← Commit history
README.mdadded+107@@ -0,0 +1,107 @@+# LAN9252I++**Microchip** · Ethernet Controllers · QFN-64-EP(9x9)++LAN9252I from Microchip, in a QFN-64-EP(9x9). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | OSCI | input | External 25 MHz crystal input. Can also be driven single-ended by a clock oscillator (leave OSCO unconnected in that case). |+| 2 | OSCO | output | External 25 MHz crystal output. |+| 3 | OSCVDD12 | power_in | Crystal oscillator +1.2V supply. Supplied by the on-chip regulator unless REG_EN configures regulator-off mode. |+| 4 | OSCVSS | power_in | Crystal oscillator ground. |+| 5 | VDD33 | power_in | +3.3V supply for the internal regulators. Must be supplied even if internal regulators are disabled. |+| 6 | VDDCR | power_in | +1.2V digital core supply. Supplied by the on-chip regulator unless REG_EN configures regulator-off mode. Pin 6 needs 1 µF and 470 pF decoupling caps in parallel to ground. |+| 7 | REG_EN | input | Regulator enable. Tie to 3.3V to enable the internal 1.2V regulators; tie low to disable and supply VDDCR/OSCVDD12 externally. |+| 8 | FXLOSEN | input | Port A and B FX-LOS enable strap. 3-level input: <1V selects FX-SD / copper twisted pair, 1.5V selects FX-LOS on port A only, >2V selects FX-LOS on both ports. |+| 9 | FXSDA/FXLOSA/FXSDENA | bidirectional | Port A fiber signal-detect (FXSDA, LVPECL input, >2V typ = valid), fiber loss-of-signal (FXLOSA, Schmitt input with pull-up), or FX-SD enable strap (FXSDENA, analog input; >1V typ selects FX-SD). Function selected by FXLOSEN. |+| 10 | FXSDB/FXLOSB/FXSDENB | bidirectional | Port B fiber signal-detect (FXSDB, LVPECL input, >2V typ = valid), fiber loss-of-signal (FXLOSB, Schmitt input with pull-up), or FX-SD enable strap (FXSDENB, analog input; >1V typ selects FX-SD). Function selected by FXLOSEN. |+| 11 | RST# | bidirectional | Active-low system reset. Input from external hardware; also driven low by the device during POR or an EtherCAT reset command sequence. Internal pull-up; open-drain output. |+| 12 | D2/AD2/SOF/SIO2 | bidirectional | Chip-mode muxed: HBI-Indexed data D2, HBI-Multiplexed AD2, Digital-I/O Start-of-Frame output SOF, or SPI/SQI SIO2. |+| 13 | D1/AD1/EOF/SO/SIO1 | bidirectional | Chip-mode muxed: HBI D1, HBI AD1, Digital-I/O End-of-Frame output EOF, SPI serial data output SO, or SQI SIO1. |+| 14 | VDDIO | power_in | +1.8V to +3.3V variable I/O supply. |+| 15 | D14/AD14/DIGIO8/GPI8/GPO8/MII_TXD3/TX_SHIFT1 | bidirectional | Chip-mode muxed: HBI D14, HBI AD14, Digital-I/O DIGIO8, SPI+GPIO GPI8/GPO8, or SPI+MII MII_TXD3 / TX_SHIFT1 strap. |+| 16 | D13/AD13/DIGIO7/GPI7/GPO7/MII_TXD2/TX_SHIFT0 | bidirectional | Chip-mode muxed: HBI D13, HBI AD13, Digital-I/O DIGIO7, SPI+GPIO GPI7/GPO7, or SPI+MII MII_TXD2 / TX_SHIFT0 strap. |+| 17 | D0/AD0/WD_STATE/SI/SIO0 | bidirectional | Chip-mode muxed: HBI D0, HBI AD0, Digital-I/O SyncManager Watchdog State output WD_STATE, SPI serial data input SI, or SQI SIO0. |+| 18 | SYNC1/LATCH1 | bidirectional | Distributed-Clock Sync1 (output) or Latch1 (input). Direction is bitwise configurable. High-impedance until EEPROM is loaded. |+| 19 | D9/AD9/LATCH_IN/SCK | bidirectional | Chip-mode muxed: HBI D9, HBI AD9, Digital-I/O external data latch input LATCH_IN, or SPI/SQI serial clock SCK. |+| 20 | VDDIO | power_in | +1.8V to +3.3V variable I/O supply. |+| 21 | D12/AD12/DIGIO6/GPI6/GPO6/MII_TXD1 | bidirectional | Chip-mode muxed: HBI D12, HBI AD12, Digital-I/O DIGIO6, SPI+GPIO GPI6/GPO6, or SPI+MII MII_TXD1. |+| 22 | D11/AD11/DIGIO5/GPI5/GPO5/MII_TXD0 | bidirectional | Chip-mode muxed: HBI D11, HBI AD11, Digital-I/O DIGIO5, SPI+GPIO GPI5/GPO5, or SPI+MII MII_TXD0. |+| 23 | D10/AD10/DIGIO4/GPI4/GPO4/MII_TXEN | bidirectional | Chip-mode muxed: HBI D10, HBI AD10, Digital-I/O