",+        "name": "COMP",+        "type": "output",+        "description": "Error amplifier output node; loop compensation network (RCOMP, CCOMP, CHF) is connected between COMP and FB pins."+      },+      {+        "number": "10",+        "name": "CM",+        "type": "output",+        "description": "Current monitor output providing average of sensed inductor current; monitor directly between CM and AGND with bandwidth approximately one-tenth of switching frequency."+      },+      {+        "number": "11",+        "name": "RAMP",+        "type": "input",+        "description": "PWM ramp signal pin; external RC network (RRAMP, CRAMP) between SW, RAMP, and AGND generates emulated inductor current ramp with slope proportional to input voltage."+      },+      {+        "number": "12",+        "name": "CS",+        "type": "input",+        "description": "Current sense amplifier input with 10V/V gain and 120-mV sense voltage threshold; connect to high-side of external current sense resistor."+      },+      {+        "number": "13",+        "name": "CSG",+        "type": "power_in",+        "description": "Kelvin ground connection for current sense resistor; connect directly to low-side of external current sense resistor for accurate current measurement."+      },+      {+        "number": "14",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground return for low-side NMOS gate driver; connect directly to current sense resistor ground and system return."+      },+      {+        "number": "15",+        "name": "LO",+        "type": "output",+        "description": "Low-side NMOS gate drive output with 3.3-A sink current and 2.5-A source current; adaptive dead-time logic prevents simultaneous conduction with HO."+      },+      {+        "number": "16",+        "name": "VCC",+        "type": "power_out",+        "description": "Bias supply output regulated to 7.6V by internal regulator or supplied externally when VCCDIS exceeds 1.25V threshold."+      },+      {+        "number": "17",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical connection."+      },+      {+        "number": "18",+        "name": "SW",+        "type": "output",+        "description": "Switching node of the buck regulator; common connection point for bootstrap capacitor, high-side NMOS source terminal, and low-side NMOS drain terminal."+      },+      {+        "number": "19",+        "name": "HO",+        "type": "output",+        "description": "High-side NMOS gate drive output with 3.3-A sink current and 2.2-A source current; maximum low-state voltage drop 100mV."+      },+      {+        "number": "20",+        "name": "HB",+        "type": "power_in",+        "description": "Bootstrap supply pin for high-side gate driver; connect to bootstrap diode cathode and bootstrap capacitor, typically maintains 7.6V above SW node."+      },+      {+        "number": "21",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical connection."+      },+      {+        "number": "22",+        "name": "VIN",+        "type": "power_in",+        "description": "Supply voltage input for internal VCC regulator; minimum VIN of 5.5V required for VCC regulation, maximum 65V absolute maximum rating."+      },+      {+        "number": "23",+        "name": "NC",+        "type": "unconnected",+        "description": "No electrical connection."+      },+      {+        "number": "24",+        "name": "UVLO",+        "type": "input",+        "description": "Undervoltage lockout programming pin with external resistor divider setting threshold; regulator shutdown below 0.4V, standby 0.4V-1.25V, normal operation above 1.25V."+      },+      {+        "number": "25",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 25 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 49,+        "cost_usd": 0.6191,+        "at": "2026-09-17T18:53:42"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm5117",+        "pages": 49,+        "sha256": "9e27f24e84faebf5",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file