← Commit history

ld7792sgs: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·d8e5613ba4 · ·parent 86e47c5
1 file changed +122−1
page.json+122−1
@@ -33,5 +33,126 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "LD7792SGS",+    "manufacturer": "Leadtrend Tech",+    "package": "SOP-16",+    "pin_count": 16,+    "category": "AC-DC Controllers and Regulators",+    "parts": {+      "symbol": "ld7792sgs.kicad_sym",+      "footprint": "ld7792sgs.kicad_mod",+      "model_3d": "ld7792sgs-etched.glb",+      "model_3d_plain": "ld7792sgs.glb",+      "model_3d_step": "ld7792sgs-etched.step",+      "model_3d_step_plain": "ld7792sgs.step",+      "lbr": "ld7792sgs.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage pin. Recommended operating range 10 V to 29 V; UVLO(on)=18 V typ, UVLO(off)=8 V typ, VCC OVP=31.5 V typ, PDR=7 V typ. Bypass with a 22-100 uF capacitor."+      },+      {+        "number": "2",+        "name": "GND",+        "type": "power_in",+        "description": "Ground return for the controller. All small-signal returns and current-sense resistors reference to this pin."+      },+      {+        "number": "3",+        "name": "FBCOMP",+        "type": "input",+        "description": "Voltage feedback pin for the Flyback stage. Connect a photo-coupler to close the secondary-side regulation loop. Also used for OLP (VOLP=4.2 V typ), burst mode (start 0.8 V / stop 0.4 V), PFC on/off threshold and heavy-load trigger (2.9 V). Internally divided 1/5.5 into the PWM comparator; open-loop clamp 5.4 V typ."+      },+      {+        "number": "4",+        "name": "FBAUX",+        "type": "input",+        "description": "Zero-current detection and over-voltage protection for the Flyback unit. Sensed via a resistor from the transformer auxiliary winding; ZCD trip 50 mV, OVP trigger current 300 uA (4-cycle debounce), upper clamp 2 V, lower clamp 0 V."+      },+      {+        "number": "5",+        "name": "OTP",+        "type": "input",+        "description": "External over-temperature protection pin. Sources 80 uA typ through an external NTC to ground; turn-off trip 1.0 V typ (with 400-600 us debounce), turn-on 1.35 V typ. Auto-recovery when temperature falls."+      },+      {+        "number": "6",+        "name": "PFCCOMP",+        "type": "output",+        "description": "Output of the PFC voltage-loop transconductance error amplifier (GM=80 umho typ). Connect a 0.1-2.2 uF compensation capacitor to GND. Upper clamp 5.2 V typ, minimum clamp 0.9 V; PFC burst mode stop threshold 1.0 V typ."+      },+      {+        "number": "7",+        "name": "PFCONOFF",+        "type": "input",+        "description": "Threshold-voltage setting pin for PFC ON/OFF loading control (compared against FBCOMP). Sources 24.5 uA typ for the PFC-OFF threshold and 25.75 uA typ for the PFC-ON threshold; set the threshold with an external resistor to GND."+      },+      {+        "number": "8",+        "name": "PFCAUX",+        "type": "input",+        "description": "Zero-current detection input for the PFC boost stage. Connect through a 10-51 kohm resistor to the PFC auxiliary winding (recommended current ~1 mA, max 1.5 mA). ZCD trip 0.2 V, upper clamp 4 V, ZCD time-out 50 us typ."+      },+      {+        "number": "9",+        "name": "VOSENSE",+        "type": "input",+        "description": "PFC output voltage sense input. Regulation reference is 2.5 V; PFC OVP trip 2.63 V (0.13 V hysteresis). Sources 8 uA at low line (VHV<=210 V) for line-compensation, 0 uA at high line (>=230 V). Enable/disable thresholds 1.1/0.9 V; internal pull-down 6 Mohm typ. Recommended capacitor <=10 nF."+      },+      {+        "number": "10",+        "name": "FBSENSE",+        "type": "input",+        "description": "Flyback current-sense input. Connect to the Flyback MOSFET source sense resistor to implement cycle-by-cycle peak-current limit at VOCQR=0.65 V typ (350 ns LEB, 80 ns delay). OCP high-line compensation adds 200 uA through an external ROCP (100-1k ohm) when FBCOMP>2.9 V."+      },+      {+        "number": "11",+        "name": "PFCSENSE",+        "type": "input",+        "description": "PFC current-sense input. Connect to the PFC MOSFET source sense resistor for cycle-by-cycle current limit; trip threshold 0.52 V at low line, 0.40 V at high line (>=230 V) with 250 ns LEB. Sense resistor value also selects PWM vs QRM frequency reduction mode (<=220 ohm PWM, >=820 ohm QRM)."+      },+      {+        "number": "12",+        "name": "PFCDRIVER",+        "type": "output",+        "description": "Gate-drive output for the external PFC boost MOSFET. CMOS totem-pole with 500/-1000 mA drive; output clamped at 13 V typ (VCC=17 V), rise time 130 ns / fall time 45 ns into 3 nF. Absolute max -0.3 V to 20 V."+      },+      {+        "number": "13",+        "name": "FBDRIVER",+        "type": "output",+        "description": "Gate-drive output for the external Flyback MOSFET. CMOS totem-pole with 500/-1000 mA drive; output clamped at 13 V typ (VCC=17 V), rise time 130 ns / fall time 45 ns into 3 nF. Absolute max -0.3 V to 20 V."+      },+      {+        "number": "14",+        "name": "CT",+        "type": "passive",+        "description": "External timing capacitor pin. Sets OLP debounce time, PFC turn-off debounce time and Flyback soft-start period; e.g. CT=47 nF gives FB soft-start 10 ms, OLP debounce 64 ms, PFC turn-off debounce 1 s."+      },+      {+        "number": "15",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection. Leave floating or tie to GND per PCB practice."+      },+      {+        "number": "16",+        "name": "HV",+        "type": "power_in",+        "description": "High-voltage startup and line-sensing pin. Connect to AC line/neutral (input side of bridge diode preferred) through a 10-50 kohm resistor to source the VCC start-up current (1.5 mA below PDR, 3 mA between PDR and UVLO(on)); shut off after UVLO(on) to eliminate startup loss. Also senses AC peak for brown-in (105 V typ) / brown-out (85 V typ), high/low line detection (230 V / 210 V typ) and X-cap discharge (3 mA). Absolute max 650 V; add a 10 kohm series resistor to limit negative-spike current."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}