component
LM2594N-5.0
Public Made by Adomby adom
Texas Instruments DC-DC Converters, PDIP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+44@@ -0,0 +1,44 @@+# LM2594N-5.0++**Texas Instruments** · DC-DC Converters · PDIP-8++LM2594N-5.0 from Texas Instruments, in a PDIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | NC | unconnected | No connection; the datasheet notes NC pins are not internally connected but must be soldered to the PCB for best heat transfer. |+| 2 | NC | unconnected | No connection; the datasheet notes NC pins are not internally connected but must be soldered to the PCB for best heat transfer. |+| 3 | NC | unconnected | No connection; the datasheet notes NC pins are not internally connected but must be soldered to the PCB for best heat transfer. |+| 4 | Feedback | input | Senses the regulated output voltage to complete the feedback loop. |+| 5 | ON/OFF | input | Logic-level shutdown: pulling below about 1.3 V turns the regulator on and pulling above 1.3 V (up to a maximum of 25 V) shuts it down, reducing total input supply current to about 80 µA; leave open or tie to ground to keep the regulator always on. |+| 6 | Ground | power_in | Circuit ground. |+| 7 | +VIN | power_in | Positive input supply for the switching regulator, requiring a suitable input bypass capacitor at this pin; recommended operating supply is 4.5 V to 40 V for LM2594 (60 V for LM2594HV) with absolute maximum of 45 V for LM2594. |+| 8 | Output | output | Internal switch output that swings between (+VIN − VSAT) and approximately −0.5 V with duty cycle VOUT/VIN; keep the PCB copper area on this pin to a minimum to limit coupling to sensitive circuitry. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | PDIP-8 |+| Category | Power Management (PMIC) |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `LM2594N-5.0`+- Footprint: `Package_DIP:DIP-8_W7.62mm`+- 3D model: PDIP-8 (KiCad packages3D, STEP)+- 3D model files: `lm2594n-5-0-etched.step` / `lm2594n-5-0-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm2594n-5-0.step` / `lm2594n-5-0.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm2594) (48 pp, sha256 `f4ff0460f0a09cf3`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm2594n-5-0-datasheet.pdf)
page.jsonadded+202@@ -0,0 +1,202 @@+{+ "slug": "lm2594n-5-0",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, PDIP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power management (pmic)",+ "lm2594n-5.0",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lm2594n-5-0.kicad_sym",+ "lm2594n-5-0.kicad_mod",+ "lm2594n-5-0.glb",+ "lm2594n-5-0.step",+ "lm2594n-5-0.lbr",+ "docs/hero.png",+ "docs/lm2594n-5-0-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "lm2594n-5-0-hero.glb",+ "lm2594n-5-0-hero.overlay.json"+ ],+ "component": {+ "mpn": "LM2594N-5.0",+ "manufacturer": "Texas Instruments",+ "package": "PDIP-8",+ "pin_count": 8,+ "category": "Power Management (PMIC)",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/lm2594",+ "parts": {+ "symbol": "lm2594n-5-0.kicad_sym",+ "footprint": "lm2594n-5-0.kicad_mod",+ "model_3d": "lm2594n-5-0-hero.glb",+ "model_3d_plain": "lm2594n-5-0.glb",+ "model_3d_step": "lm2594n-5-0-etched.step",+ "model_3d_step_plain": "lm2594n-5-0.step",+ "lbr": "lm2594n-5-0.lbr"+ },+ "distributor_links": {+ "lcsc": "C1355298",+ "digikey": "LM2594N-5.0-ND",+ "mouser": "926-LM2594N-50"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T05:01:44Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": "LM2594N-5.0-ND",+ "status": "found",+ "lifecycle": "Obsolete"+ },+ "mouser": {+ "pn": "926-LM2594N-50",+ "status": "found",+ "lifecycle": "Obsolete"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "NC",+ "type": "unconnected",+ "description": "No connection; the datasheet notes NC pins are not internally connected but must be soldered to the PCB for best heat transfer."+ },+ {+ "number": "2",+ "name": "NC",+ "type": "unconnected",+ "description": "No connection; the datasheet notes NC pins are not internally connected but must be soldered to the PCB for best heat transfer."+ },+ {+ "number": "3",+ "name": "NC",+ "type": "unconnected",+ "description": "No connection; the datasheet notes NC pins are not internally connected but must be soldered to the PCB for best heat transfer."+ },+ {+ "number": "4",+ "name": "Feedback",+ "type": "input",+ "description": "Senses the regulated output voltage to complete the feedback loop."+ },+ {+ "number": "5",+ "name": "ON/OFF",+ "type": "input",+ "description": "Logic-level shutdown: pulling below about 1.3 V turns the regulator on and pulling above 1.3 V (up to a maximum of 25 V) shuts it down, reducing total input supply current to about 80 µA; leave open or tie to ground to keep the regulator always on."+ },+ {+ "number": "6",+ "name": "Ground",+ "type": "power_in",+ "description": "Circuit ground."+ },+ {+ "number": "7",+ "name": "+VIN",+ "type": "power_in",+ "description": "Positive input supply for the switching regulator, requiring a suitable input bypass capacitor at this pin; recommended operating supply is 4.5 V to 40 V for LM2594 (60 V for LM2594HV) with absolute maximum of 45 V for LM2594."+ },+ {+ "number": "8",+ "name": "Output",+ "type": "output",+ "description": "Internal switch output that swings between (+VIN − VSAT) and approximately −0.5 V with duty cycle VOUT/VIN; keep the PCB copper area on this pin to a minimum to limit coupling to sensitive circuitry."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Pinout is taken from the shared D/P package table for the LM2594/LM2594HV family (Figure 6-1 and Tab; The datasheet's electrical limits for pins 5 and 7 (ON/OFF up to 25 V, +VIN 4.5 V to 40 V recommende",+ "1/8 pin names appear NOWHERE in the datasheet text: ['6:Ground@p3']"+ ],+ "pages_sent": 10,+ "cost_usd": 0.0631,+ "at": "2026-10-08T05:01:28"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/lm2594",+ "pages": 48,+ "sha256": "f4ff0460f0a09cf3",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 8,+ "described": 8,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lm2594n-5-0.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "body on z = 0, through-hole leads below",+ "extents_mm": [+ 7.874,+ 9.27,+ 6.98+ ],+ "zmin_mm": -3.3,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "4a377a56a8d9e9c0b86c095ef9ecc1869ac19e7f5069a3247b294250bf4f235d",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lm2594n-5-0-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "body on z = 0, through-hole leads below",+ "extents_mm": [+ 7.874,+ 9.27,+ 6.98+ ],+ "zmin_mm": -3.3,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "9ef016a35f6a03ea2de0b0f24084c3dd9c933288fefb77cf90468b397049e1b7",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}