component
LM20125MHX
Public Made by Adomby adom
Texas Instruments DC-DC Converters, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
← Commit history
README.mdadded+53@@ -0,0 +1,53 @@+# LM20125MHX++**Texas Instruments** · DC-DC Converters · HTSSOP-16-EP++LM20125MHX from Texas Instruments, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | SS/TRK | input | Soft-start or tracking control input charged by an internal 5 µA source; if driven externally below 800 mV it overrides the internal reference, and if left open an internal 1 ms soft-start ramp is used. |+| 2 | FB | input | Feedback input to the inverting input of the internal transconductance error amplifier, which regulates against the internal 800 mV reference. |+| 3 | PGOOD | output | Open-drain power-good output that indicates the output is regulating within tolerance and requires a 10 kΩ to 100 kΩ pull-up resistor for most applications. |+| 4 | COMP | passive | External compensation pin where a resistor and capacitor are connected to compensate the device. |+| 5 | NC | unconnected | Not internally connected; the datasheet states this pin must be connected to GND to ensure proper operation. |+| 6 | PVIN | power_in | Input voltage to the internal power switches, specified for 2.95 V to 5.5 V; tie PVIN pins 6 and 7 together at the device with a low-ESR capacitor placed nearby. |+| 7 | PVIN | power_in | Input voltage to the internal power switches, specified for 2.95 V to 5.5 V; tie PVIN pins 6 and 7 together at the device with a low-ESR capacitor placed nearby. |+| 8 | SW | output | PWM switch output of the internal power switches; pins 8 and 9 are tied together. |+| 9 | SW | output | PWM switch output of the internal power switches; pins 8 and 9 are tied together. |+| 10 | PGND | power_in | Power ground for the internal power switches. |+| 11 | PGND | power_in | Power ground for the internal power switches. |+| 12 | EN | input | Precision enable input with hysteresis; an external divider sets the turn-on threshold, and it should be tied to PVIN if not used. |+| 13 | VCC | power_out | Output of the internal 2.7 V sub-regulator, which must be bypassed with a 1 µF ceramic capacitor. |+| 14 | AVIN | power_in | Analog supply that generates the internal bias and must be connected to VIN through a low-pass RC filter. |+| 15 | AGND | power_in | Quiet analog ground for the internal bias circuitry. |+| 16 | NC | unconnected | Not internally connected; the datasheet states this pin must be connected to GND to ensure proper operation. |+| 17 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | HTSSOP-16-EP |+| Category | Power Supply Chip |+| Pins | 17 |++## CAD (KiCad official)++- Symbol: `LM20125MHX`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)+- 3D model files: `lm20125mhx-etched.step` / `lm20125mhx-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lm20125mhx.step` / `lm20125mhx.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/lm20125) (32 pp, sha256 `bd9ed15653c896bc`, retrieved 2026-10-08, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lm20125mhx-datasheet.pdf)
page.jsonadded+253@@ -0,0 +1,253 @@+{+ "slug": "lm20125mhx",+ "version": "0.1.0",+ "type": "component",+ "description": "Texas Instruments DC-DC Converters, HTSSOP-16-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "power supply chip",+ "lm20125mhx",+ "factory-2.0.0",+ "extractor-text"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lm20125mhx.kicad_sym",+ "lm20125mhx.kicad_mod",+ "lm20125mhx.glb",+ "lm20125mhx.step",+ "lm20125mhx.lbr",+ "docs/hero.png",+ "docs/lm20125mhx-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html",+ "lm20125mhx-hero.glb",+ "lm20125mhx-hero.overlay.json"+ ],+ "component": {+ "mpn": "LM20125MHX",+ "manufacturer": "Texas Instruments",+ "package": "HTSSOP-16-EP",+ "pin_count": 17,+ "category": "Power Supply Chip",+ "subcategory": "DC-DC Converters",+ "datasheet": "https://www.ti.com/cn/lit/gpn/lm20125",+ "parts": {+ "symbol": "lm20125mhx.kicad_sym",+ "footprint": "lm20125mhx.kicad_mod",+ "model_3d": "lm20125mhx-hero.glb",+ "model_3d_plain": "lm20125mhx.glb",+ "model_3d_step": "lm20125mhx-etched.step",+ "model_3d_step_plain": "lm20125mhx.step",+ "lbr": "lm20125mhx.lbr"+ },+ "distributor_links": {+ "lcsc": "C2070647"+ },+ "distributor_check": {+ "checked_at": "2026-10-08T19:21:33Z",+ "source": "Component Ocean /api/assign-pns",+ "digikey": {+ "pn": null,+ "status": "no match"+ },+ "mouser": {+ "pn": null,+ "status": "no match"+ }+ },+ "pins": [+ {+ "number": "1",+ "name": "SS/TRK",+ "type": "input",+ "description": "Soft-start or tracking control input charged by an internal 5 µA source; if driven externally below 800 mV it overrides the internal reference, and if left open an internal 1 ms soft-start ramp is used."