component
LM26420XMH
Public Made by Adomby adom
Texas Instruments DC-DC Converters, HTSSOP-20-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+58@@ -0,0 +1,58 @@+# LM26420XMH++**Texas Instruments** · DC-DC Converters · HTSSOP-20-EP++LM26420XMH from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VINC | power_in | Input supply for the control circuitry; the recommended VIN range is 3 V to 5.5 V. |+| 2 | EN1 | input | Logic-high enable for Buck 1; do not allow this pin to float or be greater than VIN + 0.3 V. |+| 3 | VIND1 | power_in | Power input supply for Buck 1; the recommended VIN range is 3 V to 5.5 V. |+| 4 | VIND1 | power_in | Power input supply for Buck 1; the recommended VIN range is 3 V to 5.5 V. |+| 5 | SW1 | power_out | Output switch for Buck 1; connect to the inductor. |+| 6 | PGND1 | power_in | Power ground pin for Buck 1. |+| 7 | PGND1 | power_in | Power ground pin for Buck 1. |+| 8 | FB1 | input | Feedback pin for Buck 1; connect to an external resistor divider to set the output voltage. The absolute maximum rating for FB is -0.5 V to 3 V. |+| 9 | PG1 | output | Power-good indicator for Buck 1; open-drain output connected through a resistor to an external supply. |+| 10 | DAP | power_in | Die attach pad; connect to system ground for low thermal impedance, but it cannot be used as a primary GND connection. |+| 11 | DAP | power_in | Die attach pad; connect to system ground for low thermal impedance, but it cannot be used as a primary GND connection. |+| 12 | PG2 | output | Power-good indicator for Buck 2; open-drain output connected through a resistor to an external supply. |+| 13 | FB2 | input | Feedback pin for Buck 2; connect to an external resistor divider to set the output voltage. The absolute maximum rating for FB is -0.5 V to 3 V. |+| 14 | PGND2 | power_in | Power ground pin for Buck 2. |+| 15 | PGND2 | power_in | Power ground pin for Buck 2. |+| 16 | SW2 | power_out | Output switch for Buck 2; connect to the inductor. |+| 17 | VIND2 | power_in | Power input supply for Buck 2; the recommended VIN range is 3 V to 5.5 V. |+| 18 | VIND2 | power_in | Power input supply for Buck 2; the recommended VIN range is 3 V to 5.5 V. |+| 19 | EN2 | input | Logic-high enable for Buck 2; do not allow this pin to float or be greater than VIN + 0.3 V. |+| 20 | AGND | power_in | Signal ground pin; place the bottom resistor of the feedback network as close as possible to this pin. |+| 21 | DAP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-20-EP |+| Category | Power Supply Chip |+| Pins | 21 |++## CAD (KiCad official)++- Symbol: `LM26420XMH`+- Footprint: `Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm`+- 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)+- 3D model files: `lm26420xmh-etched.step` / `lm26420xmh-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm26420xmh.step` / `lm26420xmh.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm26420) (49 pp, sha256 `990c6ab4facbae3a`, retrieved 2026-10-08, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm26420xmh-datasheet.pdf)
page.jsonadded+276@@ -0,0 +1,276 @@+{+ "slug": "lm26420xmh",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, HTSSOP-20-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "lm26420xmh",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lm26420xmh.kicad_sym",+ "lm26420xmh.kicad_mod",+ "lm26420xmh.glb",+ "lm26420xmh.step",+ "lm26420xmh.lbr",+ "docs/hero.png",+ "docs/lm26420xmh-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "lm26420xmh-hero.glb",+ "lm26420xmh-hero.overlay.json"+ ],+ "component": {+ "mpn": "LM26420XMH",+ "manufacturer": "Texas Instruments",+ "package": "HTSSOP-20-EP",+ "pin_count": 21,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/lm26420",+ "parts": {+ "symbol": "lm26420xmh.kicad_sym",+ "footprint": "lm26420xmh.kicad_mod",+ "model_3d": "lm26420xmh-hero.glb",+ "model_3d_plain": "lm26420xmh.glb",+ "model_3d_step": "lm26420xmh-etched.step",+ "model_3d_step_plain": "lm26420xmh.step",+ "lbr": "lm26420xmh.lbr"+ },+ "distributor_links": {+ "lcsc": "C1355740"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T00:16:34Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": null,+ "status": "no match"+ },+ "mouser": {+ "pn": null,+ "status": "no match"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "VINC",+ "type": "power_in",+ "description": "Input supply for the control circuitry; the recommended VIN range is 3 V to 5.5 V."