← Commit history
README.mdadded+98@@ -0,0 +1,98 @@+# LAN7500I-ABZJ++**Microchip Tech** · Ethernet Controllers · QFN-56-EP(8x8)++LAN7500I-ABZJ from Microchip Tech, in a QFN-56-EP(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | TDI | input | JTAG (IEEE 1149.1) test data input. Buffer VIS with 50 uA internal pull-up. Tie to VDDVARIO when unused. |+| 2 | TCK | input | JTAG (IEEE 1149.1) test clock. Buffer VIS with 50 uA internal pull-down. Tie to VSS when unused. |+| 3 | TMS | input | JTAG (IEEE 1149.1) test mode select. Buffer VIS with 50 uA internal pull-up. Tie to VDDVARIO when unused. |+| 4 | TDO | output | JTAG (IEEE 1149.1) test data output. Buffer VO8 (variable-voltage 8 mA push-pull). |+| 5 | XI | input | External 25 MHz crystal input (ICLK). May also be driven by a single-ended clock oscillator; in that case leave XO unconnected. |+| 6 | XO | output | External 25 MHz crystal output (OCLK). Leave unconnected when XI is driven by a single-ended oscillator. |+| 7 | VDDVARIO | power_in | +3.3 V / +2.5 V variable I/O power supply input. Sets the digital I/O rail voltage; four VDDVARIO pins on the package. |+| 8 | VDD12CORE | power_in | +1.2 V digital core power supply input. Six VDD12CORE pins on the package. |+| 9 | SW_MODE | output | Switching regulator mode control output (VO6, 6 mA). When asserted, places the external switching regulator into power-saving mode. Polarity/assertion controlled by SW_MODE_POL and SW_MODE_SEL bits of Configuration Flags 1. |+| 10 | GPIO7 | bidirectional | General-purpose I/O 7. Programmable as push-pull, open-drain, or Schmitt-triggered input. Buffer VIS/VO8/VOD8 with 50 uA internal pull-up. |+| 11 | VDD12CORE | power_in | +1.2 V digital core power supply input. |+| 12 | USBDM | bidirectional | USB D- analog bidirectional (AIO). Functionality may be swapped with USBDP via the Port Swap bit of Configuration Flags 0. |+| 13 | USBDP | bidirectional | USB D+ analog bidirectional (AIO). Functionality may be swapped with USBDM via the Port Swap bit of Configuration Flags 0. |+| 14 | VBUS_DET | input | Upstream VBUS power detect input (IS_5V, 5 V tolerant Schmitt input with internal pull-down). For bus-powered operation, tie to VDD33A. For self-powered operation, refer to reference schematics. |+| 15 | VDD33A | power_in | +3.3 V analog power supply input. |+| 16 | USBRBIAS | passive | External USB bias resistor (AI). Sets HS transmit current level and on-chip termination impedance. Connect an external 12 kOhm 1% resistor to ground. |+| 17 | VDD12USBPLL | power_in | +1.2 V USB PLL power supply input. |+| 18 | GPIO8 | bidirectional | General-purpose I/O 8. Programmable as push-pull, open-drain, or Schmitt-triggered input. Buffer VIS/VO6/VOD6 with 50 uA internal pull-up (6 mA drive rather than the usual 8 mA). |+| 19 | VDDVARIO | power_in | +3.3 V / +2.5 V variable I/O power supply input. |+| 20 | VDD12CORE | power_in | +1.2 V digital core power supply input. |+| 21 | GPIO9 | bidirectional | General-purpose I/O 9. Programmable as push-pull, open-drain, or Schmitt-triggered input. Buffer VIS/VO8/VOD8 with 50 uA internal pull-up. |+| 22 | GPIO10 | bidirectional | General-purpose I/O 10. Programmable as push-pull, open-drain, or Schmitt-triggered input. Buffer VIS/VO8/VOD8 with 50 uA internal pull-up. |+| 23 | VDD12CORE | power_in | +1.2 V digital core power supply input. |+| 24 | VDDVARIO | power_in | +3.3 V / +2.5 V variable I/O power supply input. |+| 25 | GPIO11 | bidirectional | General-purpose I/O 11. Programmable as push-pull, open-drain, or Schmitt-triggered input. Buffer VIS/VO8/VOD8 with 50 uA internal pull-up. |+| 26 | EECLK | output | EEPROM clock output to the external MicroWire EEPROM (VO8). |+| 27 | EEDI | input | EEPROM data in. Driven by the EEDO output of the external EEPROM. Buffer VIS with internal pull-down. |+| 28 | EEDO | output | EEPROM data out. Drives the EEDI input of the external EEPROM (VO8). |+| 29 | EECS | output | EEPROM chip select (VO8). May tri-state briefly during power-up; an external pull-down is recommended to prevent false selection. |+| 30 | VDD12CORE | power_in | +1.2 V digital core power supply input. |+| 31 | GPIO0/LED0 | bidirectional | Muxed pin: GPIO0 (VIS/VO8/VOD8 with pull-up) or Indicator LED0 (VOD8, open-drain LED driver). Default at reset is