← Commit history

Initial commit: component/lm43602pwp

Ray ·6bb43a23b2 ·
2 files changed +267
README.mdadded+54
@@ -0,0 +1,54 @@+# LM43602PWP++**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP++LM43602PWP from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SW | output | Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor. |+| 2 | SW | output | Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor. |+| 3 | CBOOT | passive | Bootstrap capacitor connection for high-side driver; connect 470-nF capacitor from CBOOT to SW pin. |+| 4 | VCC | power_out | Internal bias supply output regulated at 3.2 V nominal; connect 2.2-10 µF bypass capacitor to AGND, never short or load this pin. |+| 5 | BIAS | power_in | Optional internal LDO supply input; tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V, external 3.3-5 V rail if available, or tie to ground when not in use. |+| 6 | SYNC | input | Clock input to synchronize switching action to external clock 200-2200 kHz; use high-speed termination to prevent ringing, ground if not used. |+| 7 | RT | passive | Connect resistor from this pin to AGND to program switching frequency 200-2200 kHz; leave floating for 500 kHz default. |+| 8 | PGOOD | output | Open-drain output for power-good flag; use 10-100 kΩ pull-up resistor to logic rail or DC voltage no higher than 12 V. |+| 9 | FB | input | Feedback sense input pin; connect to midpoint of feedback divider to set VOUT, do not short this pin to ground during operation. |+| 10 | AGND | power_in | Analog ground pin; ground reference for internal references and logic, connect to system ground. |+| 11 | SS/TRK | input | Soft-start control pin; leave floating for 4.1 ms internal soft-start ramp, or connect capacitor to extend or external voltage ramp for tracking. |+| 12 | EN | input | Enable input to internal LDO and regulator; high = ON, low = OFF; connect to VIN or external voltage source, do not float. |+| 13 | VIN | power_in | Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible. |+| 14 | VIN | power_in | Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible. |+| 15 | PGND | power_in | Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths. |+| 16 | PGND | power_in | Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths. |+| 17 | PAD | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Power Management (PMIC) |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `LM43602PWP`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `lm43602pwp-etched.step` / `lm43602pwp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm43602pwp.step` / `lm43602pwp.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm43602) (52 pp, sha256 `7057c203046aa5b7`, retrieved 2026-09-27, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm43602pwp-datasheet.pdf)
page.jsonadded+213
@@ -0,0 +1,213 @@+{+  "slug": "lm43602pwp",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "lm43602pwp",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm43602pwp.kicad_sym",+    "lm43602pwp.kicad_mod",+    "lm43602pwp.glb",+    "lm43602pwp.step",+    "lm43602pwp.lbr",+    "docs/hero.png",+    "docs/lm43602pwp-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM43602PWP",+    "manufacturer": "Texas Instruments",+    "package": "HTSSOP-16-EP",+    "pin_count": 17,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm43602",+    "parts": {+      "symbol": "lm43602pwp.kicad_sym",+      "footprint": "lm43602pwp.kicad_mod",+      "model_3d": "lm43602pwp-etched.glb",+      "model_3d_plain": "lm43602pwp.glb",+      "model_3d_step": "lm43602pwp-etched.step",+      "model_3d_step_plain": "lm43602pwp.step",+      "lbr": "lm43602pwp.lbr"+    },+    "distributor_links": {+      "lcsc": "C1355457",+      "digikey": "296-46517-5-ND",+      "mouser": "595-LM43602PWP"+    },+    "distributor_check": {+      "checked_at": "2026-09-27T11:12:28Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-46517-5-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "595-LM43602PWP",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "SW",+        "type": "output",+        "description": "Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor."+      },+      {+        "number": "2",+        "name": "SW",+        "type": "output",+        "description": "Switching output of the regulator internally connected to both power MOSFETs; connect to power inductor."+      },+      {+        "number": "3",+        "name": "CBOOT",+        "type": "passive",+        "description": "Bootstrap capacitor connection for high-side driver; connect 470-nF capacitor from CBOOT to SW pin."+      },+      {+        "number": "4",+        "name": "VCC",+        "type": "power_out",+        "description": "Internal bias supply output regulated at 3.2 V nominal; connect 2.2-10 µF bypass capacitor to AGND, never short or load this pin."+      },+      {+        "number": "5",+        "name": "BIAS",+        "type": "power_in",+        "description": "Optional internal LDO supply input; tie to VOUT when 3.3 V ≤ VOUT ≤ 28 V, external 3.3-5 V rail if available, or tie to ground when not in use."+      },+      {+        "number": "6",+        "name": "SYNC",+        "type": "input",+        "description": "Clock input to synchronize switching action to external clock 200-2200 kHz; use high-speed termination to prevent ringing, ground if not used."+      },+      {+        "number": "7",+        "name": "RT",+        "type": "passive",+        "description": "Connect resistor from this pin to AGND to program switching frequency 200-2200 kHz; leave floating for 500 kHz default."+      },+      {+        "number": "8",+        "name": "PGOOD",+        "type": "output",+        "description": "Open-drain output for power-good flag; use 10-100 kΩ pull-up resistor to logic rail or DC voltage no higher than 12 V."+      },+      {+        "number": "9",+        "name": "FB",+        "type": "input",+        "description": "Feedback sense input pin; connect to midpoint of feedback divider to set VOUT, do not short this pin to ground during operation."+      },+      {+        "number": "10",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground pin; ground reference for internal references and logic, connect to system ground."+      },+      {+        "number": "11",+        "name": "SS/TRK",+        "type": "input",+        "description": "Soft-start control pin; leave floating for 4.1 ms internal soft-start ramp, or connect capacitor to extend or external voltage ramp for tracking."+      },+      {+        "number": "12",+        "name": "EN",+        "type": "input",+        "description": "Enable input to internal LDO and regulator; high = ON, low = OFF; connect to VIN or external voltage source, do not float."+      },+      {+        "number": "13",+        "name": "VIN",+        "type": "power_in",+        "description": "Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible."+      },+      {+        "number": "14",+        "name": "VIN",+        "type": "power_in",+        "description": "Supply input pin 3.5-36 V to internal LDO and high-side FET; keep paths from VIN pin to bypass CIN and PGND as short as possible."+      },+      {+        "number": "15",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths."+      },+      {+        "number": "16",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground pin connected internally to low-side FET; connect to system ground, PAD, AGND, and CIN/COUT ground pins with shortest paths."+      },+      {+        "number": "17",+        "name": "PAD",+        "type": "passive",+        "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "exposed pad 17 added from the footprint",+          "dropped thermal pad ['EP'] absent from footprint"+        ],+        "pages_sent": 52,+        "cost_usd": 0.4443,+        "at": "2026-09-27T11:12:10"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm43602",+        "pages": 52,+        "sha256": "7057c203046aa5b7",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file