← Commit history
ld7576gs: restore the component block (pinout + model declarations) from this page's own README and symbol
1 file changed
+74−1
page.json+74−1@@ -33,5 +33,78 @@ "author": { "name": "Ray", "email": "[email protected]"+ },+ "component": {+ "mpn": "LD7576GS",+ "manufacturer": "Leadtrend Tech",+ "package": "SOP-8",+ "pin_count": 8,+ "category": "AC-DC Controllers and Regulators",+ "parts": {+ "symbol": "ld7576gs.kicad_sym",+ "footprint": "ld7576gs.kicad_mod",+ "model_3d": "ld7576gs-etched.glb",+ "model_3d_plain": "ld7576gs.glb",+ "model_3d_step": "ld7576gs-etched.step",+ "model_3d_step_plain": "ld7576gs.step",+ "lbr": "ld7576gs.lbr"+ },+ "pins": [+ {+ "number": "1",+ "name": "CT",+ "type": "input",+ "description": "Programs the low-frequency timer / OLP delay time via an external capacitor to GND (recommended 0.047 µF to 0.1 µF, X7R; ~45 mS delay at 0.047 µF, ~110 mS at 0.1 µF). Also serves as a latch-mode trigger: pulling this pin below 0.8 V latches the controller off until AC power is recycled."+ },+ {+ "number": "2",+ "name": "COMP",+ "type": "input",+ "description": "Voltage feedback pin (analogous to UC384X COMP). Driven by an opto-coupler from the secondary-side TL431 to close the regulation loop. Requires ≥102 pF X7R ceramic cap; open-loop voltage ~5.6 V; green-mode threshold ~2.35 V; OLP trip level 5.0 V; pulling below 1.2 V disables the gate output."+ },+ {+ "number": "3",+ "name": "CS",+ "type": "input",+ "description": "Current sense pin for the primary MOSFET current. Maximum input threshold 0.85 V (typ), 230 nS internal leading-edge blanking, ~1 MΩ input impedance, 100 nS delay to output. Absolute max -0.3 V to +7 V; an external R-C filter is recommended for high-power designs to suppress negative turn-on spikes."+ },+ {+ "number": "4",+ "name": "GND",+ "type": "power_in",+ "description": "Device ground return for all internal circuitry and the gate driver. Should have a short, low-inductance layout back to the CT capacitor and CS sense resistor."+ },+ {+ "number": "5",+ "name": "OUT",+ "type": "output",+ "description": "Gate drive output for the external power MOSFET. CMOS totem-pole buffer with typical 500 mA source/sink capability; typical rise/fall 50 nS / 30 nS into 1 nF; maximum duty-cycle 75%. Absolute max -0.3 V to Vcc+0.3 V; includes an internal anti-floating pull-low resistor."+ },+ {+ "number": "6",+ "name": "VCC",+ "type": "power_in",+ "description": "Supply voltage for the controller. Recommended operating range 11 V to 25 V (absolute max 30 V); UVLO(on) 16 V typ, UVLO(off) 10 V typ; OVP trip 28 V typ. Bypass with 10 µF to 47 µF; startup current <100 µA while the HV pin charges this rail."+ },+ {+ "number": "7",+ "name": "NC",+ "type": "unconnected",+ "description": "No-connect. Present on the SOP-8 / DIP-8 packages only (absent from the SOP-7 variant). Leave floating."+ },+ {+ "number": "8",+ "name": "HV",+ "type": "input",+ "description": "High-voltage startup input; connect to the positive terminal of the bulk (rectified DC) capacitor through a recommended 40 kΩ current-limit resistor. Sources ~1 mA (typ) into Vcc during startup and shuts off once Vcc trips UVLO(on) to eliminate steady-state startup losses. Absolute max 600 V; off-state leakage <35 µA at 500 V."+ }+ ],+ "provenance": {+ "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+ },+ "viewers": {+ "symbol": "viewers/symbol.html",+ "footprint": "viewers/footprint.html"+ } }-}+}