GPIO. Used with LED1 to indicate Link/Speed or Link/Speed/Activity. |+| 32 | GPIO1/LED1 | bidirectional | Muxed pin: GPIO1 or Indicator LED1. LED1 combines with LED0 to indicate Ethernet Link/Speed or Link/Speed/Activity. Default: GPIO. |+| 33 | GPIO2/LED2 | bidirectional | Muxed pin: GPIO2 or Indicator LED2 (Ethernet Link and Activity, or Activity only). Default: GPIO. |+| 34 | GPIO3/LED3 | bidirectional | Muxed pin: GPIO3 or Indicator LED3 (Ethernet Link indicator). Default: GPIO. |+| 35 | GPIO4/LED4 | bidirectional | Muxed pin: GPIO4 or Indicator LED4 (Ethernet Full-Duplex indicator). Default: GPIO. |+| 36 | VDD12CORE | power_in | +1.2 V digital core power supply input. |+| 37 | VDDVARIO | power_in | +3.3 V / +2.5 V variable I/O power supply input. |+| 38 | GPIO5/PME | bidirectional | Muxed pin: GPIO5 (VIS/VO8/VOD8 with pull-up) or PME output (VO8/VOD8). When PME mode of operation is in effect this pin signals Power Management Event. |+| 39 | TEST | input | Test pin. Must always be connected to VSS for proper operation. |+| 40 | GPIO6/PME_MODE_SEL | bidirectional | Muxed pin: GPIO6 (VIS/VO8/VOD8 with pull-up) or PME_MODE_SEL input (VIS with pull-up) when PME mode is in effect. |+| 41 | ETHRBIAS | passive | External PHY bias resistor (AI). Used for internal bias circuits. Connect to an external 8.06 kOhm 1% resistor to ground. |+| 42 | nRESET/PME_CLEAR | input | Muxed pin: active-low system reset (nRESET, VIS with pull-up) allowing external hardware to reset the device, or PME_CLEAR input when PME mode is in effect. Assertion of nRESET is required following power-on. |+| 43 | TR0N | bidirectional | Ethernet TX/RX negative channel 0 (AIO). Connects to the negative side of magnetics pair 0 for 10/100/1000BASE-T. |+| 44 | TR0P | bidirectional | Ethernet TX/RX positive channel 0 (AIO). Connects to the positive side of magnetics pair 0 for 10/100/1000BASE-T. |+| 45 | VDD12A | power_in | +1.2 V Ethernet analog port power supply input (channels 0-3). Four VDD12A pins on the package. |+| 46 | TR1N | bidirectional | Ethernet TX/RX negative channel 1 (AIO). |+| 47 | TR1P | bidirectional | Ethernet TX/RX positive channel 1 (AIO). |+| 48 | VDD12A | power_in | +1.2 V Ethernet analog port power supply input. |+| 49 | VDD12BIAS | power_in | +1.2 V Ethernet bias power supply input. |+| 50 | VDD12PLL | power_in | +1.2 V Ethernet PLL power supply input. |+| 51 | TR2N | bidirectional | Ethernet TX/RX negative channel 2 (AIO). |+| 52 | TR2P | bidirectional | Ethernet TX/RX positive channel 2 (AIO). |+| 53 | VDD12A | power_in | +1.2 V Ethernet analog port power supply input. |+| 54 | TR3N | bidirectional | Ethernet TX/RX negative channel 3 (AIO). |+| 55 | TR3P | bidirectional | Ethernet TX/RX positive channel 3 (AIO). |+| 56 | VDD12A | power_in | +1.2 V Ethernet analog port power supply input. |+| 57 | VSS | power_in | Exposed pad on bottom of package. Common ground; must be connected to ground. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip Tech |+| Package | QFN-56-EP(8x8) |+| Category | Interface |+| Pins | 57 |++## Ordering variants++Same part, different packaging or reel option.++- `LAN7500I-ABZJ`++## CAD (KiCad official)++- Symbol: `LAN7500I-ABZJ`+- Footprint: `Package_DFN_QFN:QFN-56-1EP_8x8mm_P0.5mm_EP4.5x5.2mm`+- 3D model: QFN-56-EP(8x8) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip Tech datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588915962896920576) (56 pp, sha256 `a786a4302ef5dbd6`, retrieved 2026-08-17, tier: lcsc)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/lan7500i-abzj-datasheet.pdf)
page.jsonadded+34@@ -0,0 +1,34 @@+{+ "slug": "lan7500i-abzj",+ "version": "0.1.0",+ "type": "component",+ "description": "Microchip Tech Ethernet Controllers, QFN-56-EP(8x8). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+ "tags": [+ "component",+ "interface",+ "lan7500i-abzj"+ ],+ "dependencies": {},+ "hero": {+ "type": "image",+ "path": "docs/hero.png"+ },+ "files": [+ "page.json",+ "README.md",+ "lan7500i-abzj.kicad_sym",+ "lan7500i-abzj.kicad_mod",+ "lan7500i-abzj.glb",+ "lan7500i-abzj.step",+ "lan7500i-abzj.lbr",+ "docs/hero.png",+ "docs/lan7500i-abzj-datasheet.pdf",+ "viewers/symbol.html",+ "viewers/footprint.html"+ ],+ "visibility": "public",+ "author": {+ "name": "Ray",+ "email": "[email protected]"+ }+}