← Commit history

Initial commit: component/lm5088mhx-2

Ray ·1429aff1eb ·
2 files changed +251
README.mdadded+54
@@ -0,0 +1,54 @@+# LM5088MHX-2++**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP++LM5088MHX-2 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN | power_in | Input supply voltage for the IC; operating range is 4.5 V to 75 V absolute maximum 76 V. |+| 2 | EN | input | Enable input with tri-level control: below 0.4 V shutdown, 0.4 V to 1.2 V standby mode, above 1.2 V operational, with 5-µA internal pull-up current. |+| 3 | SS | input | Soft start input; internal 11-µA current source charges external capacitor, with 1.2 V reference and 120 mV clamp above FB voltage. |+| 4 | RAMP | output | Ramp generator output; external 100 pF to 2000 pF capacitor connected to GND sets emulated current ramp slope for peak current mode control. |+| 5 | RT/SYNC | input | Oscillator frequency set and synchronization input; internal resistor to GND programs switching frequency 50 kHz to 1 MHz, external sync pulse width less than 150 ns. |+| 6 | GND | power_in | Ground return; signal and power ground reference for the controller. |+| 7 | COMP | output | Error amplifier output; internal 60 dB gain amplifier with 3 MHz unity-gain bandwidth, loop compensation network connected between COMP and FB pins. |+| 8 | FB | input | Feedback signal input to inverting input of error amplifier with 1.205 V regulation threshold and ±18 nA maximum input bias current. |+| 9 | OUT | input | Output voltage sensing input; connect directly to regulated output voltage to provide VIN-VOUT feedback for ramp generator compensation. |+| 10 | RES | output | Restart timer output for hiccup mode (LM5088-2 only); external capacitor sets restart delay with 50-µA charge and 25-µA discharge current sources, 1.2 V upper and 0.2 V lower thresholds. |+| 11 | CSG | power_in | Current sense ground; low-side reference terminal for external current sense resistor connected between CS and CSG pins. |+| 12 | CS | input | Current sense input measuring re-circulating diode current with internal sample-and-hold circuit and 120 mV cycle-by-cycle current limit threshold. |+| 13 | SW | output | Switching node output; connect directly to source terminal of external MOSFET switch and free-wheeling diode anode. |+| 14 | HG | output | High-side gate driver output; 1.5 A peak source and 2 A peak sink current with 12 ns rise and 6 ns fall time driving external MOSFET gate. |+| 15 | BOOT | passive | Bootstrap capacitor connection; external 0.022 µF minimum ceramic capacitor required between BOOT and SW pins, charged from VCC via internal diode. |+| 16 | VCC | power_out | Bias regulator output; 7.8 V typical regulation from VIN with 30 mA internal current limit, requires 0.1 µF to 10 µF ceramic decoupling capacitor. |+| 17 | EP | passive | Exposed thermal pad; electrically isolated must be soldered to ground plane to reduce thermal resistance per thermal analysis recommendations. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Power Management (PMIC) |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `LM5088MHX-2`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `lm5088mhx-2-etched.step` / `lm5088mhx-2-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm5088mhx-2.step` / `lm5088mhx-2.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm5088) (45 pp, sha256 `7f168fca38f1dc8e`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm5088mhx-2-datasheet.pdf)
page.jsonadded+197
@@ -0,0 +1,197 @@+{+  "slug": "lm5088mhx-2",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "lm5088mhx-2",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm5088mhx-2.kicad_sym",+    "lm5088mhx-2.kicad_mod",+    "lm5088mhx-2.glb",+    "lm5088mhx-2.step",+    "lm5088mhx-2.lbr",+    "docs/hero.png",+    "docs/lm5088mhx-2-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM5088MHX-2",+    "manufacturer": "Texas Instruments",+    "package": "HTSSOP-16-EP",+    "pin_count": 17,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm5088",+    "parts": {+      "symbol": "lm5088mhx-2.kicad_sym",+      "footprint": "lm5088mhx-2.kicad_mod",+      "model_3d": "lm5088mhx-2-etched.glb",+      "model_3d_plain": "lm5088mhx-2.glb",+      "model_3d_step": "lm5088mhx-2-etched.step",+      "model_3d_step_plain": "lm5088mhx-2.step",+      "lbr": "lm5088mhx-2.lbr"+    },+    "distributor_links": {+      "lcsc": "C115727"+    },+    "pins": [+      {+        "number": "1",+        "name": "VIN",+        "type": "power_in",+        "description": "Input supply voltage for the IC; operating range is 4.5 V to 75 V absolute maximum 76 V."