component
LM25085ASD
Public Made by Adomby adom
Texas Instruments DC-DC Controllers, WSON-8-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+45@@ -0,0 +1,45 @@+# LM25085ASD++**Texas Instruments** · DC-DC Controllers · WSON-8-EP(3x3)++LM25085ASD from Texas Instruments, in a WSON-8-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | ADJ | passive | Current limit adjust: the current limit threshold is set by an external resistor from VIN to ADJ, together with the external sense resistor or the PFET RDS(ON), and the ADJ pin carries an internal 40 µA current sink with a recommended CADJ of 1000 pF. |+| 2 | RT | input | On-time control and shutdown: an external resistor from VIN to RT sets the buck switch on-time and switching frequency, and grounding this pin shuts down the controller. |+| 3 | FB | input | Voltage feedback from the regulated output to the regulation and over-voltage comparators, with the regulation level at 0.9V. |+| 4 | GND | power_in | Circuit ground, the reference for all internal circuitry. |+| 5 | ISEN | input | Current sense input for current limit detection: connect to the PFET drain when using RDS(ON) sensing, or to the PFET source and sense resistor when using a sense resistor, with Kelvin connections required for accuracy. |+| 6 | PGATE | output | Gate driver output that connects to the gate of the external PFET, swinging between VIN (Q1 off) and the VCC pin voltage (Q1 on). |+| 7 | VCC | power_out | Output of the gate driver bias regulator, regulated approximately 7.7V below VIN with at least 20 mA capability, requiring a low ESR capacitor (0.47 µF) placed close to VIN and VCC. |+| 8 | VIN | power_in | Input supply voltage with an operating range of 4.5V to 42V, requiring a low ESR bypass capacitor located as close as possible to the VIN and GND pins. |+| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | WSON-8-EP(3x3) |+| Category | Power Supply Chip |+| Pins | 9 |++## CAD (KiCad official)++- Symbol: `LM25085ASD`+- Footprint: `Package_SON:WSON-8-1EP_3x3mm_P0.5mm_EP1.6x2.0mm`+- 3D model: WSON-8-EP(3x3) (KiCad packages3D, STEP)+- 3D model files: `lm25085asd-etched.step` / `lm25085asd-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm25085asd.step` / `lm25085asd.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm25085a) (36 pp, sha256 `941a26173c0d4ed5`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm25085asd-datasheet.pdf)
page.jsonadded+205@@ -0,0 +1,205 @@+{+ "slug": "lm25085asd",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Controllers, WSON-8-EP(3x3). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "lm25085asd",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lm25085asd.kicad_sym",+ "lm25085asd.kicad_mod",+ "lm25085asd.glb",+ "lm25085asd.step",+ "lm25085asd.lbr",+ "docs/hero.png",+ "docs/lm25085asd-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "lm25085asd-hero.glb",+ "lm25085asd-hero.overlay.json"+ ],+ "component": {+ "mpn": "LM25085ASD",+ "manufacturer": "Texas Instruments",+ "package": "WSON-8-EP(3x3)",+ "pin_count": 9,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Controllers",+ "datasheet": "https://www.ti.com/cn/lit/gpn/lm25085a",+ "parts": {+ "symbol": "lm25085asd.kicad_sym",+ "footprint": "lm25085asd.kicad_mod",+ "model_3d": "lm25085asd-hero.glb",+ "model_3d_plain": "lm25085asd.glb",+ "model_3d_step": "lm25085asd-etched.step",+ "model_3d_step_plain": "lm25085asd.step",+ "lbr": "lm25085asd.lbr"+ },+ "distributor_links": {+ "lcsc": "C1848486"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T16:44:35Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": null,+ "status": "no match"+ },+ "mouser": {+ "pn": null,+ "status": "no match"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "ADJ",+ "type": "passive",+ "description": "Current limit adjust: the current limit threshold is set by an external resistor from VIN to ADJ, together with the external sense resistor or the PFET RDS(ON), and the ADJ pin carries an internal 40 µA current sink with a recommended CADJ of 1000 pF."+ },+ {+ "number": "2",+ "name": "RT",+ "type": "input",+ "description": "On-time control and shutdown: an external resistor from VIN to RT sets the buck switch on-time and switching frequency, and grounding this pin shuts down the controller."+ },+ {+ "number": "3",+ "name": "FB",+ "type": "input",+ "description": "Voltage feedback from the regulated output to the regulation and over-voltage comparators, with the regulation level at 0.9V."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Circuit ground, the reference for all internal circuitry."+ },+ {+ "number": "5",+ "name": "ISEN",+ "type": "input",+ "description": "Current sense input for current limit detection: connect to the PFET drain when using RDS(ON) sensing, or to the PFET source and sense resistor when using a sense resistor, with Kelvin connections required for accuracy."+ },+ {+ "number": "6",+ "name": "PGATE",+ "type": "output",+ "description": "Gate driver output that connects to the gate of the external PFET, swinging between VIN (Q1 off) and the VCC pin voltage (Q1 on)."+ },+ {+ "number": "7",+ "name": "VCC",+ "type": "power_out",+ "description": "Output of the gate driver bias regulator, regulated approximately 7.7V below VIN with at least 20 mA capability, requiring a low ESR capacitor (0.47 µF) placed close to VIN and VCC."+ },+ {+ "number": "8",+ "name": "VIN",+ "type": "power_in",+ "description": "Input supply voltage with an operating range of 4.5V to 42V, requiring a low ESR bypass capacitor located as close as possible to the VIN and GND pins."+ },+ {+ "number": "9",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: The WSON pin-to-position layout in Figure 3 (page 2) is garbled in the text extraction, so the physi; The datasheet gives no WSON-specific electrical or pin table beyond the shared pin description table; Page 23 (package addendum) confirms that LM25085ASD is orderable in the WSON (NGQ), 8-pin package, m",+ "exposed pad 9 added from the footprint",+ "dropped thermal pad ['EP'] absent from footprint"+ ],+ "pages_sent": 11,+ "cost_usd": 0.0695,+ "at": "2026-10-08T16:44:22"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/lm25085a",+ "pages": 36,+ "sha256": "941a26173c0d4ed5",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 9,+ "described": 9,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lm25085asd.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.98,+ 0.82+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "cbee016fb8ee69c44b13d8818fcf65dcf240f5fdca70b22700521eb617c5311a",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lm25085asd-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 3,+ 2.98,+ 0.82+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "5a7bce07e7b4ec05b1a1cccdb178ee8fb5a8f3f7b38709987da1d5292a351a11",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}