← Commit history
lm2852ymxax-1-5: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+117−1
page.json+117−1@@ -33,5 +33,121 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "LM2852YMXAX-1.5",+ "manufacturer": "Texas Instruments LM2852YMXAX 1 5 NOPB",+ "package": "HTSSOP-14-EP",+ "pin_count": 15,+ "category": "DC-DC Converters",+ "datasheet": "https://www.ti.com/lit/ds/symlink/lm2852ymxax-1.5.pdf",+ "parts": {+ "symbol": "lm2852ymxax-1-5.kicad_sym",+ "footprint": "lm2852ymxax-1-5.kicad_mod",+ "model_3d": "lm2852ymxax-1-5-etched.glb",+ "model_3d_plain": "lm2852ymxax-1-5.glb",+ "model_3d_step": "lm2852ymxax-1-5-etched.step",+ "model_3d_step_plain": "lm2852ymxax-1-5.step",+ "lbr": "lm2852ymxax-1-5.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "AVIN",+ "type": "power_in",+ "description": "Chip bias / analog input supply. Powers the internal control logic and analog circuitry. Connect to the input voltage (2.85 V to 5.5 V) or a separate rail; filter close to the pin."+ },+ {+ "number": "2",+ "name": "EN",+ "type": "input",+ "description": "Enable input. Drive low (to GND) to disable the regulator; drive high (to AVIN) or leave floating to enable it. Pin is internally pulled up."+ },+ {+ "number": "3",+ "name": "SGND",+ "type": "power_in",+ "description": "Signal (analog) ground reference for the internal control circuitry. Tie to the PGND / ground plane at a single point near the device."+ },+ {+ "number": "4",+ "name": "SS",+ "type": "passive",+ "description": "Soft-start pin. Connect a small capacitor (1 nF to 50 nF) to ground to program the startup ramp. Internal soft-start resistance is ~400 kΩ."+ },+ {+ "number": "5",+ "name": "NC",+ "type": "unconnected",+ "description": "No connect. Must be tied to ground or left floating in the application."+ },+ {+ "number": "6",+ "name": "PVIN",+ "type": "power_in",+ "description": "Power input to the internal high-side PFET switch (source connection). Bypass with a low-ESR ceramic capacitor (e.g. 22 µF) close to the pin. Must be tied together with pin 7."+ },+ {+ "number": "7",+ "name": "PVIN",+ "type": "power_in",+ "description": "Power input to the internal high-side PFET switch (source connection). Must be tied together with pin 6 on the PCB."+ },+ {+ "number": "8",+ "name": "SW",+ "type": "power_out",+ "description": "Switch node - drain of the internal high-side PFET and low-side NFET. Connect through the output inductor (e.g. 10 µH) to the load. Must be tied together with pin 9."+ },+ {+ "number": "9",+ "name": "SW",+ "type": "power_out",+ "description": "Switch node. Must be tied together with pin 8 on the PCB."+ },+ {+ "number": "10",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground - return for the low-side NFET switch current. Connect to a large ground plane; must be tied together with pin 11."+ },+ {+ "number": "11",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground - return for the low-side NFET switch current. Must be tied together with pin 10."+ },+ {+ "number": "12",+ "name": "NC",+ "type": "unconnected",+ "description": "No connect. Must be tied to ground or left floating in the application."+ },+ {+ "number": "13",+ "name": "NC",+ "type": "unconnected",+ "description": "No connect. Must be tied to ground or left floating in the application."+ },+ {+ "number": "14",+ "name": "SNS",+ "type": "input",+ "description": "Output voltage sense pin. Connect Kelvin-style to VOUT as close to the load as possible; internal sense resistance is ~400 kΩ. This is the regulation feedback point."+ },+ {+ "number": "15",+ "name": "EP",+ "type": "power_in",+ "description": "Exposed thermal pad on the underside of the HTSSOP-14 (PowerPAD) package. Must be soldered to a large ground plane / thermal-pad copper for heat dissipation and connected to ground."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}