← Commit history
lm3478mmx: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+75−1
page.json+75−1@@ -33,5 +33,79 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "LM3478MMX",+ "manufacturer": "Texas Instruments",+ "package": "VSSOP-8-0.65mm",+ "pin_count": 8,+ "category": "AC-DC Controllers and Regulators",+ "datasheet": "https://www.ti.com/lit/ds/symlink/lm3478mmx.pdf",+ "parts": {+ "symbol": "lm3478mmx.kicad_sym",+ "footprint": "lm3478mmx.kicad_mod",+ "model_3d": "lm3478mmx-etched.glb",+ "model_3d_plain": "lm3478mmx.glb",+ "model_3d_step": "lm3478mmx-etched.step",+ "model_3d_step_plain": "lm3478mmx.step",+ "lbr": "lm3478mmx.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "ISEN",+ "type": "input",+ "description": "Current sense input pin. The voltage generated across an external sense resistor (RSEN) in series with the source of the external N-channel MOSFET is fed into this pin for cycle-by-cycle current-mode control and current limiting. Absolute maximum pin voltage is 500 mV."+ },+ {+ "number": "2",+ "name": "COMP",+ "type": "output",+ "description": "Compensation pin. A series resistor-capacitor network connected from this pin to AGND provides frequency compensation for the current-mode control loop. This pin is the output of the internal transconductance error amplifier."+ },+ {+ "number": "3",+ "name": "FB",+ "type": "input",+ "description": "Feedback pin. Inverting input of the internal error amplifier; the output voltage should be adjusted using an external resistor divider to provide 1.26 V (nominal internal reference) at this pin. Absolute max: -0.4 V to 7 V."+ },+ {+ "number": "4",+ "name": "AGND",+ "type": "power_in",+ "description": "Analog ground pin. Reference for the internal reference, error amplifier, and other small-signal circuitry. Should be tied to PGND at a single point (typically at the input capacitor return) to avoid ground loop noise."+ },+ {+ "number": "5",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground pin. Return path for the high-current internal MOSFET gate driver (DR pin). Should be routed with a low-impedance connection back to the source of the external MOSFET / sense resistor."+ },+ {+ "number": "6",+ "name": "DR",+ "type": "output",+ "description": "Drive pin. Output of the internal push-pull gate driver (1-A peak current capability) that drives the gate of the external low-side N-channel MOSFET. Pin voltage range is -0.4 V to 8 V (internally clamped for gate protection)."+ },+ {+ "number": "7",+ "name": "FA/SD",+ "type": "input",+ "description": "Frequency-adjust and shutdown pin. A resistor from this pin to AGND sets the internal oscillator frequency between 100 kHz and 1 MHz. Driving this pin high for longer than 30 µs shuts the device down, reducing supply current to less than 10 µA. Absolute max: -0.4 V to 7 V."+ },+ {+ "number": "8",+ "name": "VIN",+ "type": "power_in",+ "description": "Power supply input pin. Provides bias to the internal control circuitry and the gate driver. Recommended operating range 2.97 V to 40 V; absolute maximum 45 V. Should be bypassed with a local ceramic capacitor to PGND."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}