← Commit history

Initial commit: component/lm43602pwpr

Ray ·a8cb10cca7 ·
2 files changed +93
README.mdadded+59
@@ -0,0 +1,59 @@+# LM43602PWPR++**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP++LM43602PWPR from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SW | power_out | Switching node output of the regulator, internally connected to both power MOSFETs. Connect to the external power inductor. Pins 1 and 2 are shorted internally. |+| 2 | SW | power_out | Switching node output of the regulator, internally connected to both power MOSFETs. Connect to the external power inductor. Pins 1 and 2 are shorted internally. |+| 3 | CBOOT | passive | Boot-strap capacitor connection for the high-side gate driver. Connect a high quality 470-nF capacitor from CBOOT to SW. |+| 4 | VCC | power_out | Internal bias supply output (approx. 3.28 V) for bypassing. Connect a bypass capacitor from this pin to AGND. Do not connect external loading; never short to ground during operation. |+| 5 | BIAS | power_in | Optional internal LDO supply input. Tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V, or to an external 3.3 V or 5 V rail, to improve efficiency. Place a 1-µF to 10-µF bypass capacitor to ground when used; tie to ground when not used. |+| 6 | SYNC | input | Clock input to synchronize switching action to an external clock. Use proper high-speed termination to prevent ringing. Connect to ground if not used. |+| 7 | RT | input | Switching frequency programming pin. Connect a resistor R_T from this pin to AGND to set the switching frequency between 200 kHz and 2.2 MHz. Leave floating for 500 kHz default. |+| 8 | PGOOD | output | Open-drain power-good flag output. Use a 10-kΩ to 100-kΩ pull-up resistor to a logic rail or other DC voltage no higher than 12 V. |+| 9 | FB | input | Feedback sense input pin. Connect to the midpoint of the external feedback divider to set VOUT. Do not short this pin to ground during operation. |+| 10 | AGND | power_in | Analog ground pin. Ground reference for internal references and logic. Connect to system ground. |+| 11 | SS/TRK | input | Soft-start / tracking control pin. Leave floating for the internal 4.1-ms soft-start slew rate. Connect a capacitor to extend soft-start time, or connect to an external voltage ramp for output tracking. |+| 12 | EN | input | Precision enable input to the internal LDO and regulator. High = ON, low = OFF. Connect to VIN, or to VIN through a resistor divider (for programmable UVLO), or to an external voltage/logic source. Do not float. |+| 13 | VIN | power_in | Supply input pin to the internal LDO and the high-side power FET (3.5 V to 36 V operating, 42 V abs max). Connect to the input supply and bypass capacitor C_IN. Pins 13 and 14 are shorted internally; the path from VIN to high-frequency bypass C_IN and PGND must be as short as possible. |+| 14 | VIN | power_in | Supply input pin to the internal LDO and the high-side power FET (3.5 V to 36 V operating, 42 V abs max). Connect to the input supply and bypass capacitor C_IN. Pins 13 and 14 are shorted internally; the path from VIN to high-frequency bypass C_IN and PGND must be as short as possible. |+| 15 | PGND | power_in | Power ground pin, connected internally to the low-side power FET. Connect to system ground, PAD, AGND, and the ground pins of C_IN and C_OUT. Path to C_IN must be as short as possible. |+| 16 | PGND | power_in | Power ground pin, connected internally to the low-side power FET. Connect to system ground, PAD, AGND, and the ground pins of C_IN and C_OUT. Path to C_IN must be as short as possible. |+| 17 | PAD | power_in | Exposed thermal pad. Low-impedance connection to AGND; connect to PGND on the PCB. Major heat-dissipation path of the die; must be soldered to a copper ground plane for thermal performance. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | PMIC |+| Pins | 17 |++## Ordering variants++Same part, different packaging or reel option.++- `LM43602PWPR`+- `LM43602PWPRDSU`++## CAD (KiCad official)++- Symbol: `LM43602PWPR`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lm43602pwpr.pdf) (49 pp, sha256 `a3b4d1cca14b806e`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm43602pwpr-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "lm43602pwpr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "lm43602pwpr"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm43602pwpr.kicad_sym",+    "lm43602pwpr.kicad_mod",+    "lm43602pwpr.glb",+    "lm43602pwpr.step",+    "lm43602pwpr.lbr",+    "docs/hero.png",+    "docs/lm43602pwpr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file