+ },+ {+ "number": "2",+ "name": "EN1",+ "type": "input",+ "description": "Logic-high enable for Buck 1; do not allow this pin to float or be greater than VIN + 0.3 V."+ },+ {+ "number": "3",+ "name": "VIND1",+ "type": "power_in",+ "description": "Power input supply for Buck 1; the recommended VIN range is 3 V to 5.5 V."+ },+ {+ "number": "4",+ "name": "VIND1",+ "type": "power_in",+ "description": "Power input supply for Buck 1; the recommended VIN range is 3 V to 5.5 V."+ },+ {+ "number": "5",+ "name": "SW1",+ "type": "power_out",+ "description": "Output switch for Buck 1; connect to the inductor."+ },+ {+ "number": "6",+ "name": "PGND1",+ "type": "power_in",+ "description": "Power ground pin for Buck 1."+ },+ {+ "number": "7",+ "name": "PGND1",+ "type": "power_in",+ "description": "Power ground pin for Buck 1."+ },+ {+ "number": "8",+ "name": "FB1",+ "type": "input",+ "description": "Feedback pin for Buck 1; connect to an external resistor divider to set the output voltage. The absolute maximum rating for FB is -0.5 V to 3 V."+ },+ {+ "number": "9",+ "name": "PG1",+ "type": "output",+ "description": "Power-good indicator for Buck 1; open-drain output connected through a resistor to an external supply."+ },+ {+ "number": "10",+ "name": "DAP",+ "type": "power_in",+ "description": "Die attach pad; connect to system ground for low thermal impedance, but it cannot be used as a primary GND connection."+ },+ {+ "number": "11",+ "name": "DAP",+ "type": "power_in",+ "description": "Die attach pad; connect to system ground for low thermal impedance, but it cannot be used as a primary GND connection."+ },+ {+ "number": "12",+ "name": "PG2",+ "type": "output",+ "description": "Power-good indicator for Buck 2; open-drain output connected through a resistor to an external supply."+ },+ {+ "number": "13",+ "name": "FB2",+ "type": "input",+ "description": "Feedback pin for Buck 2; connect to an external resistor divider to set the output voltage. The absolute maximum rating for FB is -0.5 V to 3 V."+ },+ {+ "number": "14",+ "name": "PGND2",+ "type": "power_in",+ "description": "Power ground pin for Buck 2."+ },+ {+ "number": "15",+ "name": "PGND2",+ "type": "power_in",+ "description": "Power ground pin for Buck 2."+ },+ {+ "number": "16",+ "name": "SW2",+ "type": "power_out",+ "description": "Output switch for Buck 2; connect to the inductor."+ },+ {+ "number": "17",+ "name": "VIND2",+ "type": "power_in",+ "description": "Power input supply for Buck 2; the recommended VIN range is 3 V to 5.5 V."+ },+ {+ "number": "18",+ "name": "VIND2",+ "type": "power_in",+ "description": "Power input supply for Buck 2; the recommended VIN range is 3 V to 5.5 V."+ },+ {+ "number": "19",+ "name": "EN2",+ "type": "input",+ "description": "Logic-high enable for Buck 2; do not allow this pin to float or be greater than VIN + 0.3 V."+ },+ {+ "number": "20",+ "name": "AGND",+ "type": "power_in",+ "description": "Signal ground pin; place the bottom resistor of the feedback network as close as possible to this pin."+ },+ {+ "number": "21",+ "name": "DAP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The HTSSOP-20 pin table lists pins 10 and 11 together with the DAP as one grouped row ('10, 11, DAP'; Pin types are mapped from the datasheet's P/A/G classes to KiCad ERC classes by function: SW as powe; Pin 4 and pin 7 etc. are shown as separate entries for pins sharing one name in the table (e.g. VIND",+ "exposed pad 21 added from the footprint"+ ],+ "pages_sent": 10,+ "cost_usd": 0.0715,+ "at": "2026-10-08T00:16:09"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/lm26420",+ "pages": 49,+ "sha256": "990c6ab4facbae3a",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 21,+ "described": 21,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lm26420xmh.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.41,+ 6.5,+ 1.2+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "88217c65b302bc983680b710977e332754ef391397359f9ae4287e77ddb0ffea",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lm26420xmh-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.41,+ 6.5,+ 1.2+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "9e82d66ac6f37aceae61a4d8531ddb8ec985fd0d9d3ac78251544d00630ed10b",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}