← Commit history

Initial commit: component/l7987tr

Ray ·f00418adca ·
2 files changed +90
README.mdadded+56
@@ -0,0 +1,56 @@+# L7987TR++**STMicroelectronics** · DC-DC Converters · HTSSOP-16-EP++L7987TR from STMicroelectronics, in a HTSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VBIAS | power_in | Auxiliary input to supply part of the analog circuitry to increase efficiency at light load. Typically tied to the regulated output voltage or an external rail higher than 3 V; connect to signal GND (or bypass with a 1 uF ceramic) if unused. |+| 2 | VIN | power_in | DC input voltage (4.5 V to 61 V operating range). Tie both VIN pins together at the package. |+| 3 | VIN | power_in | DC input voltage (4.5 V to 61 V operating range). Tie both VIN pins together at the package. |+| 4 | VCC | power_in | Filtered DC input voltage to the internal circuitry. Bypass to signal GND with a 1 uF ceramic capacitor. |+| 5 | EN | input | Active-high enable pin (device OFF <= 0.30 V, ON >= 0.35 V). Connect to VCC if not used. |+| 6 | SS | passive | Soft-start pin. An internal 5 uA typ. current source charges an external capacitor from this pin to set the soft-start time. |+| 7 | SYNCH | bidirectional | Master/slave synchronization pin. Sources a pulse when configured as master and accepts an external sync input (>=280 kHz) when configured as slave; up to 5 slave devices can share this line. |+| 8 | COMP | output | Error-amplifier output. Compensation network (Type II or Type III) is connected between COMP and FB/GND to shape the loop response. |+| 9 | FB | input | Inverting input of the error amplifier (VFB = 0.8 V typ.). Connect to the output resistor divider to set the regulated output voltage. |+| 10 | FSW | passive | Switching-frequency programming pin. A pull-down resistor to GND selects the switching frequency (250 kHz - 1.5 MHz); leaving FSW floating sets ~250 kHz. |+| 11 | ILIM | passive | Peak-current-limit programming pin. A pull-down resistor to GND selects the inductor peak current limit; floating ILIM yields the default ~4.0 A limit. |+| 12 | PGOOD | output | Open-collector power-good output. Pulled low when the FB voltage is out of regulation (rising threshold 0.70 V typ., 30 mV hysteresis); requires an external pull-up. |+| 13 | LX | power_out | Switching node (output of the internal high-side n-DMOS). Tie both LX pins together and connect to the external inductor and freewheeling diode. |+| 14 | LX | power_out | Switching node (output of the internal high-side n-DMOS). Tie both LX pins together and connect to the external inductor and freewheeling diode. |+| 15 | BOOT | passive | Bootstrap pin for the high-side gate drive. Connect a 100 nF ceramic capacitor (typ.) between BOOT and LX; the internal regulator refreshes the boot capacitor during the off-time. |+| 16 | GND | power_in | Signal ground reference for the internal analog circuitry. |+| 17 | EP | power_in | Exposed thermal pad on package underside. Must be connected to signal GND and to a large copper area for heat dissipation (RthJA = 40 C/W on demo board). |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | HTSSOP-16-EP |+| Category | PMIC |+| Pins | 17 |++## Ordering variants++- `L7987TR`++## CAD (KiCad official)++- Symbol: `L7987TR`+- Footprint: `Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm`+- 3D model: HTSSOP-16-EP (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://www.st.com/resource/en/datasheet/l7987tr.pdf) (37 pp, sha256 `9ea1c120a6bc8ac2`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/l7987tr-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "l7987tr",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics DC-DC Converters, HTSSOP-16-EP. Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "l7987tr"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "l7987tr.kicad_sym",+    "l7987tr.kicad_mod",+    "l7987tr.glb",+    "l7987tr.step",+    "l7987tr.lbr",+    "docs/hero.png",+    "docs/l7987tr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file