← Commit history
lgs6305: factory component page (tier=lcsc)
3 files changed
+22−19
README.md+6−6@@ -8,12 +8,12 @@ LGS6305 from Legend Si, in a SOT-23-6. Pinout and pin descriptions extracted fro | Pin | Name | Type | Function | |---|---|---|---|-| 1 | SW | output | Internal power-switch node. Connects to the external buck inductor and Schottky freewheeling diode. Carries the switched output current (up to ~460mA peak current limit) at up to 60V. |-| 2 | GND | power_in | Ground reference pin for the device. All voltages are referenced to this pin. |-| 3 | VCC | power_out | Internal LDO regulated output, fixed 5V (4.8-5.2V), rated 7mA (8mA short-circuit current limit). Requires a 1uF-4.7uF ceramic decoupling capacitor to GND placed close to the pin. Powers the internal control circuitry and MOSFET driver; may also power a small external load. |-| 4 | EN | input | Enable / PWM dimming input. Chip enables when the pin rises above V_EN_H (1.4V typ) and disables (low-power sleep) when it falls below V_EN_L (0.6V typ). Accepts PWM dimming from 100Hz up to 10kHz (I_OUT scales linearly with duty cycle). Has an internal 800kΩ pull-down; low-voltage pin - can be tied directly to VCC for always-on operation. Absolute max 6V referenced to GND. |-| 5 | VIN | power_in | Main input supply pin, 12V-60V recommended (survives 80V transients). Also serves as the top-of-sense-resistor connection for LED current sensing (R_SENSE is placed between VIN and CSN). Requires a 4.7uF X5R/X7R ceramic bypass capacitor to GND placed close to the pin. Absolute max 60V referenced to GND. |-| 6 | CSN | input | LED current-sense input. Connects to the bottom of the external current-sense resistor R_SENSE (top is at VIN). Regulates so that V_VIN − V_CSN = 0.18V typical, giving I_OUT = 0.18V/R_SENSE. CSN bias current 12uA typical. High-impedance node - keep trace short and away from the SW node. Absolute max range VIN−6V to VIN+0.3V. |+| 1 | SW | output | Internal power switch node. Connects externally to the power inductor and the Schottky freewheeling diode (e.g. SS16). Absolute max VSW to GND: -0.3V to +60V. Peak current limit ILIMIT.SW(Peak) ≈ 460mA. |+| 2 | GND | power_in | Device ground / return pin. |+| 3 | VCC | power_out | 5V LDO regulated output pin, rated 7mA (typical), with ~8mA short-circuit current limit. A 1uF-4.7uF ceramic decoupling capacitor must be placed between VCC and GND as close to the pin as possible. Can be used as a supply for external control circuitry. |+| 4 | EN | input | Enable / dimming input. Accepts a PWM dimming signal up to 10kHz. VEN_H ≥ 1.4V (enable), VEN_L ≤ 0.6V (disable). Absolute max to GND: -0.3V to +6V. Tie to VCC for always-on operation. |+| 5 | VIN | power_in | Input supply / current-sense high side. Connects to the LED current-sense resistor RSence (other side goes to CSN). Recommended operating range 12V-60V, absolute max -0.3V to +60V (transient up to 80V). |+| 6 | CSN | input | LED current-sense negative input. Connects to the low side of the external current-sense resistor RSence. Regulated VIN−VCSN ≈ 0.18V; output current IOUT = 0.18V / RSence. CSN bias current ~12uA. Absolute max: (VIN−6V) to (VIN+0.3V). | ## Key specifications
lgs6305.lbr+9−3@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>Legend Si LED Drivers, SOT-23-6</description> <packages> <package name="SOT-23-6"> <description>6 pads, 3.6 x 2.5 mm. SOT, 6 Pin</description>@@ -84,6 +84,7 @@ </packages> <symbols> <symbol name="LGS6305">+ <description>Legend Si LED Drivers, SOT-23-6</description> <wire x1="-12.7" y1="5.08" x2="12.7" y2="5.08" width="0.254" layer="94"/> <wire x1="12.7" y1="5.08" x2="12.7" y2="-5.08" width="0.254" layer="94"/> <wire x1="12.7" y1="-5.08" x2="-12.7" y2="-5.08" width="0.254" layer="94"/>@@ -100,7 +101,7 @@ </symbols> <devicesets> <deviceset name="LGS6305" prefix="U">- <description></description>+ <description>Legend Si LED Drivers, SOT-23-6</description> <gates> <gate name="G$1" symbol="LGS6305" x="0" y="0"/> </gates>@@ -114,7 +115,12 @@ <connect gate="G$1" pin="VIN" pad="5"/> <connect gate="G$1" pin="EN" pad="4"/> </connects>- <technologies><technology name=""/></technologies>+ <technologies>+ <technology name="">+ <attribute name="MPN" value="LGS6305" constant="no"/>+ <attribute name="MANUFACTURER" value="Legend Si" constant="no"/>+ </technology>+ </technologies> </device> </devices> </deviceset>
