← Commit history
page.json+158−8@@ -1,13 +1,168 @@ {+ "schema_version": 1,+ "type": "component", "slug": "lm3150mhx",+ "title": "LM3150MHX",+ "brief": "Texas Instruments DC-DC Converters, HTSSOP-14-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.", "version": "0.1.0",- "type": "component",- "description": "Texas Instruments DC-DC Converters, HTSSOP-14-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "license": "CC-BY-SA-4.0", "tags": [ "component", "pmic", "lm3150mhx" ],+ "component": {+ "mpn": "LM3150MHX",+ "manufacturer": "Texas Instruments",+ "package": "HTSSOP-14-EP",+ "pin_count": 15,+ "category": "PMIC",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/lit/ds/symlink/lm3150mhx.pdf",+ "parts": {+ "symbol": "lm3150mhx.kicad_sym",+ "footprint": "lm3150mhx.kicad_mod",+ "model_3d": "lm3150mhx.glb",+ "model_3d_step": "lm3150mhx.step",+ "lbr": "lm3150mhx.lbr"+ },+ "distributor_links": {},+ "pins": [+ {+ "number": "1",+ "name": "VCC",+ "type": "power_out",+ "description": "Internal LDO output supplying the FET gate drivers and internal bias. Nominally regulated to 5.95 V. Connect a 1.0 \u00b5F to 4.7 \u00b5F decoupling capacitor from this pin to ground."+ },+ {+ "number": "2",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply pin to the device. Nominal input voltage range is 6 V to 42 V (abs max 47 V)."+ },+ {+ "number": "3",+ "name": "EN",+ "type": "input",+ "description": "Enable input. Apply a logic-high signal greater than 1.26 V (typ) to enable the IC, or leave floating. Ground this pin to disable the controller. Recommended operating range 0 V to 5 V."+ },+ {+ "number": "4",+ "name": "FB",+ "type": "input",+ "description": "Feedback input to the regulation, overvoltage, and short-circuit comparators. Regulation setting is 0.6 V. Connect to a feedback resistor divider from the output to set VOUT."+ },+ {+ "number": "5",+ "name": "SGND",+ "type": "power_in",+ "description": "Signal ground for all internal bias and reference circuitry. Should be tied to PGND at a single point. Pin 5 and pin 9 are both SGND and must be connected together."+ },+ {+ "number": "6",+ "name": "SS",+ "type": "passive",+ "description": "Soft-start capacitor node. An internal 7.7 \u00b5A current source charges an external capacitor from this pin to ground to program the output ramp rate at start-up."+ },+ {+ "number": "7",+ "name": "RON",+ "type": "input",+ "description": "On-time programming pin. An external resistor from VIN to this pin sets the high-side switch on-time and therefore the switching frequency."+ },+ {+ "number": "8",+ "name": "ILIM",+ "type": "input",+ "description": "Current-limit sense input. Monitors the low-side FET current and triggers current-limit operation when the inductor valley current exceeds the threshold set by R_LIM and the 85 \u00b5A (typ) I_LIM-TH sense current sourced from this pin."+ },+ {+ "number": "9",+ "name": "SGND",+ "type": "power_in",+ "description": "Signal ground (second connection). Tie to PGND at a single point. Must be connected to pin 5."+ },+ {+ "number": "10",+ "name": "SW",+ "type": "power_in",+ "description": "Switch node. Connection to the source of the high-side NMOS and drain of the low-side NMOS, and lower supply rail for the high-side gate driver. Boost capacitor (BST) is referenced to this pin. Abs max \u22123 V to 47 V."+ },+ {+ "number": "11",+ "name": "HG",+ "type": "output",+ "description": "High-side NMOS gate drive output. Driver is supplied by the differential voltage between BST and SW (typically ~5.95 V bootstrap rail)."+ },+ {+ "number": "12",+ "name": "BST",+ "type": "power_in",+ "description": "Bootstrap capacitor connection. Connect a 0.33 \u00b5F to 0.47 \u00b5F capacitor from SW to this pin. An internal diode charges the cap during the high-side off-time. Do not connect to an external supply rail. Abs max BST-SW 7 V; BST-GND 52 V."+ },+ {+ "number": "13",+ "name": "LG",+ "type": "output",+ "description": "Low-side NMOS gate drive output. Driver upper rail is supplied by VCC (~5.95 V)."+ },+ {+ "number": "14",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground; source connection for the synchronous low-side MOSFET driver. Tie to the power ground plane and to SGND at a single point."+ },+ {+ "number": "EP",+ "name": "EP",+ "type": "passive",+ "description": "Exposed die-attach thermal pad. Connect directly to SGND and to the PCB ground plane for heat dissipation."+ }+ ],+ "provenance": {+ "extractor": "ds2sf",+ "datasheet": {+ "url": "https://www.ti.com/lit/ds/symlink/lm3150mhx.pdf",+ "pages": 32,+ "sha256": "262f4efa528d8294",+ "source_tier": "mfr"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 15,+ "described": 15,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ }+ },+ "metadata": {+ "specs": {+ "Manufacturer": "Texas Instruments",+ "Package": "HTSSOP-14-EP",+ "Category": "PMIC",+ "Pins": "15"+ }+ },+ "sections": [+ "hero",+ "viewers",+ "readme",+ "breadcrumbs",+ "info"+ ],+ "discovery_triggers": [+ "lm3150mhx"+ ],+ "discovery_pitch": "LM3150MHX (Texas Instruments) component page with datasheet-verified CAD.",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }, "dependencies": {}, "hero": { "type": "image",@@ -25,10 +180,5 @@ "docs/lm3150mhx-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ],- "visibility": "public",- "author": {- "name": "Ray",- "email": "[email protected]"- }+ ] }