← Commit history
README.mdadded+60@@ -0,0 +1,60 @@+# LM5025AMTCX++**Texas Instruments** · DC-DC Converters · TSSOP-16++LM5025AMTCX from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN | power_in | Source input voltage to the internal high-voltage start-up regulator. Operating range 13 V to 90 V, with transient capability to 105 V. |+| 2 | RAMP | input | Modulator ramp input. An external RC circuit from VIN sets the ramp slope; the pin is discharged each cycle by an internal FET triggered by the clock or the Volt-Second clamp comparator. |+| 3 | CS1 | input | Current sense input for cycle-by-cycle current limiting. Outputs enter cycle-by-cycle limit if CS1 exceeds 0.5 V; held low for 50 ns after OUT_A rises (leading-edge blanking). |+| 4 | CS2 | input | Current sense input for soft restart / cycle skip. If CS2 exceeds 0.5 V the outputs are disabled and a soft-start sequence is initiated; SS is fully discharged then released with a 1-µA pull-up. |+| 5 | TIME | input | Output overlap and dead-time control. An RSET resistor from TIME to GND produces in-phase OUT_A/OUT_B with overlap; RSET from TIME to REF produces out-of-phase OUT_A/OUT_B with dead time. |+| 6 | REF | power_out | Precision 5-V reference output. Sourcing up to 10 mA; decouple locally with a 0.1-µF capacitor. Remains low until VCC UV comparator is satisfied. |+| 7 | VCC | power_in | Output of the internal high-voltage start-up regulator, nominally regulated to 7.6 V. Also the bias supply input for the IC; an auxiliary winding raising VCC above the regulation setpoint shuts down the internal start-up regulator to reduce dissipation. |+| 8 | OUT_A | output | Main switch PWM gate-driver output. 3-A peak sink capability. |+| 9 | OUT_B | output | Active clamp switch gate-driver output. 1.25-A peak sink capability. |+| 10 | PGND | power_in | Power ground return for the gate drivers. Connect directly to AGND at a single point. |+| 11 | AGND | power_in | Analog ground for the control circuitry. Connect directly to PGND; on the WSON package the exposed pad is electrically connected to AGND. |+| 12 | SS | input | Soft-start control. An external capacitor with the internal 20-µA source sets the soft-start ramp; source drops to 1 µA after CS2 overcurrent or over-temperature events. |+| 13 | COMP | input | PWM comparator input. Includes an internal 5-kΩ pull-up; an external opto-coupler sinks current from COMP to control the PWM duty cycle. |+| 14 | RT | input | Oscillator timing resistor pin. An external resistor from RT to GND sets the internal oscillator frequency (up to 1 MHz). |+| 15 | SYNC | input | Oscillator UP/DOWN synchronization input. Accepts an external clock whose frequency is up to 20% lower than or higher than the internal free-running frequency; no maximum sync-frequency constraint. |+| 16 | UVLO | input | Line undervoltage shutdown input. External divider sets the shutdown threshold (comparator trip 2.5 V); hysteresis provided by a 20-µA internal current source switched at the 2.5-V threshold. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-16 |+| Category | PMIC |+| Pins | 16 |++## Ordering variants++Same part, different packaging or reel option.++- `LM5025AMTCX`+- `LM5025AMTCXSQ`+- `LM5025AMTCXSQE`+- `LM5025AMTCXSQX`++## CAD (KiCad official)++- Symbol: `LM5025AMTCX`+- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`+- 3D model: TSSOP-16 (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm5025amtcx.pdf) (34 pp, sha256 `970dbd727e87b319`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm5025amtcx-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "lm5025amtcx",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, TSSOP-16. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "pmic",+ "lm5025amtcx"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lm5025amtcx.kicad_sym",+ "lm5025amtcx.kicad_mod",+ "lm5025amtcx.glb",+ "lm5025amtcx.step",+ "lm5025amtcx.lbr",+ "docs/hero.png",+ "docs/lm5025amtcx-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}