page.json+7−10@@ -32,37 +32,37 @@ "number": "1", "name": "SW", "type": "output",- "description": "Internal power-switch node. Connects to the external buck inductor and Schottky freewheeling diode. Carries the switched output current (up to ~460mA peak current limit) at up to 60V."+ "description": "Internal power switch node. Connects externally to the power inductor and the Schottky freewheeling diode (e.g. SS16). Absolute max VSW to GND: -0.3V to +60V. Peak current limit ILIMIT.SW(Peak) \u2248 460mA." }, { "number": "2", "name": "GND", "type": "power_in",- "description": "Ground reference pin for the device. All voltages are referenced to this pin."+ "description": "Device ground / return pin." }, { "number": "3", "name": "VCC", "type": "power_out",- "description": "Internal LDO regulated output, fixed 5V (4.8-5.2V), rated 7mA (8mA short-circuit current limit). Requires a 1uF-4.7uF ceramic decoupling capacitor to GND placed close to the pin. Powers the internal control circuitry and MOSFET driver; may also power a small external load."+ "description": "5V LDO regulated output pin, rated 7mA (typical), with ~8mA short-circuit current limit. A 1uF-4.7uF ceramic decoupling capacitor must be placed between VCC and GND as close to the pin as possible. Can be used as a supply for external control circuitry." }, { "number": "4", "name": "EN", "type": "input",- "description": "Enable / PWM dimming input. Chip enables when the pin rises above V_EN_H (1.4V typ) and disables (low-power sleep) when it falls below V_EN_L (0.6V typ). Accepts PWM dimming from 100Hz up to 10kHz (I_OUT scales linearly with duty cycle). Has an internal 800kΩ pull-down; low-voltage pin - can be tied directly to VCC for always-on operation. Absolute max 6V referenced to GND."+ "description": "Enable / dimming input. Accepts a PWM dimming signal up to 10kHz. VEN_H \u2265 1.4V (enable), VEN_L \u2264 0.6V (disable). Absolute max to GND: -0.3V to +6V. Tie to VCC for always-on operation." }, { "number": "5", "name": "VIN", "type": "power_in",- "description": "Main input supply pin, 12V-60V recommended (survives 80V transients). Also serves as the top-of-sense-resistor connection for LED current sensing (R_SENSE is placed between VIN and CSN). Requires a 4.7uF X5R/X7R ceramic bypass capacitor to GND placed close to the pin. Absolute max 60V referenced to GND."+ "description": "Input supply / current-sense high side. Connects to the LED current-sense resistor RSence (other side goes to CSN). Recommended operating range 12V-60V, absolute max -0.3V to +60V (transient up to 80V)." }, { "number": "6", "name": "CSN", "type": "input",- "description": "LED current-sense input. Connects to the bottom of the external current-sense resistor R_SENSE (top is at VIN). Regulates so that V_VIN − V_CSN = 0.18V typical, giving I_OUT = 0.18V/R_SENSE. CSN bias current 12uA typical. High-impedance node - keep trace short and away from the SW node. Absolute max range VIN−6V to VIN+0.3V."+ "description": "LED current-sense negative input. Connects to the low side of the external current-sense resistor RSence. Regulated VIN\u2212VCSN \u2248 0.18V; output current IOUT = 0.18V / RSence. CSN bias current ~12uA. Absolute max: (VIN\u22126V) to (VIN+0.3V)." } ], "provenance": {@@ -126,8 +126,5 @@ "docs/lgs6305-datasheet.pdf", "viewers/symbol.html", "viewers/footprint.html"- ],- "visibility": {- "public": true- }+ ] }