← Commit history

Initial commit: component/lm26480sqx-aa

Ray ·3e575ae2ed ·
2 files changed +305
README.mdadded+62
@@ -0,0 +1,62 @@+# LM26480SQX-AA++**Texas Instruments** · DC-DC Converters · WQFN-24-EP(4x4)++LM26480SQX-AA from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VINLDO12 | power_in | Analog power supply for internal reference, bias, and logic circuits; requires 2.8V to 5.5V |+| 2 | SYNC | input | External oscillator synchronization input operating range 10.4 MHz to 15.6 MHz; must be grounded when not used |+| 3 | NPOR | tri_state | Open-drain power-on reset output for Buck1 and Buck2; pulled to ground when output voltages fall below specification with programmable delay of 60 ms default |+| 4 | GND_SW1 | power_in | Buck1 NMOS switching power ground |+| 5 | SW1 | power_out | Buck1 synchronous step-down converter output; programmable 0.8V to 2V with 1.5A maximum output current |+| 6 | VIN1 | power_in | Buck1 power input from DC source or battery; accepts 2.8V to 5.5V |+| 7 | ENSW1 | input | Buck1 enable input; logic HIGH enables converter operation; pin cannot be left floating |+| 8 | FB1 | input | Buck1 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3% |+| 9 | GND_C | power_in | Non-switching core ground for analog and control circuits |+| 10 | AVDD | power_in | Analog power supply for Buck converter control circuits; requires 2.8V to 5.5V |+| 11 | FB2 | input | Buck2 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3% |+| 12 | ENSW2 | input | Buck2 enable input; logic HIGH enables converter operation; pin cannot be left floating |+| 13 | VIN2 | power_in | Buck2 power input from DC source or battery; accepts 2.8V to 5.5V |+| 14 | SW2 | power_out | Buck2 synchronous step-down converter output; programmable 1V to 3.3V with 1.5A maximum output current |+| 15 | GND_SW2 | power_in | Buck2 NMOS switching power ground |+| 16 | ENLDO2 | input | LDO2 enable input; logic HIGH enables regulator operation; pin cannot be left floating |+| 17 | ENLDO1 | input | LDO1 enable input; logic HIGH enables regulator operation; pin cannot be left floating |+| 18 | GND_L | power_in | LDO linear regulator ground |+| 19 | VINLDO1 | power_in | LDO1 power input from DC source or battery; requires minimum 1.74V when enabled, maximum 5.5V |+| 20 | LDO1 | power_out | LDO1 regulated output; programmable 1V to 3.5V with 300mA maximum output current and 25mV typical dropout voltage |+| 21 | FBL1 | input | LDO1 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3% |+| 22 | FBL2 | input | LDO2 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3% |+| 23 | LDO2 | power_out | LDO2 regulated output; programmable 1V to 3.5V with 300mA maximum output current and 25mV typical dropout voltage |+| 24 | VINLDO2 | power_in | LDO2 power input from DC source or battery; requires minimum 1.74V when enabled, maximum 5.5V |+| 25 | DAP | power_in | Exposed thermal die attach pad for improved thermal dissipation; soldering to PCB recommended for thermal and mechanical performance |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WQFN-24-EP(4x4) |+| Category | Power Management (PMIC) |+| Pins | 25 |++## CAD (KiCad official)++- Symbol: `LM26480SQX-AA`+- Footprint: `Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm`+- 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)+- 3D model files: `lm26480sqx-aa-etched.step` / `lm26480sqx-aa-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm26480sqx-aa.step` / `lm26480sqx-aa.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm26480) (44 pp, sha256 `9fa8e8bf5131003e`, retrieved 2026-09-23, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm26480sqx-aa-datasheet.pdf)
page.jsonadded+243
@@ -0,0 +1,243 @@+{+  "slug": "lm26480sqx-aa",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Converters, WQFN-24-EP(4x4). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power management (pmic)",+    "lm26480sqx-aa",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm26480sqx-aa.kicad_sym",+    "lm26480sqx-aa.kicad_mod",+    "lm26480sqx-aa.glb",+    "lm26480sqx-aa.step",+    "lm26480sqx-aa.lbr",+    "docs/hero.png",+    "docs/lm26480sqx-aa-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM26480SQX-AA",+    "manufacturer": "Texas Instruments",+    "package": "WQFN-24-EP(4x4)",+    "pin_count": 25,+    "category": "Power Management (PMIC)",+    "subcategory": "DC-DC Converters",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm26480",+    "parts": {+      "symbol": "lm26480sqx-aa.kicad_sym",+      "footprint": "lm26480sqx-aa.kicad_mod",+      "model_3d": "lm26480sqx-aa-etched.glb",+      "model_3d_plain": "lm26480sqx-aa.glb",+      "model_3d_step": "lm26480sqx-aa-etched.step",+      "model_3d_step_plain": "lm26480sqx-aa.step",+      "lbr": "lm26480sqx-aa.lbr"+    },+    "distributor_links": {+      "lcsc": "C2876374"+    },+    "pins": [+      {+        "number": "1",+        "name": "VINLDO12",+        "type": "power_in",+        "description": "Analog power supply for internal reference, bias, and logic circuits; requires 2.8V to 5.5V"+      },+      {+        "number": "2",+        "name": "SYNC",+        "type": "input",+        "description": "External oscillator synchronization input operating range 10.4 MHz to 15.6 MHz; must be grounded when not used"+      },+      {+        "number": "3",+        "name": "NPOR",+        "type": "tri_state",+        "description": "Open-drain power-on reset output for Buck1 and Buck2; pulled to ground when output voltages fall below specification with programmable delay of 60 ms default"+      },+      {+        "number": "4",+        "name": "GND_SW1",+        "type": "power_in",+        "description": "Buck1 NMOS switching power ground"+      },+      {+        "number": "5",+        "name": "SW1",+        "type": "power_out",+        "description": "Buck1 synchronous step-down converter output; programmable 0.8V to 2V with 1.5A maximum output current"+      },+      {+        "number": "6",+        "name": "VIN1",+        "type": "power_in",+        "description": "Buck1 power input from DC source or battery; accepts 2.8V to 5.5V"+      },+      {+        "number": "7",+        "name": "ENSW1",+        "type": "input",+        "description": "Buck1 enable input; logic HIGH enables converter operation; pin cannot be left floating"+      },+      {+        "number": "8",+        "name": "FB1",+        "type": "input",+        "description": "Buck1 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"+      },+      {+        "number": "9",+        "name": "GND_C",+        "type": "power_in",+        "description": "Non-switching core ground for analog and control circuits"+      },+      {+        "number": "10",+        "name": "AVDD",+        "type": "power_in",+        "description": "Analog power supply for Buck converter control circuits; requires 2.8V to 5.5V"+      },+      {+        "number": "11",+        "name": "FB2",+        "type": "input",+        "description": "Buck2 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"+      },+      {+        "number": "12",+        "name": "ENSW2",+        "type": "input",+        "description": "Buck2 enable input; logic HIGH enables converter operation; pin cannot be left floating"+      },+      {+        "number": "13",+        "name": "VIN2",+        "type": "power_in",+        "description": "Buck2 power input from DC source or battery; accepts 2.8V to 5.5V"+      },+      {+        "number": "14",+        "name": "SW2",+        "type": "power_out",+        "description": "Buck2 synchronous step-down converter output; programmable 1V to 3.3V with 1.5A maximum output current"+      },+      {+        "number": "15",+        "name": "GND_SW2",+        "type": "power_in",+        "description": "Buck2 NMOS switching power ground"+      },+      {+        "number": "16",+        "name": "ENLDO2",+        "type": "input",+        "description": "LDO2 enable input; logic HIGH enables regulator operation; pin cannot be left floating"+      },+      {+        "number": "17",+        "name": "ENLDO1",+        "type": "input",+        "description": "LDO1 enable input; logic HIGH enables regulator operation; pin cannot be left floating"+      },+      {+        "number": "18",+        "name": "GND_L",+        "type": "power_in",+        "description": "LDO linear regulator ground"+      },+      {+        "number": "19",+        "name": "VINLDO1",+        "type": "power_in",+        "description": "LDO1 power input from DC source or battery; requires minimum 1.74V when enabled, maximum 5.5V"+      },+      {+        "number": "20",+        "name": "LDO1",+        "type": "power_out",+        "description": "LDO1 regulated output; programmable 1V to 3.5V with 300mA maximum output current and 25mV typical dropout voltage"+      },+      {+        "number": "21",+        "name": "FBL1",+        "type": "input",+        "description": "LDO1 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"+      },+      {+        "number": "22",+        "name": "FBL2",+        "type": "input",+        "description": "LDO2 feedback input terminal for external resistor divider; nominal feedback voltage 0.5V ±3%"+      },+      {+        "number": "23",+        "name": "LDO2",+        "type": "power_out",+        "description": "LDO2 regulated output; programmable 1V to 3.5V with 300mA maximum output current and 25mV typical dropout voltage"+      },+      {+        "number": "24",+        "name": "VINLDO2",+        "type": "power_in",+        "description": "LDO2 power input from DC source or battery; requires minimum 1.74V when enabled, maximum 5.5V"+      },+      {+        "number": "25",+        "name": "DAP",+        "type": "power_in",+        "description": "Exposed thermal die attach pad for improved thermal dissipation; soldering to PCB recommended for thermal and mechanical performance"+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 44,+        "cost_usd": 0.444,+        "at": "2026-09-23T19:01:27"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm26480",+        "pages": 44,+        "sha256": "9fa8e8bf5131003e",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 25,+        "described": 25,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file