← Commit history

Initial commit: component/lm25088mhx-1

Ray ·b092bc65ca ·
2 files changed +249
README.mdadded+54
@@ -0,0 +1,54 @@+# LM25088MHX-1++**Texas Instruments** · DC-DC Controllers · HTSSOP-16-EP++LM25088MHX-1 from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN | power_in | Input supply voltage; IC operating range 4.5 V to 42 V. |+| 2 | EN | input | Enable input; below 0.4 V is shutdown mode, 0.4 V to 1.2 V is standby mode, above 1.2 V is operational. |+| 3 | SS | input | Soft-start input; internal 11-µA current source charges external capacitor to control startup ramp. |+| 4 | RAMP | output | Ramp signal output; external capacitor between this pin and GND sets emulated current mode control slope. |+| 5 | RT/SYNC | input | Oscillator frequency setting input (single resistor to GND sets 50 kHz to 1 MHz) and external synchronization input. |+| 6 | GND | power_in | Ground return. |+| 7 | COMP | output | Error amplifier output; loop compensation network connected between this pin and FB pin. |+| 8 | FB | input | Feedback input; connected to error amplifier inverting input with 1.205 V regulation threshold. |+| 9 | OUT | input | Output voltage sense input; connect directly to regulated converter output. |+| 10 | DITH | output | Frequency dithering output (LM25088-1 only); capacitor to GND modulates oscillator frequency ±5% from nominal set by RT resistor. |+| 11 | CSG | power_in | Current sense ground; low-side reference for external current sense resistor. |+| 12 | CS | input | Current sense input; measures re-circulating diode current for emulated ramp DC offset level. |+| 13 | SW | output | Switching node output; connected to source terminal of external high-side MOSFET switch. |+| 14 | HG | output | High-side gate driver output; connected to gate terminal of external MOSFET. |+| 15 | BOOT | power_out | Bootstrap capacitor connection; external capacitor between BOOT and SW pins charged from VCC to bias gate driver. |+| 16 | VCC | power_out | Bias regulator output; regulated to 7.8 V typical, requires 0.1 µF to 10 µF ceramic decoupling capacitor. |+| 17 | EP | passive | Exposed pad; electrically isolated, must be soldered to ground plane to reduce thermal resistance. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Power Supply Chip |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `LM25088MHX-1`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `lm25088mhx-1-etched.step` / `lm25088mhx-1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm25088mhx-1.step` / `lm25088mhx-1.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm25088-q1) (41 pp, sha256 `9f08ba8be5b0d3b1`, retrieved 2026-09-18, tier: lcsc)+- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm25088mhx-1-datasheet.pdf)
page.jsonadded+195
@@ -0,0 +1,195 @@+{+  "slug": "lm25088mhx-1",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments DC-DC Controllers, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "power supply chip",+    "lm25088mhx-1",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lm25088mhx-1.kicad_sym",+    "lm25088mhx-1.kicad_mod",+    "lm25088mhx-1.glb",+    "lm25088mhx-1.step",+    "lm25088mhx-1.lbr",+    "docs/hero.png",+    "docs/lm25088mhx-1-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LM25088MHX-1",+    "manufacturer": "Texas Instruments",+    "package": "HTSSOP-16-EP",+    "pin_count": 17,+    "category": "Power Supply Chip",+    "subcategory": "DC-DC Controllers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/lm25088-q1",+    "parts": {+      "symbol": "lm25088mhx-1.kicad_sym",+      "footprint": "lm25088mhx-1.kicad_mod",+      "model_3d": "lm25088mhx-1-etched.glb",+      "model_3d_plain": "lm25088mhx-1.glb",+      "model_3d_step": "lm25088mhx-1-etched.step",+      "model_3d_step_plain": "lm25088mhx-1.step",+      "lbr": "lm25088mhx-1.lbr"+    },+    "distributor_links": {+      "lcsc": "C2658387"+    },+    "pins": [+      {+        "number": "1",+        "name": "VIN",+        "type": "power_in",+        "description": "Input supply voltage; IC operating range 4.5 V to 42 V."+      },+      {+        "number": "2",+        "name": "EN",+        "type": "input",+        "description": "Enable input; below 0.4 V is shutdown mode, 0.4 V to 1.2 V is standby mode, above 1.2 V is operational."+      },+      {+        "number": "3",+        "name": "SS",+        "type": "input",+        "description": "Soft-start input; internal 11-µA current source charges external capacitor to control startup ramp."+      },+      {+        "number": "4",+        "name": "RAMP",+        "type": "output",+        "description": "Ramp signal output; external capacitor between this pin and GND sets emulated current mode control slope."+      },+      {+        "number": "5",+        "name": "RT/SYNC",+        "type": "input",+        "description": "Oscillator frequency setting input (single resistor to GND sets 50 kHz to 1 MHz) and external synchronization input."+      },+      {+        "number": "6",+        "name": "GND",+        "type": "power_in",+        "description": "Ground return."+      },+      {+        "number": "7",+        "name": "COMP",+        "type": "output",+        "description": "Error amplifier output; loop compensation network connected between this pin and FB pin."+      },+      {+        "number": "8",+        "name": "FB",+        "type": "input",+        "description": "Feedback input; connected to error amplifier inverting input with 1.205 V regulation threshold."+      },+      {+        "number": "9",+        "name": "OUT",+        "type": "input",+        "description": "Output voltage sense input; connect directly to regulated converter output."+      },+      {+        "number": "10",+        "name": "DITH",+        "type": "output",+        "description": "Frequency dithering output (LM25088-1 only); capacitor to GND modulates oscillator frequency ±5% from nominal set by RT resistor."+      },+      {+        "number": "11",+        "name": "CSG",+        "type": "power_in",+        "description": "Current sense ground; low-side reference for external current sense resistor."+      },+      {+        "number": "12",+        "name": "CS",+        "type": "input",+        "description": "Current sense input; measures re-circulating diode current for emulated ramp DC offset level."+      },+      {+        "number": "13",+        "name": "SW",+        "type": "output",+        "description": "Switching node output; connected to source terminal of external high-side MOSFET switch."+      },+      {+        "number": "14",+        "name": "HG",+        "type": "output",+        "description": "High-side gate driver output; connected to gate terminal of external MOSFET."+      },+      {+        "number": "15",+        "name": "BOOT",+        "type": "power_out",+        "description": "Bootstrap capacitor connection; external capacitor between BOOT and SW pins charged from VCC to bias gate driver."+      },+      {+        "number": "16",+        "name": "VCC",+        "type": "power_out",+        "description": "Bias regulator output; regulated to 7.8 V typical, requires 0.1 µF to 10 µF ceramic decoupling capacitor."+      },+      {+        "number": "17",+        "name": "EP",+        "type": "passive",+        "description": "Exposed pad; electrically isolated, must be soldered to ground plane to reduce thermal resistance."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 41,+        "cost_usd": 0.457,+        "at": "2026-09-18T06:29:02"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/lm25088-q1",+        "pages": 41,+        "sha256": "9f08ba8be5b0d3b1",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 17,+        "described": 17,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file