DIGIO4, SPI+GPIO GPI4/GPO4, or SPI+MII MII_TXEN. |+| 24 | VDDCR | power_in | +1.2V digital core supply (regulator output or external). |+| 25 | A1/ALELO/OE_EXT/MII_CLK25 | bidirectional | Chip-mode muxed: HBI address bit A1, HBI Address-Latch-Enable Low ALELO, Digital-I/O Output-Enable OE_EXT (active low clears output data), or SPI+MII 25 MHz clock output MII_CLK25. |+| 26 | A3/DIGIO11/GPI11/GPO11/MII_RXDV | bidirectional | Chip-mode muxed: HBI address bit A3, Digital-I/O DIGIO11, SPI+GPIO GPI11/GPO11, or SPI+MII receive-data-valid MII_RXDV. No function in HBI-Multiplexed mode. |+| 27 | A4/DIGIO12/GPI12/GPO12/MII_RXD0 | bidirectional | Chip-mode muxed: HBI address bit A4, Digital-I/O DIGIO12, SPI+GPIO GPI12/GPO12, or SPI+MII MII_RXD0. |+| 28 | CS/DIGIO13/GPI13/GPO13/MII_RXD1 | bidirectional | Chip-mode muxed: HBI chip-select CS, Digital-I/O DIGIO13, SPI+GPIO GPI13/GPO13, or SPI+MII MII_RXD1. |+| 29 | A2/ALEHI/DIGIO10/GPI10/GPO10/LINKACTLED2/MII_LINKPOL | bidirectional | Chip-mode muxed: HBI address bit A2, HBI Address-Latch-Enable High ALEHI, Digital-I/O DIGIO10, SPI+GPIO GPI10/GPO10, SPI+MII link/activity LED port 2 LINKACTLED2, or MII link-polarity strap MII_LINKPOL. |+| 30 | WR/ENB/DIGIO14/GPI14/GPO14/MII_RXD2 | bidirectional | Chip-mode muxed: HBI write strobe WR / data-enable ENB, Digital-I/O DIGIO14, SPI+GPIO GPI14/GPO14, or SPI+MII MII_RXD2. |+| 31 | RD/RD_WR/DIGIO15/GPI15/GPO15/MII_RXD3 | bidirectional | Chip-mode muxed: HBI read strobe RD / read-or-write RD_WR, Digital-I/O DIGIO15, SPI+GPIO GPI15/GPO15, or SPI+MII MII_RXD3. |+| 32 | VDDIO | power_in | +1.8V to +3.3V variable I/O supply. |+| 33 | A0/D15/AD15/DIGIO9/GPI9/GPO9/MII_RXER | bidirectional | Chip-mode muxed: HBI address bit A0 or upper data D15, HBI AD15, Digital-I/O DIGIO9, SPI+GPIO GPI9/GPO9, or SPI+MII receive-error MII_RXER. |+| 34 | SYNC0/LATCH0 | bidirectional | Distributed-Clock Sync0 (output) or Latch0 (input). Direction is bitwise configurable. High-impedance until EEPROM is loaded. |+| 35 | D3/AD3/WD_TRIG/SIO3 | bidirectional | Chip-mode muxed: HBI D3, HBI AD3, Digital-I/O SyncManager Watchdog Trigger output WD_TRIG, or SQI SIO3. |+| 36 | D6/AD6/DIGIO0/GPI0/GPO0/MII_RXCLK | bidirectional | Chip-mode muxed: HBI D6, HBI AD6, Digital-I/O DIGIO0, SPI+GPIO GPI0/GPO0, or SPI+MII receive clock MII_RXCLK. |+| 37 | VDDIO | power_in | +1.8V to +3.3V variable I/O supply. |+| 38 | VDDCR | power_in | +1.2V digital core supply (regulator output or external). |+| 39 | D7/AD7/DIGIO1/GPI1/GPO1/MII_MDC | bidirectional | Chip-mode muxed: HBI D7, HBI AD7, Digital-I/O DIGIO1, SPI+GPIO GPI1/GPO1, or SPI+MII SMI clock MII_MDC. |+| 40 | D8/AD8/DIGIO2/GPI2/GPO2/MII_MDIO | bidirectional | Chip-mode muxed: HBI D8, HBI AD8, Digital-I/O DIGIO2, SPI+GPIO GPI2/GPO2, or SPI+MII SMI data MII_MDIO (needs external pull-up). |+| 41 | TESTMODE | input | Test-mode input; must be tied to VSS for proper operation. Internal pull-down. |+| 42 | EESDA/TMS | bidirectional | Dual-function: EEPROM I2C serial data (open-drain, requires external pull-up) or JTAG test-mode-select TMS. |+| 43 | EESCL/TCK | bidirectional | Dual-function: EEPROM I2C serial clock (open-drain, requires external pull-up) or JTAG test-clock TCK. |+| 44 | IRQ | output | Interrupt request output. Polarity, source, and buffer type (push-pull or open-drain) are programmable via the Interrupt Configuration Register (IRQ_CFG). |+| 45 | RUNLED/E2PSIZE | bidirectional | Run-LED output (open-drain/open-source, controlled by AL Status Register) and EEPROM-size configuration strap (low = 1K-16K bit, high = 32K bit-4M bit). |+| 46 | LINKACTLED1/TDI/CHIP_MODE1 | bidirectional | Port 1 Link/Activity LED output (open-drain/open-source), JTAG test-data-input TDI, or Chip-Mode configuration strap CHIP_MODE1. |+| 47 | VDDIO | power_in | +1.8V to +3.3V variable I/O supply. |+| 48 | LINKACTLED0/TDO/CHIP_MODE0 | bidirectional | Port 0 Link/Activity LED output (open-drain/open-source), JTAG test-data-output TDO, or Chip-Mode configuration strap CHIP_MODE0. |+| 49 | D4/AD4/DIGIO3/GPI3/GPO3/MII_LINK | bidirectional | Chip-mode muxed: HBI D4, HBI AD4, Digital-I/O DIGIO3, SPI+GPIO GPI3/GPO3, or SPI+MII link-status input MII_LINK. |+| 50 | D5/AD5/OUTVALID/SCS# | bidirectional | Chip-mode muxed: HBI D5, HBI AD5, Digital-I/O Output-Valid output OUTVALID, or SPI/SQI slave chip-select SCS# (active low, pull-up). |+| 51 | VDD33TXRX1 | power_in | +3.3V analog supply for Port A PHY (or separate ~2.5V through magnetics). |+| 52 | TXNA | bidirectional | Port A twisted-pair TX/RX negative channel 1 (AIO). In fiber mode: Port A FX TX negative (OLVPECL output). MDIX may internally swap TX/RX. |+| 53 | TXPA | bidirectional | Port A twisted-pair TX/RX positive channel 1 (AIO). In fiber mode: Port A FX TX positive (OLVPECL output). MDIX may internally swap TX/RX. |+| 54 | RXNA | bidirectional | Port A twisted-pair TX/RX negative channel 2 (AIO). In fiber mode: Port A FX RX negative (analog input). MDIX may internally swap TX/RX. |+| 55 | RXPA | bidirectional | Port A twisted-pair TX/RX positive channel 2 (AIO). In fiber mode: Port A FX RX positive (analog input). MDIX may internally swap TX/RX. |+| 56 | VDD12TX1 | power_in | +1.2V Port A transmitter supply. Must be tied to VDD12TX2. Supplied by on-chip regulator or an external 1.2V source. |+| 57 | RBIAS | passive | Bias reference. Connect through a 12.1 kΩ ±1% resistor to ground (nominal 1.2V, ~1 mW dissipation). |+| 58 | VDD33BIAS | power_in | +3.3V master-bias analog supply. |+| 59 | VDD12TX2 | power_in | +1.2V Port B transmitter supply. Must be tied to VDD12TX1. Supplied by on-chip regulator or an external 1.2V source. |+| 60 | RXPB | bidirectional | Port B twisted-pair TX/RX positive channel 2 (AIO). In fiber mode: Port B FX RX positive (analog input). MDIX may internally swap TX/RX. |+| 61 | RXNB | bidirectional | Port B twisted-pair TX/RX negative channel 2 (AIO). In fiber mode: Port B FX RX negative (analog input). MDIX may internally swap TX/RX. |+| 62 | TXPB | bidirectional | Port B twisted-pair TX/RX positive channel 1 (AIO). In fiber mode: Port B FX TX positive (OLVPECL output). MDIX may internally swap TX/RX. |+| 63 | TXNB | bidirectional | Port B twisted-pair TX/RX negative channel 1 (AIO). In fiber mode: Port B FX TX negative (OLVPECL output). MDIX may internally swap TX/RX. |+| 64 | VDD33TXRX2 | power_in | +3.3V analog supply for Port B PHY (or separate ~2.5V through magnetics). |+| EP | VSS | power_in | Exposed pad, common ground. Must be connected to the ground plane with a via array. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip |+| Package | QFN-64-EP(9x9) |+| Category | Interface |+| Pins | 65 |++## Ordering variants++- `LAN9252IML`+- `LAN9252ITML`+- `LAN9252IPT`+- `LAN9252ITPT`++## CAD (KiCad official)++- Symbol: `LAN9252I`+- Footprint: `Package_DFN_QFN:QFN-64-1EP_9x9mm_P0.5mm_EP6x6mm`+- 3D model: QFN-64-EP(9x9) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip datasheet](docs/lan9252i-datasheet.pdf) (329 pp, sha256 `562783e8c3ae2843`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lan9252i-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "lan9252i",+ "version": "0.1.0",+ "type": "component",+ "description": "Microchip Ethernet Controllers, QFN-64-EP(9x9). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "lan9252i"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lan9252i.kicad_sym",+ "lan9252i.kicad_mod",+ "lan9252i.glb",+ "lan9252i.step",+ "lan9252i.lbr",+ "docs/hero.png",+ "docs/lan9252i-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}