← Commit history

Initial commit: component/lis3dshtr

Ray ·ba1d6b4f45 ·
2 files changed +244
README.mdadded+52
@@ -0,0 +1,52 @@+# LIS3DSHTR++**STMicroelectronics** · Accelerometers · LGA-16(3x3)++LIS3DSHTR from STMicroelectronics, in a LGA-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | Vdd_IO | power_in | Power supply for I/O pins, 1.71 to (Vdd+0.1) V independent of core supply |+| 2 | NC | unconnected | Not connected |+| 3 | NC | unconnected | Not connected |+| 4 | SCL/SPC | input | Serial clock input for I2C (up to 400 kHz fast mode) or SPI (up to 10 MHz) depending on interface mode |+| 5 | GND | power_in | Ground supply (0 V reference) |+| 6 | SDA/SDI/SDO | bidirectional | I2C serial data (open-drain), SPI serial data input, or 3-wire interface serial data output depending on mode selection |+| 7 | SEL/SDO | bidirectional | I2C address selection input (strapped to Vdd or GND) or SPI serial data output depending on mode |+| 8 | CS | input | SPI chip select enable and I2C/SPI mode selection (high = I2C, low = SPI) |+| 9 | INT 2 | output | Interrupt 2 output, configurable for active high/low and pulse/latch trigger modes via CTRL_REG3 |+| 10 | Reserved | unconnected | Reserved pin, must connect to GND for proper device operation |+| 11 | INT 1/DRDY | output | Interrupt 1 or data ready output, configurable to route state machine interrupt or data ready signal via CTRL_REG3 |+| 12 | GND | power_in | Ground supply (0 V reference) |+| 13 | GND | power_in | Ground supply (0 V reference) |+| 14 | Vdd | power_in | Core power supply, 1.71 to 3.6 V range (factory calibrated at 2.5 V) |+| 15 | Reserved | unconnected | Reserved pin, must connect to Vdd for proper device operation |+| 16 | GND | power_in | Ground supply (0 V reference) |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | LGA-16(3x3) |+| Category | Sensors |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `LIS3DSHTR`+- Footprint: `Package_LGA:LGA-16_3x3mm_P0.5mm`+- 3D model: LGA-16(3x3) (KiCad packages3D, STEP)+- 3D model files: `lis3dshtr-etched.step` / `lis3dshtr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lis3dshtr.step` / `lis3dshtr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588893262258319360) (53 pp, sha256 `9f710e10eef37137`, retrieved 2026-09-29, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lis3dshtr-datasheet.pdf)
page.jsonadded+192
@@ -0,0 +1,192 @@+{+  "slug": "lis3dshtr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics Accelerometers, LGA-16(3x3). Pinout reviewed by a person against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "sensors",+    "lis3dshtr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "lis3dshtr.kicad_sym",+    "lis3dshtr.kicad_mod",+    "lis3dshtr.glb",+    "lis3dshtr.step",+    "lis3dshtr.lbr",+    "docs/hero.png",+    "docs/lis3dshtr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "LIS3DSHTR",+    "manufacturer": "STMicroelectronics",+    "package": "LGA-16(3x3)",+    "pin_count": 16,+    "category": "Sensors",+    "subcategory": "Accelerometers",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588893262258319360",+    "parts": {+      "symbol": "lis3dshtr.kicad_sym",+      "footprint": "lis3dshtr.kicad_mod",+      "model_3d": "lis3dshtr-etched.glb",+      "model_3d_plain": "lis3dshtr.glb",+      "model_3d_step": "lis3dshtr-etched.step",+      "model_3d_step_plain": "lis3dshtr.step",+      "lbr": "lis3dshtr.lbr"+    },+    "distributor_links": {+      "lcsc": "C1884688",+      "digikey": "497-13244-2-ND",+      "mouser": "511-LIS3DSHTR"+    },+    "distributor_check": {+      "checked_at": "2026-09-29T16:39:59Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "497-13244-2-ND",+        "status": "found",+        "lifecycle": "Obsolete"+      },+      "mouser": {+        "pn": "511-LIS3DSHTR",+        "status": "found",+        "lifecycle": "Obsolete"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "Vdd_IO",+        "type": "power_in",+        "description": "Power supply for I/O pins, 1.71 to (Vdd+0.1) V independent of core supply"+      },+      {+        "number": "2",+        "name": "NC",+        "type": "unconnected",+        "description": "Not connected"+      },+      {+        "number": "3",+        "name": "NC",+        "type": "unconnected",+        "description": "Not connected"+      },+      {+        "number": "4",+        "name": "SCL/SPC",+        "type": "input",+        "description": "Serial clock input for I2C (up to 400 kHz fast mode) or SPI (up to 10 MHz) depending on interface mode"+      },+      {+        "number": "5",+        "name": "GND",+        "type": "power_in",+        "description": "Ground supply (0 V reference)"+      },+      {+        "number": "6",+        "name": "SDA/SDI/SDO",+        "type": "bidirectional",+        "description": "I2C serial data (open-drain), SPI serial data input, or 3-wire interface serial data output depending on mode selection"+      },+      {+        "number": "7",+        "name": "SEL/SDO",+        "type": "bidirectional",+        "description": "I2C address selection input (strapped to Vdd or GND) or SPI serial data output depending on mode"+      },+      {+        "number": "8",+        "name": "CS",+        "type": "input",+        "description": "SPI chip select enable and I2C/SPI mode selection (high = I2C, low = SPI)"+      },+      {+        "number": "9",+        "name": "INT 2",+        "type": "output",+        "description": "Interrupt 2 output, configurable for active high/low and pulse/latch trigger modes via CTRL_REG3"+      },+      {+        "number": "10",+        "name": "Reserved",+        "type": "unconnected",+        "description": "Reserved pin, must connect to GND for proper device operation"+      },+      {+        "number": "11",+        "name": "INT 1/DRDY",+        "type": "output",+        "description": "Interrupt 1 or data ready output, configurable to route state machine interrupt or data ready signal via CTRL_REG3"+      },+      {+        "number": "12",+        "name": "GND",+        "type": "power_in",+        "description": "Ground supply (0 V reference)"+      },+      {+        "number": "13",+        "name": "GND",+        "type": "power_in",+        "description": "Ground supply (0 V reference)"+      },+      {+        "number": "14",+        "name": "Vdd",+        "type": "power_in",+        "description": "Core power supply, 1.71 to 3.6 V range (factory calibrated at 2.5 V)"+      },+      {+        "number": "15",+        "name": "Reserved",+        "type": "unconnected",+        "description": "Reserved pin, must connect to Vdd for proper device operation"+      },+      {+        "number": "16",+        "name": "GND",+        "type": "power_in",+        "description": "Ground supply (0 V reference)"+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588893262258319360",+        "pages": 53,+        "sha256": "9f710e10eef37137",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file