+ },+ {+ "number": "2",+ "name": "FB",+ "type": "input",+ "description": "Feedback input to the inverting input of the internal transconductance error amplifier, which regulates against the internal 800 mV reference."+ },+ {+ "number": "3",+ "name": "PGOOD",+ "type": "output",+ "description": "Open-drain power-good output that indicates the output is regulating within tolerance and requires a 10 kΩ to 100 kΩ pull-up resistor for most applications."+ },+ {+ "number": "4",+ "name": "COMP",+ "type": "passive",+ "description": "External compensation pin where a resistor and capacitor are connected to compensate the device."+ },+ {+ "number": "5",+ "name": "NC",+ "type": "unconnected",+ "description": "Not internally connected; the datasheet states this pin must be connected to GND to ensure proper operation."+ },+ {+ "number": "6",+ "name": "PVIN",+ "type": "power_in",+ "description": "Input voltage to the internal power switches, specified for 2.95 V to 5.5 V; tie PVIN pins 6 and 7 together at the device with a low-ESR capacitor placed nearby."+ },+ {+ "number": "7",+ "name": "PVIN",+ "type": "power_in",+ "description": "Input voltage to the internal power switches, specified for 2.95 V to 5.5 V; tie PVIN pins 6 and 7 together at the device with a low-ESR capacitor placed nearby."+ },+ {+ "number": "8",+ "name": "SW",+ "type": "output",+ "description": "PWM switch output of the internal power switches; pins 8 and 9 are tied together."+ },+ {+ "number": "9",+ "name": "SW",+ "type": "output",+ "description": "PWM switch output of the internal power switches; pins 8 and 9 are tied together."+ },+ {+ "number": "10",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground for the internal power switches."+ },+ {+ "number": "11",+ "name": "PGND",+ "type": "power_in",+ "description": "Power ground for the internal power switches."+ },+ {+ "number": "12",+ "name": "EN",+ "type": "input",+ "description": "Precision enable input with hysteresis; an external divider sets the turn-on threshold, and it should be tied to PVIN if not used."+ },+ {+ "number": "13",+ "name": "VCC",+ "type": "power_out",+ "description": "Output of the internal 2.7 V sub-regulator, which must be bypassed with a 1 µF ceramic capacitor."+ },+ {+ "number": "14",+ "name": "AVIN",+ "type": "power_in",+ "description": "Analog supply that generates the internal bias and must be connected to VIN through a low-pass RC filter."+ },+ {+ "number": "15",+ "name": "AGND",+ "type": "power_in",+ "description": "Quiet analog ground for the internal bias circuitry."+ },+ {+ "number": "16",+ "name": "NC",+ "type": "unconnected",+ "description": "Not internally connected; the datasheet states this pin must be connected to GND to ensure proper operation."+ },+ {+ "number": "17",+ "name": "EP",+ "type": "passive",+ "description": "Exposed pad (from the footprint; not named in the datasheet pin table)."+ }+ ],+ "provenance": {+ "extractor": "extract_pins 0.3",+ "factory_chain": {+ "factory": "2.0.0",+ "extractor": "extract_pins 0.3",+ "primary_model": "claude-haiku-5-5",+ "primary_mode": "text",+ "consensus_model": "claude-sonnet-5-5",+ "consensus": "agreed",+ "guards": "pin_guards 0.1: passed",+ "guard_notes": [+ "extractor flagged: Datasheet says NC pins must be connected to GND for proper operation, but they are typed 'unconnecte; The Connection Diagram text extracted from the PDF is garbled, so pin numbers come from the Pin Desc; PGOOD is an open-drain output; KiCad's open_collector is not in the allowed type list, so it is type",+ "exposed pad 17 added from the footprint",+ "dropped thermal pad ['EP'] absent from footprint"+ ],+ "pages_sent": 6,+ "cost_usd": 0.0498,+ "at": "2026-10-08T19:20:45"+ },+ "datasheet": {+ "url": "https://www.ti.com/cn/lit/gpn/lm20125",+ "pages": 32,+ "sha256": "bd9ed15653c896bc",+ "source_tier": "lcsc"+ },+ "cad": "KiCad official (CC-BY-SA 4.0)",+ "pins": {+ "total": 17,+ "described": 17,+ "cites_pages": true,+ "refuses_to_fabricate": true+ }+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ },+ "models_3d": [+ {+ "file": "lm20125mhx.step",+ "role": "plain",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "7982746831c0bd23f4690608869ad67776faae5c762fb0376666126a3998921b",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ },+ {+ "file": "lm20125mhx-etched.step",+ "role": "eda",+ "up": "Z",+ "units": "mm",+ "origin": "footprint origin = pad-pattern centre",+ "seat": "z = 0",+ "extents_mm": [+ 6.4,+ 5,+ 1.1+ ],+ "zmin_mm": 0,+ "centre_offset_mm": 0,+ "footprint_binding": "identity",+ "sha256": "72c429511c151b819f3fcadbb8fec2cfefe58f02c67678ff109d2a80790f1682",+ "checked": "2026-10-08",+ "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+ }+ ]+ },+ "visibility": "public",+ "org": "adom",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}