+      },+      {+        "number": "2",+        "name": "EN",+        "type": "input",+        "description": "Enable input with tri-level control: below 0.4 V shutdown, 0.4 V to 1.2 V standby mode, above 1.2 V operational, with 5-µA internal pull-up current."+      },+      {+        "number": "3",+        "name": "SS",+        "type": "input",+        "description": "Soft start input; internal 11-µA current source charges external capacitor, with 1.2 V reference and 120 mV clamp above FB voltage."+      },+      {+        "number": "4",+        "name": "RAMP",+        "type": "output",+        "description": "Ramp generator output; external 100 pF to 2000 pF capacitor connected to GND sets emulated current ramp slope for peak current mode control."+      },+      {+        "number": "5",+        "name": "RT/SYNC",+        "type": "input",+        "description": "Oscillator frequency set and synchronization input; internal resistor to GND programs switching frequency 50 kHz to 1 MHz, external sync pulse width less than 150 ns."+      },+      {+        "number": "6",+        "name": "GND",+        "type": "power_in",+        "description": "Ground return; signal and power ground reference for the controller."+      },+      {+        "number": "7",+        "name": "COMP",+        "type": "output",+        "description": "Error amplifier output; internal 60 dB gain amplifier with 3 MHz unity-gain bandwidth, loop compensation network connected between COMP and FB pins."+      },+      {+        "number": "8",+        "name": "FB",+        "type": "input",+        "description": "Feedback signal input to inverting input of error amplifier with 1.205 V regulation threshold and ±18 nA maximum input bias current."+      },+      {+        "number": "9",+        "name": "OUT",+        "type": "input",+        "description": "Output voltage sensing input; connect directly to regulated output voltage to provide VIN-VOUT feedback for ramp generator compensation."+      },+      {+        "number": "10",+        "name": "RES",+        "type": "output",+        "description": "Restart timer output for hiccup mode (LM5088-2 only); external capacitor sets restart delay with 50-µA charge and 25-µA discharge current sources, 1.2 V upper and 0.2 V lower thresholds."+      },+      {+        "number": "11",+        "name": "CSG",+        "type": "power_in",+        "description": "Current sense ground; low-side reference terminal for external current sense resistor connected between CS and CSG pins."+      },+      {+        "number": "12",+        "name": "CS",+        "type": "input",+        "description": "Current sense input measuring re-circulating diode current with internal sample-and-hold circuit and 120 mV cycle-by-cycle current limit threshold."+      },+      {+        "number": "13",+        "name": "SW",+        "type": "output",+        "description": "Switching node output; connect directly to source terminal of external MOSFET switch and free-wheeling diode anode."+      },+      {+        "number": "14",+        "name": "HG",+        "type": "output",+        "description": "High-side gate driver output; 1.5 A peak source and 2 A peak sink current with 12 ns rise and 6 ns fall time driving external MOSFET gate."+      },+      {+        "number": "15",+        "name": "BOOT",+        "type": "passive",+        "description": "Bootstrap capacitor connection; external 0.022 µF minimum ceramic capacitor required between BOOT and SW pins, charged from VCC via internal diode."+      },+      {+        "number": "16",+        "name": "VCC",+        "type": "power_out",+        "description": "Bias regulator output; 7.8 V typical regulation from VIN with 30 mA internal current limit, requires 0.1 µF to 10 µF ceramic decoupling capacitor."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed thermal pad; electrically isolated must be soldered to ground plane to reduce thermal resistance per thermal analysis recommendations."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Pin 9 (OUT) description in datasheet states 'Connect this pin directly to the regulated output volta; Pin 10 identified as RES (Restart Version) per LM5088-2 variant; confirm part number suffix -2 match"+        ],+        "pages_sent": 45,+        "cost_usd": 0.4284,+        "at": "2026-09-23T13:12:51"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm5088",+        "pages": 45,+        "sha256": "7f168fca38f1dc8e",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file